Version 1.
DigitalSpot 7000 DT Table of contents 1. Safety instructions ...................................................................................................................................................... 5 2. Unpacking ................................................................................................................................................................... 6 3. Introduction ......................................................................................................
DigitalSpot 7000 DT 20.1 Kaleidoscopic effect ..........................................................................................................................................36 20.2 Circular effect (Fish eye) ...................................................................................................................................38 20.3 RGB (CMY) effects.........................................................................................................................................
DigitalSpot 7000 DT 31.10 System restore ..............................................................................................................................................100 31.11 Cleaning ........................................................................................................................................................
DigitalSpot 7000 DT FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE POWERING OR INSTALLING YOUR DIGITALSPOT 7000 DT ! Save it for future reference. This device has left our premises in absolutely perfect condition. In order to maintain this condition and to ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written in this manual.
DigitalSpot 7000 DT When choosing the installation spot, please make sure that the device is not exposed to extreme heat, moisture or dust. Air vents and slots in the fixture´s head and base are provided for ventilation, to ensure reliable operation of the device and to protect it from overheating. The openings should never be covered with cloth or other materials, and never must be blocked. This fixture should not be placed in a built-in installation unless proper ventilation is provided.
DigitalSpot 7000 DT 3. Introduction The DigitalSpot 7000 DT features moving head with a video projection and automated lighting technologies including a DMX controllable digital media server installed in a fixture´s base. The built-in 32-bit Graphics Engine utilizes Linux and DirectX application programming interface to provide extensive image control of graphic objects.
DigitalSpot 7000 DT Rear panel of the fixture base 1 - DVI-I input (optional) - graph. engine 2 - VGA input (optional)- graph.engine 3 - 2x USB 4 - DMX output (5-pin XLR ) 5 - DMX input (5-pin XLR) 6 - ATX switch 7 - Fuse holder 8 - Power switch 9 - Power cord 10 - DMX input (3-pin XLR) 11 - DMX output (3-pin XLR) 12 - LAN (RJ-45) port 13 - VGA input-dataprojector 14 - S-video input-dataprojector 15 - S-video input - graph. engine 16 - Composite input - graph. engine 17 - SDI/ASI (optional) inputs-graph.
DigitalSpot 7000 DT 7. Shutting down the DigitalSpot 7000 DT There are two recommended ways how to shutdown the fixture: 1. A DMX controller can switch off the projector lamp and shut down the fixture with the "Lamp Off, Fixture Off" option on the control channel 8 (see DMX protocol). 2. The option "Fixture Off" in main menu of DigitalSpot 7000 DT switches off the projector´s lamp and shuts down the fixture.
DigitalSpot 7000 DT using the actual fixture in m before you permanently install it, so as to make allowance for this projector's optical characteristics. This will help you determine the exact mounting position so that it best suits your installation location 9.
DigitalSpot 7000 DT A pair of the Omega holders can be placed in 4 positions on the bottom of the base. Use 2 clamps (not supplied) with screws M12. To install the fixture on the truss: 1. Bolt clamp (1) to the omega holder (2) with M12 bolt and lock nut through the hole in the holder. 2. Fasten the omega holders on the bottom of the base by inserting both quick-lock fasteners (3) into the holes of the base and tighten fully clockwise. 3.
DigitalSpot 7000 DT 10. DMX 512 connection The fixture is equipped with both 3-pin and 5-pin XLR sockets for DMX input and output. Only use a shielded twisted-pair cable designed for RS-485 and 3-pin/5-pin XLR- connectors in order to connect the controller with the fixture or one fixture with another.
DigitalSpot 7000 DT The the DigitalSpot 7000 DT is equipped with 8-pin RJ- 45 socket for Ethernet input. Use a network cable category 5 (with four “twisted” wire pairs) and standard RJ-45 plugs in order to connect the fixture to the network.
DigitalSpot 7000 DT 12. Folder organization The library structure is reflected on the hard drive where all files for the library are stored. The whole library is contained within a special folder called ‘Media’. Inside the Media folder is a collection of folders (000,001...240) each named with a 3-digit number. Each folder following this convention represents a library folder and the 3-digit number represents the name of the folder. Because of this, you can’t have folders without the 3 digit number scheme.
DigitalSpot 7000 DT 13.
DigitalSpot 7000 DT Menu Level 1 Menu Level 2 Menu Level 3 Lamp Presetting Lamp On/Power On Lamp Off via DMX Lamp On If DMX is Present Display Adjusting Lamp Off if not DMX Display Permanent On Menu Level 4 Menu Level 5 On, Off On, Off On, Off On, Off Display Off After 5 min Permanent On Display Orientation Pan/Tilt Feedback On, Off Pan/Tilt Mode Time Mode Normal Orientation Rotated Orientation Speed Mode Active Blackout While: Projection Presetting During Movement Cor.
