Version1.
Robin 300 LEDWash Robin 300 LEDWash Wireless DMX Table of contents 1. Safety instructions.......................................................................................................... 3 2. Fixture exterior view ...................................................................................................... 5 3. Installation....................................................................................................................... 6 3.1 Connection to the mains....................
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE POWERING OR INSTALLING YOUR ROBIN 300 LEDWASH ! Save it for future reference. This device has left our premises in absolutely perfect condition. In order to maintain this condition and to ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written in this manual.
When choosing the installation spot, please make sure that the fixture is not exposed to extreme heat, moisture or dust. Air vents and slots in the fixture´s head and base are provided for ventilation, to ensure reliable operation of the device and to protect it from overheating. Do not block the LEDs array with any object when the fixture is under operation. The openings should never be covered with cloth or other materials, and never must be blocked.
2. Fixture exterior view 1 - Lens array 2 - Hold for safety cabel 3 - QVGA touch screen 4 - Control buttons 5 - Base Rear panel of the base: 6 - Moving head 7 - Fan 8 - Yoke 9 - Ethernet input 10 - 5-pin DMX IN 11 - 5-pin DMX OUT 12 - 3-pin DMX IN 13 - 3-pin DMX OUT 14 - Power cord The ENTER/DISPLAY ON button also serves for switching the display on when the fixture is disconnected from the mains.
3. Installation Fixtures must be installed by a Qualified electrician in accordance with all national and local electrical and construction codes and regulation. 3.1 Connection to the mains For protection from electric shock, the fixture must be earthed! The Robin 300 LEDWash is equipped with auto-switching power supply that automatically adjusts to any 50/60Hz AC power source from 100-240 Volts.
3.2 Installing the top hat Switch off the fixture before top hat installation 1. Go to the fixture menu and set reduced tilt movement (Personality --> Pan/Tilt Setting--> Tilt Movement Range --> reduced). 2.Unscrew the four fastening screws (3) which securing flange (4) to the head (5) and install new flange. Keep its right position- the cutouts (A) in the flange must look towards the arms. Original flange New flange 3.
3.3 Installing the eggcrate Switch off the fixture before top hat installation 1. Unscrew the four fastening screws (1) which securing top flange (2) to the head (7) and remove both flange and transparent plastic cover (3) from the head. 2. Unscrew the three fastening screws (4) which securing black eggcrate (5) to the zoom module (6) and remove it. 3. Put the transparent eggcrate on the zoom module (6) and screw it with three screws (4) with washers to the zoom module (6). 4.
3.4 Rigging the fixture The installation of the fixture has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation. The installation must always be secured with a secondary safety attachment, e.g. an appropriate catch net. This secondary safety attachment must be constructed in a way that no part of the installation can fall down if the main attachment fails.
Securing the fixture via one safety wire Securing the fixture via two safety wires 1-Fixture 2-Truss 3-Clamp 4-Mounting adapter 5-Quarter-turn fasteners 6-Safety wire 10
3.5 DMX-512 connection The fixture is equipped with both 3-pin and 5-pin XLR sockets for DMX input and output.The sockets are wired in parallel. Only use a shielded twisted-pair cable designed for RS-485 and 3-pin or 5-pin XLR-plugs and connectors in order to connect the controller with the fixture or one fixture with another.
3.6 Ethernet connection The fixtures on a data link are connected to the Ethernet with ArtNet communication protocol.The control software running on your PC (or light console) has to support Art-Net protocol. Art-Net communication protocol is a 10 Base T Ethernet protocol based on the TCP/IP.Its purpose is to allow transfer of large amounts of DMX 512 data over a wide area using standard network technology. IP address is the Internet protocol address.
Ethernet / DMX operation Options “Ethernet/DMX” has to be selected from the “Ethernet Mode” menu on the first fixture (connected to the Ethernet) in the fixture chain,next fixtures have standard DMX setting. Connect the Ethernet-input of the first fixture in the data chain with the network. Connect the DMX output of this fixture with the input of the next fixture until all fixtures are connected to the DMX chain. Caution: At the last fixture, the DMX chain has to be terminated with a terminator.
4. Control menu map Default settings=Bold print Tab Level 1 Level 2 Level 3 Addressing Settings DMX Address 001-255 Ethernet Settings Ethernet Mode Level 4 Level 5 Disable ArtNet gMAI gMA2 Art2DMX IP Address/NetMask Default IP Address Custom IP Address Net Mask Information Fixture Times Power On Time Fixture Temperatures LEDs Temperature ArtNet Universe 0-255 MANet settings MANet I/IIUniverse 1-256 MANet Session ID 1-32 Total Hours Resetable Hours Current Maximum NonRes.