DigitalSpot 7000 DT Menu Level 1 Menu Level 2 Menu Level 3 Microphone Sensitivity 1..10..
DigitalSpot 7000 DT Menu Level 1 Menu Level 2 Menu Level 3 Music Trigger On, Off Play DMX Program DMX Program 1 in Loop Menu Level 4 Menu Level 5 Menu Level 6 Start Step 1-99 Save and Copy End Step 1-99 : Record DMX Program DMX Program 10 in Loop DMX Program 1 : DMX Program 10 Preset Playback Deactivated : Fixture Off Timer DMX Program 10 in Loop Timer Deactivated Timer Activated Set Timer Hours Set Timer Minutes Preview Mode Reset Functions Reset Graphics Engine Reset Pan/Tilt Syste
DigitalSpot 7000 DT Menu Level 1 Menu Level 2 Menu Level 3 Menu Level 4 Menu Level 5 Resetable Strikes Fixture Temperatures Current Projector temp. 1 Projector temp. 2 Projector temp. 3 Pan/Tilt Board Maximum Nonresetable LED Panel Board 1 LED Panel Board 2 Projector temp. 1 Projector temp. 2 Projector temp. 3 Pan/Tilt Board Maximum Resetable LED Panel Board 1 LED Panel Board 2 Projector temp. 1 Projector temp. 2 Projector temp.
DigitalSpot 7000 DT Menu Level 1 Menu Level 2 Menu Level 3 HTTP Access Set Account USB Data Synchronize Menu Level 4 Allow Anonymous Yes/No USB1 Open Menu Level 5 Menu Level 6 Menu Level 7 Menu Level 8 Media Open 000 Open USB2 : 240 Synchronize to Fixture Synchronize from Fixture Update Open Synchronize to Fixture Synchronize from Fixture Init Flash Disc Software Update Calibrate Values Update Graphical Software Update HW processors Software Update Media Content Analog Iris Calib.
DigitalSpot 7000 DT 14. Operating modes Before operating the DigitalSpot 7000 DT from a DMX 512 controller, you need to define the source of DMX data, which may be: DMX 512 - data is transmitted over standard DMX cables. Set a valid DMX start address, which is defined as the first channel from which the DigitalSpot 7000 DT will respond to the controller.
DigitalSpot 7000 DT 3. Press the [ENTER] to move on the second number of the IP address 4. Repeat steps 2 and 3 for the third and fourth number of the IP address. If you want to return back on the previously edited number, press [ESC]. The same way you can set the Netmask Address. Gateway Address –Option allows to set gateway address. Set ArtNet Universe - Select this submenu to set a Universe (0-15). The Universe is a single DMX 512 frame of 512 channels.
DigitalSpot 7000 DT Display Adjusting --- This function allows you to change the display settings: Display Permanent On - This function allows you to keep the display permanent on or to turn it off after 5 minutes of inactivity of control buttons (wheel) Display Orientation - Select this function to adjust the display orientation: Normal orientation - A standard display orientation. Rotated Orientation - Inverts the display by 180°.
DigitalSpot 7000 DT Alphabetical Order --- The media files are assigned to DMX values in an alphabetical order. Numerical projection --- The media files are assigned to DMX values in a numerical order. Microphone Sensitivity --- Select this item to adjust the microphone sensitivity from 1 (maximum) to 20 (minimum). Verbose Mode --- Use this menu to hide messages displayed on the screen when you are changing some setting on the Power/Special functions channel (e.g. Rear projection on, Rear projection off...
DigitalSpot 7000 DT The [RNS] encoder wheel controls movement between arrow fields on the control display and the [ENTER] button enables movement in menu.Pressing the [ENTER] on a circular field (marked "OK") confirms selected options. The [ESC] button-leaves menu without saving changes. 15.6 Stand-alone setting Use this menu to set options for a stand-alone mode as a selection of the program, programming and modifying user programs.
DigitalSpot 7000 DT Record DMX Program --- The menu allows to record DMX data that receives the fixture and then replay them again via the menu “Play DMX program”. There is a list of 10 programs for recording with unlimited steps each. Select desired program number and press the [ENTER] to enter the recording screen. The data record starts after changing any receiving DMX value. To stop recording, press [ENTER] or [ESC]. Recorded DMX program has the name dprg_xx.
DigitalSpot 7000 DT Lamp On Time --- Select this submenu to read the number of the operation hours with the projector lamp on. Total Hours - The function shows the total number of the operation hours with the lamp on since the DigitalSpot 7000 has been fabricated. Resetable Hours - The function shows the number of the operation hours with the lamp on that the DigitalSpot 7000 has been powered on since the counter was last reset. In order to reset this counter to 0, press [ENTER] twice.
DigitalSpot 7000 DT 300-max.size. Regenerate Thumbnails - By pressing the "Enter" button the refreshing process of gobo/video thumbnails starts. This action should be performed if you have changed gobo/video files and the fixture was not switched off after the change , otherwise the refreshing process runs automatically at starting up of the DigitalSpot 7000 DT.
DigitalSpot 7000 DT 4. If you want to copy all Media folder from the fixture (including subfolders 000-240), select item "Synchronize from Fixture". If you want to copy only one subfolder (e.g. 035) ,select "Open", press the [ENTER] , select desired subfolder from a list of subfolders ,press the [ENTER] and select option "Synchronize from Fixture". If you want to copy only one file, select "Open" and press Enter. Select the desired file, press the [ENTER] and confirm a question in a dialogue box.
DigitalSpot 7000 DT Setting all keystone values to 0 will place all four corners of the image at the four corners of the projector output. The keystone values can also be used to create interesting skewing effects. For the picture merging are important both the KeyStone X-ratio and KeyStoneY-ratio channels for correction of the image distortion caused by placing projectors at different distances from the final image.
DigitalSpot 7000 DT To adjust desired image shape you can use the following (keystone) parameters on the gobo layer 2: 1. Layer zoom in X and Y direction. The channels Gobo zoom X coarse and Gobo zoom X fine allow 8-bit/16-bit zooming in X-direction. The channels Gobo zoom Y coarse and Gobo zoom Y fine allow 8-bit/16-bit zooming in Y-direction. 2. Gobo position in X and Y direction. The channels Gobo position X coarse and Gobo position X fine allow 8-bit/16-bit positioning in X-direction.
DigitalSpot 7000 DT 3. Layer skewing along X and Y axis. On the channel Gobo effect 1 selection adjust a DMX value=150 and using the control parameters 1 an 2 you can skew the image in either X or Y axis. The channel Gobo effect 1 – Parameter 1 skews the image in X-axis. The channel Gobo effect 1 – Parameter 2 skews the image in Y-axis. 4. Layer Squeezing/Stretching along X and Y axis.
DigitalSpot 7000 DT On the channel Gobo effect 2 selection adjust a DMX value=150 and using the control parameters 1 you can squeeze the image in Y axis. Note. To allows this effect, the channel Gobo effect 1 selection has to be set to DMX=150. The channel Gobo effect 2 – Parameter 1 squeezes/stretches the image edges in X-axis. 5. Image X-ratio and Y-ratio. On the channel Gobo effect 2 selection adjust a DMX value=150 and the second and third parameter control image X-ratio and Y-ratio. Note.
DigitalSpot 7000 DT After shaping the image by means of the parameters stated above, you can apply the global banner effects on the whole graphics output and this final image should appear for instance like this: 17. In Frame and Out Frame parameters You can select any segment of a video file for playback by assigning parameters for In Frame (start point) and an Out Frame (end point) as pictured below.
DigitalSpot 7000 DT 3. It is possible to skip a segment in the video file by setting the In Frame to a point following the Out Frame value. 18. Video Control The channel Gobo control defines how the current layer will be ‘composed’ with the previous layers and the playback options in each mode .The Digital Spot 7000 supports the following options: Copy mode (0-17 DMX): In this mode, the pixels of the layer are written on top of the previous layers.
DigitalSpot 7000 DT 19. Playback speed The Playback speed channel controls the speed of video playback at selected playback options. Playback speed Meaning DMX value 0 or 128 Normal speed Plays back video files at the original record. speed 1-127 Slow speeds from slowest to normal Plays back video files at an increasing speed, from the slowest to the original recorded speed 129-255 Faster than normal to fastest Plays back video files at an increasing speed, from faster than normal to the fastest. 20.
DigitalSpot 7000 DT Isosceles triangular 104 105 Triangular 1 106 107 Triangular 2 108 109 DMX value Static mode Dynamic mode Mosaic effect Examples Centered Kaleidoscope (rough) 110 111 Note: As the effect does not cover all projection are, the image from the lower layer can be displayed at the sides of the effect. E.g. Centered Kaleidoscope effect has been selected on the layer 4 and the picture on the layer 3 is visible at the sides of the effect.
DigitalSpot 7000 DT Meaning of the control channels depends on the kaleidoscope mode which has been selected: Static mode.