Tab Level 1 Level 2 Level 3 Tilt Reverse Off, On Pan/Tilt Feedback Off, On Pan/Tilt mode Time Level 4 Speed Tilt Movemement range Stand. Reduc. Microphone Sensitivity 1-10-20 Blackout Settings Blackout During M.C. Off, On Blackout while: Pan/Tilt moving Colour Calibration Mode Off, On Init Effect Positions Pan Off, On 0-255 : Screen Settings Dimmer Fine 0-255 Display Intensity 1-10 Screen Saver Delay Off-10min. Touchscreen Lock Off-10min.
Tab Level 1 Level 2 Level 3 Level 4 Level 5 Edit Program Steps Step 1 Pan (0-255) : : : Dimmer Fine (0-255) : Step Time (0-25.5s) Step 100 Pan (0-255) : Dimmer Fine (0-255) Fade Time (0-25.
5. Robin 300 LEDWash - DMX chart Version 1.0 Mode/Channel Value Function Type of control 1 2 3 4 5 1 1 1 1 1 0-255 Pan (8 bit) Pan movement by 450° proportional 2 2 2 2 2 0-255 Pan Fine (16 bit) Fine control of pan movement proportional 3 3 3 3 3 0-255 Tilt (8bit) Tilt movement by 300° proportional 4 4 4 4 4 0-255 Tilt fine (16 bit) Fine control of tilt movement proportional 0 5 5 5 5 5 6 6 6 6 P./T. speed-set Speed Mode in menu: P./T.
Mode/Channel Value Function Type of control 1 2 3 4 5 8 - - - 15 0-255 Red fine (16 bit) - zone 1 Fine red LEDs saturation control proportional 9 - - - 16 0-255 Green (8 bit) - zone 1 Green LEDs saturation control (0-100%) proportional 10 - - - 17 0-255 Green fine (16 bit) - zone 1 Fine green LEDs saturation control proportional 11 - - - 18 0-255 Blue (8 bit) zone 1 Blue LEDs saturation control (0-100%) proportional proportional 12 - - - 19 0-255 Blue (16 bit)
Mode/Channel 1 2 3 4 5 Value Function Type of control Virtual Colour Wheel For detailed description see " Virtual colour wheel- colour mixing chart 32 16 12 7 13 0 1-2 3 4-5 6 7-9 10-12 13-15 16 17-55 56 57 - 95 96 97 – 134 135 136 - 174 175 176 -214 215 216 - 246 247 248 249 250-255 No function White 2700 K White 2700 K (Halogen lamp mode*) White 3200 K White 3200 K (Halogen lamp mode*) White 4200 K White 5600 K White 8000 K Blue (Blue=full, Red+Green+White=0) Red=0, Green->up,Blue =full, W
5.1 Virtual colour wheel colour mixing chart Robin-600 LED Wash - Virtual Colour Wheel Scale* Virtual Colour Wheel DMX 1-2 (White 2700K) 3 (White 2700K /Hal.mode/) 4-5 (White 3200K) 6 (White 3200K /Hal.
Robin 600 LED Wash - Virtual Colour Wheel Scale* Virtual Colour Wheel DMX 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 82 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 Red DMX 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 3 6 9 12 15 18 21 24 27 30 36 41 46 52 58 64 68 74 80 86 92 98 Page 2 21 Green DMX 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255
Robin 600 LED Wash - Virtual Colour Wheel Scale* Virtual Colour Wheel DMX 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 Red DMX 104 110 119 129 138 147 156 165 174 183 192 201 210 219 228 240 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255
Robin 600 LED Wash - Virtual Colour Wheel Scale* Virtual Colour Wheel DMX 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 Red DMX 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 246 237 228 219 210 201 192 183 174 165
Robin 600 LED Wash - Virtual Colour Wheel Scale* Virtual Colour Wheel DMX 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248-255 (Rainbow+ zone effects) Red DMX 129 119 110 104 98 91 84 77 70 63 56 49 42 35 28 21 14 7 0 **** * Colour scale as an illustration only 5.
6. Control menu The Robin 300 LEDWash Light is equipped with the QVGA Robe touch screen with battery backup which allows to set the fixture´s behaviour according to your needs, obtain information on its operation, test its various parts and lastly program it, if it has to be used in a stand-alone mode. The fixture´s menu can be controlled either by the control buttons or directly by touching the icon. Control buttons on the front panel: [ESCAPE] button used to leave the menu without saving changes.