DigitalSpot 7000 DT Parameter 1 Parameter 2 Parameter 3 Character of the circular effect X-ratio of the image Y-ratio of the image 0-255 concave (0) no adjustment (128) convex (255) 0-255 0-255 continual adjustment continual adjustment 20.3 RGB (CMY) effects The RGB effects section on the channel Gobo effect 2 selection allows to apply a variety of RGB colour swapping effects to graphic objects. RGB subtract All Pixels (DMX value=50) – the effect reduces colour values across all pixels.
DigitalSpot 7000 DT Swap RGB to RBG (DMX value=54) – the effect swaps green and blue colour in all pixels. Red colour remains without change. Associated control parameters: Control parameter Parameter 1 Controlled item Red colour element DMX value 0-255 Parameter 2 Green colour element 0-255 Parameter 3 Blue colour element 0-255 Function No change.
DigitalSpot 7000 DT Swap RGB to BGR (DMX value=58) – the effect swaps red and blue colour in all pixels. Green colour remains without change. Associated control parameters: Control parameter Parameter 1 Controlled item Function Red colour element DMX value 0-255 Parameter 2 Green colour element 0-255 No change.
DigitalSpot 7000 DT Colour to Alpha (DMX value=62) – the effect changes the transparency level of an image´s element colour values.
DigitalSpot 7000 DT Brightness scale (DMX value=69) – the effect changes the output intensity of brightness of the picture. Associated control parameters: Control parameter Parameter 1 Parameter 2 Controlled item Inclination of the conversion line – bottom point Inclination of the conversion line – top point DMX value Function 0-255 Changes the inclination of conversion line for output brightness from no adjustment (0 ) min.
DigitalSpot 7000 DT + Gobo effect selection on the layer 4: Gobo effect 1 selection =91 (the effected has been activated) Gobo effect 1- Parameter 1 = 158 (iris size) Gobo effect 1- Parameter 2 = 2 (iris type) Gobo effect 1- Parameter 3 = 5 (texture mode) Visual effect on the projection screen when the Iris Effect On Layer is activated: Below, there is a description of the Parameter 3 for each group of texture modes ( examples in the table are stated for X-axis only, but the Y-axis behaves in the same).
DigitalSpot 7000 DT 20-29 (Mode 3) 30-39 (Mode 4) The following modes (5-8) include black mask 40-49 Dimmer on the layer 3= 255 DMX Dimmer on the layer 3= 255 DMX Dimmer on the layer 3= 1 DMX Dimmer on the layer 3= 1 DMX (Mode 5) Parameter 3 DMX value (Mode) Zoom X Position X 50-59 (Mode 6) Dimmer on the layer 3= 255 DMX Dimmer on the layer 3= 255 DMX 45
DigitalSpot 7000 DT Dimmer on the layer 3= 1 DMX Dimmer on the layer 3= 1 DMX Dimmer on the layer 3= 255 DMX Dimmer on the layer 3= 255 DMX Dimmer on the layer 3= 1 DMX Dimmer on the layer 3= 1 DMX Dimmer on the layer 3= 255 DMX Dimmer on the layer 3= 255 DMX Dimmer on the layer 3= 1 DMX Dimmer on the layer 3= 1 DMX 60-69 (Mode 7) 70-79 (Mode 8) The iris effect can be combined together, e.g. between layers 4-3 and 3-2. 20.
DigitalSpot 7000 DT 255 Type of iris is changed after completing the open/close cycle The Parameter 3 allows to choose iris opening/closing command: DMX value Function 0 Close iris 1 Open iris 2 3 Open and close iris at gobo change Open iris at gobo change, close iris at gobo change A default value for all three parameters is 0. 20.
DigitalSpot 7000 DT Parameter 3 129-255 DMX -turning by 360° to the left Diagonal position: 0-255DMX – top left corner bottom right corner 128 DMX - center of image Original 128 P1=111DMX, P2=84DMX, P3=138DMX Example 2. Pixelation effect Activation channel Activation DMX value Control: Parameter 1 Parameter 2 Parameter 3 Gobo Effect 2 Selection (on each layer) 71 Amount of pixel in X-axis: 0-255DMX - max. min. Amount of pixel in Y-axis: 0-255DMX - max. min.
DigitalSpot 7000 DT Original P1=81DMX, P2=0DMX, P3=85DMX P1=81DMX, P2=128DMX, P3=85DMX Example 4. Posterization effect Activation channel Activation DMX value Control: Parameter 1 Parameter 2 Gobo Effect 2 Selection (on each layer) 73 Number of colours: 0 DMX - all colours 1-255DMX - reducing of colours Gamma correction: 0-255DMX - min. max. Original Default value 0 0 P1=228DMX, P2=0DMX Example 21. Media content management As you seen earlier in chapter "12.
DigitalSpot 7000 DT - how much content you want to move - whether the fixture is currently connected to the Ethernet fixture link There is several methods for moving user content files and folders between fixtures and a local drive and between fixtures each other.
DigitalSpot 7000 DT If all settings are proper, you will see "Media" and "Update" folders in the Windows explorer window and now you can work with them as local folders and files. See also "Special functions"--> "FTP Server". 2. FTP client in Mozilla Firefox If you use Mozilla Firefox as your web browser, you can install FTP client into the browser.
DigitalSpot 7000 DT To install FTP client for Mozilla Firefox on your computer. 1. Run Mozilla Firefox. 2.Select option “ Tools” from the Menu bar, select “Add-ons” item. 3.Select option “Get Add-ons” from the standard toolbar, type fireftp into the top left field and press Enter key. 4.Click on the Add to Firefox.. button and follow the installation instructions. 5. Follow the installation instructions until the installation has finished. 5.
DigitalSpot 7000 DT After installing FTP client, run Mozilla Firefox and type the IP address of desired fixture in ftp format e. g. ftp://2.97.181.89 and a Fire FTP window will appear. If you do not want to keep in mind IP addresses of all connected fixtures, you can use the Remote configuration program (by typing the IP address of one fixture to the web browser in http format e. g. http://2.97.181.89) and go to the Contents Synchronization window where a list of available fixtures is offered.
DigitalSpot 7000 DT 21.2 Moving files between networked fixtures The option "Contents Synchronization" in a "Remote control program" running on your PC offers easy control of file transfer between networked fixtures via web browser. (For detail description of the Remote configuration program see chapter "Remote control of the fixture via web browser" below). A window of the Contents Synchronization: There is a list of available fixtures under Device Available for Update.
DigitalSpot 7000 DT 22. Remote control of the fixture via WWW browser The DigitalSpot 7000 DT offers a remote control of the fixture and diplaying useful information about the fixture including the gobo folders contents via www browser. The fixtures has to be connected via an ethernet (with Art-Net communication protocol) to a network. The PC or light console has to be connected to the same network as the fixtures. Use only the IP addresses which have first number 2 like 2.X.X.X, e.g. 2.236.2.88.
DigitalSpot 7000 DT Status Messages -the window under this option displays error and status messages. Special Functions - the window offers several items: "Thumbnails size" - changing the size of the thumbnails. The change takes effect in the item "Content". If you change the thumbnail size, use the button "Update" below the size box. "Log File" - enables to generate log file for service purposes.
DigitalSpot 7000 DT Content - by entering this window a complete overview of all gobo folders is offered, from which the folder to be view can be selected.Click a desired folder to display its content. Click a desired picture to zoom it in. Contents Synchronization - the window allows you copy (addition) media content from a current fixture to another fixtures on an ethernet network. There is a list of available fixtures under Device Available for Update.
DigitalSpot 7000 DT Remote Graphics Output - preview of the current projecting output. Remote RNS Display - the window "takes" the fixture´s control panel. You can browse and adjust all items in this fixture menu by means of your keyboard. Use the Up/Down and Enter/Escape keys. Remote Content - the window offers a table for definition of streaming sources. Type a streaming protocol, an IP address and a port number for the desired streaming source (e.g.
DigitalSpot 7000 DT To end the Remote control program, close WWW browser ( or use option "Logout" if you entered the program using the user name and password). 23. Picture merging The picture merging system allows to create a panoramic projection controlled from a light DMX console. The resulting seamless image consists of the images of the individual projectors. It is possible to create an image field up to 64 segments (non-mirrored configuration).
DigitalSpot 7000 DT Global effect 1- Parameter 1 The DMX value from the range of 1- 235 allows selection of desired image field configuration according to the tables on the following pages.