Touch any part of the screen or press the [ENTER/Display On] button to display the initial screen with the current stored DMX address: Touch the green arrow at the bottom right corner of the screen or press the [ENTER/Display On] button to enter the " Address" menu. An item (such as a Tab, menu item, text box, icon) may be selected from a screen by simply touching the item in the list or by pressing the [NEXT] or [PREV] buttons to scroll through list items.
6.2 Tab "Information" Fixture Times - The menu provides readouts of fixture operation hours. Power On Time Hours - Select this menu to read the number of fixture operation hours. Total Hours - The item shows the total number of the operation hours since the Robin 300 LEDWash has been fabricated. Resetable Hours - The item shows the number of the operation hours that the Robin 300 LEDWash has been powered on since the counter was last reset.
6.3 Tab "Personality" User mode - The Robin 300 LEDWash allows you to recall up to 3 user settings. After switching the fixture on for the first time, the User A settings is active. Now all changes made in the “Personality” menu , ”Addressing” menu and the “Music Trigger“ and “ Preset Playback“ items from the “Stand-alone” menu are saved to the User A settings. If you now select the User B settings, from this moment the changes made in these menus will be saved to the User B settings.
Screen Settings - Use this menu to change the touch screen settings. Display Intensity - The item allows to control the intensity of the screen (1-min., 10-max.). Screen saver Delay - The item allows you to keep the screen on or to turn it off automatically after 1-10 minutes after last touch (or pressing any button on the control panel). Touchscreen Lock - The item allows you to lock the screen after last touch (or pressing any button on the control panel).
Music Trigger - Use the item to activate the sound control of the running program via the built-in microphone. Preset Playback - This menu allows you to select the program which will be played in a loop after switching the fixture on (the option is commonly used in a stand-alone operation without an external controller). None - The option disables “Presetting playback” function. Test - The option starts the test sequences. Prog. 1 - The option starts user program No. 1. Prog.
6.6 Tab "Service" Adjust DMX Values - The menu allows you to set all effects to desired positions before fine calibration of the effects . Calibrations - This menu enables fine calibration of fixture effects and download default calibration values. Calibrate Effects - The menu allows the fine adjustment of effects.
yourself and ask for help your ROBE distributor. Note 2: DMX address, IP address, programs 1-3 and all items in the menu "Personality" will be set to their default (factory) values. To update software in the fixture: I. Installation of the DMX Software Uploader. 1. DMX Software Uploader program is available from the ROBE web site at WWW.robe.cz. 2. Make a new directory ( e.g. Robe_Uploader) on your hard disk and download the software to it. 3. Unpack the program from the archive.
* SENSOR_VALUE DISPLAY_INVERT * * DISPLAY_LEVEL * * PAN_INVERT * * TILT_INVERT * * DEVICE_RESET * DMX_PERSONALITY * * DMX_PERSONALITY_DESCRIPTION * STATUS_MESSAGES * STATUS_ID_DESCRIPTION * DEVICE_HOURS * 2 8. Wireless DMX operation The wireless version of the Robin 300 LEDWash is equipped with the Lumen Radio CRMX module and antenna for receiving DMX signal. CRMX module operates on the 2.4 GHz band. To link the fixture with DMX transmitter.
10. Technical Specifications Electrical Power supply:.........................electronic auto-ranging Input voltage range:............... supply 100-240V, 50/60Hz Fuse:.......................................T3.15 A Mx. power consumption:..........200W/225 VA @230V, power factor=0.96 Optic Light source: 19 Cree MC-E RGBW LED multichips 3 LED zones with individual colour control of each Typical Lumen Maintenance: 70% @ 60,000 hours LED life expectancy: 60.
Support of RDM (Remote Device Management) 5 DMX modes (37, 21, 15, 10, 37 control channels) Wireless DMX/RDM module (only for Wireless DMX version) Compliance with USITT DMX-512 (1986 & 1990) and 512-A Full DMX fidelity and frame integrity Auto sensing of DMX frame rate and frame size <5ms DMX latency Operational frequency range of 2402-2480 MHz Producer: LumenRadio Connection DMX data in/out: Locking 3-pin and 5-pin XLR AC power input: 1.
Mounting adapter Accessories Mounting adapter (No.99013318).............1 piece Optional accessories Top hat -black (No.10980102) Top hat -white (No.10980104) EggCrate Robin 300 LEDWash-transparent (No. 1098 0115) 11. Maintenance and cleaning It is absolutely essential that the fixture is kept clean and that dust, dirt and smoke-fluid residues must not build up on or within the fixture. Otherwise, the fixture‘s light-output will be significantly reduced.
12.