DigitalSpot 7000 DT DMX value Image field Configuration WxH Total number of fixtures DMX value Image field Configuration WxH Total number of fixtures 37 1x7 7 92 11 x 1 11 38 7x2 14 93 2 x 11 22 39 2x7 14 94 11 x 3 33 40 7x3 21 95 3 x 11 33 41 3x7 21 96 11 x 4 44 42 7x4 28 97 4 x 11 44 43 4x7 28 98 11 x 5 55 44 7x5 35 99 5 x 11 55 45 5x7 35 100 12 x 1 12 46 7x6 42 101 1 x 12 12 47 6x7 42 102 12 x 2 24 48 7 x7 49 103 2 x 12 24 49
DigitalSpot 7000 DT Horizontally mirrored configuration DMX value Image field configuration of base matrix WxH Total number of fixtures in base matrix DMX value Image field configuration of base matrix WxH Total number of fixtures in base matrix 128 2x1 2 146 10 x 2 20 129 4x1 4 147 4x5 20 130 2x2 4 148 10 x 3 30 131 4x2 8 149 6x5 30 132 6x1 6 150 10 x 4 40 133 2x3 6 151 8x5 40 134 6x2 12 152 10 x 5 50 135 4x3 12 153 12 x 1 12 136 6x3 18 154 2x6 12
DigitalSpot 7000 DT Vertically mirrored configuration DMX value Image field configuration of base matrix WxH Total number of fixtures in base matrix DMX value Image field configuration of base matrix WxH Total number of fixtures in base matrix 164 1x2 2 182 5x4 20 165 2x2 4 183 2 x 10 20 166 1x4 4 184 5x6 30 167 2x4 8 185 3 x 10 30 168 3x2 6 186 5x8 40 169 1x6 6 187 4 x 10 40 170 3x4 12 188 5 x 10 50 171 2x6 12 189 6x2 12 172 3x6 18 190 1 x 12 12 1
DigitalSpot 7000 DT Vertically and horizontally mirrored configuration DMX value Image field configuration of base matrix WxH Total number of fixtures in base matrix DMX value Image field configuration of base matrix WxH Total number of fixtures in base matrix 200 2x2 4 218 10 x 4 40 201 4x2 8 219 4 x 10 40 202 2x4 8 220 10 x 6 60 203 4x4 16 221 6 x 10 60 204 6x2 12 222 10 x 8 80 205 2x6 12 223 8 x 10 80 206 6x4 24 224 10 x 10 100 207 4x6 24 225 12 x 2 24
DigitalSpot 7000 DT The mirrored image configurations bring 2 advantages: 1. Resolution of the source image and merged images on the wall is the same in comparison with non-mirrored configuration (if you use suitable mirrored configuration – see example 3 below). 2. By using the picture merging with mirrored configuration you can cover any size of projection area. The total number of used projectors is unlimited. Examples: 4 DigitalSpots 7000DT are used in the picture merging.
DigitalSpot 7000 DT Global effect 1- Parameter 2 The DMX values from the range of 0-255 are used to step segment by segment throw the image grid. The DMX value of 0 corresponds to the upper left segment of the image grid. The stepping runs from the left to the right and down from top (see example for field 8x3 segments bellow). Global effect 1- Parameter 3 This channel enables to transform displaying of the segment edges-sharp or blended edges.
DigitalSpot 7000 DT Global effect 2 A DMX value of 20 enables fine adjusting of the red, green and blue gamma curve at overlaping edges to achieve consistent colour (brightness) of these parts of image. Note. After selecting desired image segment for the gamma correction (by means of the Global effect 1 Parameter 2), set the channel Global effect 1 - Parameter 3 to 0 in order to display blended edges of the picture segment.
DigitalSpot 7000 DT 24. Pre-cut content mode for Picture Merging The mode is useful when you want to cover large projection area with full resolution for each projector or you don't want to be restricted with limits of matrix configuration. The basic idea is that before projection you have to prepare the pre-cut content (e.g. picture) and upload the single parts of the splitted source picture into individual fixtures.
DigitalSpot 7000 DT Size of segments in X-axis: LpartX = LtotalX/[x-(b/100)*(x-1)] LpartX =1024/ [3-(10/100)*(3-1)] the size of overlapping edges was selected 10% (b=10) LpartX = 366 pixels Since the size of the segments in Y-axis is the same as at the source picture, each of the 3 fixtures will project picture with resolution of 366x768 pixels. ___________________________________________________________________________________________ Note.
DigitalSpot 7000 DT 25. Effect video synchronization The synchronization option can be set separately for each gobo layer (channels Synchronization to ID). The fixture synchronization acts with the fixture ID which is defined as the last number of fixture´s IP address. This fixture ID is shown on the fixture´s display. The fixtures are synchronized to the one fixture - named a master fixture.
DigitalSpot 7000 DT 26. Projection onto angular, cylindric or spheric surfaces If a projection on curved surface is required a correction of the shape distortions is necessary. The DigitalSpot 7000 DT supports projection onto angular screens, cylinders and spheres. 26.1 Curved surface support channels Global effect 2 This channel enables you to select desired shape of the surface: To simplify a correction process, there is a gobo with a net pattern (DMX value = 2) in a factory folder No.
DigitalSpot 7000 DT Global effect 2- parameter 2 This parameter enables to adjust the horizontal length of the edge. A DMX Value of 128 = no adjustment, values below 128 move the edge to the left, values above 128 move the edge to the right. Global effect 2- parameter 3 This parameter enables to adjust the vertical length of the edge. A DMX Value of 128 = no adjustment, values below 128 move the edge downwards, values above 128 move the edge upwards.
DigitalSpot 7000 DT Note: If a projection of rectangle (square) on a circle (sphere) is selected on the channel Global Effect 2 (DMX value of 10 or 11), the meaning of the Keystone parameters in a DMX chart will be changed as follows: Channel Type of control DMX value Function 0 -127 128 129-255 Image moving in an X-direction Moving the image from left to center Center Moving the image from center to right proportional step proportional 0 -127 128 129-255 Image moving in a Y-direction Moving the imag
DigitalSpot 7000 DT 27. Video processing on gobo layers from a streaming video server A streaming video is a video that is continuously sent by one device (e.g. PC) and received by another device (DigitalSpot 7000 DT) over an ethernet network. 1. TightVNC client The TightVNC is a free remote control software package available at http://www.tightvnc.com/download.php . With TightVNC, you can see the image output of the DigitalSpot 3500 DT and edit it with your local PC which has TightVNC server installed.
DigitalSpot 7000 DT 4.Switch off the Firewall on the PC, where the TightVNC server is installed. Hire is an example for Windows XP: 5. Run a Remote control by means of WWW browser at your PC, select option “Remote content” and write IP address of TightVNC server to the Source Address line in the following format : vnc:// xxx.xxx.xxx (e.g. vnc://2.1.1.12). 2. Streaming video server The Streaming video software stated on the pictures below is available at http://www.videolan.org/vlc/.
DigitalSpot 7000 DT - Click on the "Properties" button and the following window will open. - Click on the item "Internet Protocol (TCP/IP)" and the Internet Protocol Properties window will open. Set IP address to something like 2.X.X.X with an IP mask of 255.0.0.
DigitalSpot 7000 DT 3. Install a VLC media player. - click on a VLC media player self-extracting package located on the hard disk and follow the on-screen instructions. After installing it, run this VLC media player. In a horizontal menu "File" click on "Open" and the following window will open. Type the name of video file in the "Open" field, check the "Stream/Save" option and click the "Settings" button.
DigitalSpot 7000 DT Check the "HTTP" option in a Outputs column, type an IP address of the PC in the "Address" field and a figure port in the "port" field. Note: If you want to run more videos on this PC, you have to run the VLC media player for each video and every media player has to have a different figure of the port but the IP address will be the same. Select the MPGTS or MPEGPS option in the "Encapsulation method" row. Check the "Video codec" option and select mp2v.
DigitalSpot 7000 DT A different setting of VLC media player for streaming of the PC desktop is required. Type the following line in the "Customize" field of the Open window: screen:// screen-fps=10 :screen-caching=100 Space The Stream output window has the same setting like for video streaming except the field "Bitrate (kb/s)" which should be set at the value of 8192. Important: The Playback speed channel at corresponding gobo layer should be set at a DMX value of 150-200.
DigitalSpot 7000 DT Type the IP address of the DigitalSpot 7000 DT which is to project data from a remote streaming video source in your WWW browser to run the Remote Control program. Select the option "Remote Content" and the following window will open: Type in the "source Address" field the IP address and the port number of the streaming source (in our case it is a PC) in this format: http://2.x.x.x:port number e.g. http://2.1.1.3:1234 and save it by clicking the "Update" button.
DigitalSpot 7000 DT Fixture linkage: 28. RDM This fixture is ready for RDM operation.RDM (Remote Device Management) is a bi-directional communications protocol for use in DMX512 control systems, it is the new open standard for DMX512 device configuration and status monitoring. The RDM protocol allows data packets to be inserted into a DMX512 data stream without adversely affecting existing non-RDM equipment.
DigitalSpot 7000 DT 28.1 CITP/MSEX protocol The fixture also supports CITP/MSEX protocol. It is an open protocol for integration of lighting controllers, media servers and visualizers on a higher-than-control level. It makes it possible to browse a media server with thumbnail previews of content as well as effects, to use the correct effect-specific parameter names while programming and to preview output from a controller or visualizer.
DigitalSpot 7000 DT 29. Technical specifications Electrical specifications Auto-switching power supply Input voltage range: 100-120V/ 200-240V AC, 50/60 Hz Max. Pover Consumption @ 230V: 780W (800VA), I=3.3A Power factor: 0.96 Projector Specifications Model:PLC-XP100L Light output:6,500 ANSI lumens Lamp:330 W NSHA Rated lamp life: 3,000 h (eco mode); 2,000 h (normal mode) Throw distance ratio: 1.8-2.4 : 1 (standard) Contrast ratio:2000:1 LCD panel system:1.
DigitalSpot 7000 DT Electromechanical Effects Zoom Focus Mechanical iris Control 5“ TFT LCD display & Robe navigation system Web access for total control of fixture (user library management) Media Content Synchronization in web interface Protocol USITT DMX 512 169 control channels max.
DigitalSpot 7000 DT Accessories Omega holder (No.99010420)....................................2 pieces USB 2.0 flash drive with a System recovery utility......1 piece Optional Accessories VGA/DVI capture card set (P.N. 99013317) – includes capture card DVI/VGA Unigraph and mounting accessories SDI/ASI capture card set (P.N. 99012445) – includes capture card SDI/ASI DTA-145-SDP and mounting accessories Air filter for DS 7000 DT, PLC-XP100L (P.N. 17030507) Long throw optics 2.7 – 3.5 : 1 (P.N.
DigitalSpot 7000 DT Illuminance/Image size chart for Long Throw Optics (throw distance ratio 2.7 - 3.
DigitalSpot 7000 DT Illuminance/Image size chart for Short Throw Optics (throw distance ratio 1.2 - 1.
DigitalSpot 7000 DT 30. Error and information messages The warning icon (triangle) on the bottom-right side of the fixture´s screen indicates some error or information message which appears on the screen by pressing the [ESC] button. Pan Error The message will appear after the reset of the fixture if the yoke´s magnetic-indexing circuit malfunctions (sensor failed or magnet is missing) or the stepping motor is defective or its driving IC3 on the PCB in the fixture base.
DigitalSpot 7000 DT LED Temperature Sensor 2 Short The message informs you that there is not communication between the sensor measuring the temperature of the LED module 2 and the control PCB. This connection is in short circuit. Dataprojector Temp. Read Error System message from dataprojector. Dataprojector Power Failure System message from dataprojector. Dataprojector Abnormal Temperature System message from dataprojector. Dataprojector Lamp Failure System message from dataprojector.
DigitalSpot 7000 DT 31. Maintenance 31.1 Replacing the lamp Turn the power off and disconnect the fixture from the mains. If the lamp is hot, avoid burns by waiting for approximately 45 minutes until the lamp has cooled. 1. Use the tilt lock button (2) to secure the moving head in a horizontal position. If you look at the rear cover of the head, the warning writings has to be in a readable position 2. Remove the rear plastic cover (1) of the head by loosening the four quarter-turn fasteners (2).
DigitalSpot 7000 DT 31.2 Replacing the projector If you need to remove the data projector, turn the power off and disconnect the DigitalSpot 7000 DT from the mains. If the projector lamp is on, wait 25 minutes until the projector has cooled. 1. Use the tilt lock button to secure the moving head in a horizontal position.If you look at the rear cover of the head, the warning writings has to be in a readable position. 2.
DigitalSpot 7000 DT 8. Unscrew the three covers (9), (10), (11) from the pro projector housing . 31.3 Accessing to the projector control buttons If you need to use the projector control buttons which are situated at the side of the projector, move the fixture head to the horizontal position as figured on the picture below (if you look at the rear cover of the head, the warning writings has to be in a readable position), and remove the side plastic cover by loosening the 4 screws. 31.
DigitalSpot 7000 DT 31.5 Installing the SDI/ASI capture card To install the optionsl SDI/ASI capture card. 1. Disconnect the fixture from power. 2. Remove both top covers (1) of the fixture base by unscrewing 14 screws (2). 3. Remove the cover plate (6) of an unused slots for SDI/ASI connectors on the rear panel of the fixture by unscrewing the 2 screws (5) M3x6. 4. Unscrew six fastening screws (4) and carefully tilt the rear panel from the chassis. 5.
DigitalSpot 7000 DT 6. Snap the two insulating washers with outer diameter of 10mm (10) into SDI/ASI connectors holder (8) and fasten this holder on the rear panel (3) with two screws M3x10 (9). The SDI/ASI cables (11) have to aim at the bottom of the fixture base. Keep right order of the insulating (13) and metal (14) washers on the screws (9) and tighten the nuts (15). Warning: The SDI/ASI connectors holder has to be electrically insulated from the rear panel otherwise the capture card can be damaged.
DigitalSpot 7000 DT 9. Remove the capture card from its packaging and gently press it down into the empty PCI slot. Secure the bracket of the card to the chassis by means of the screw (20) with M3 thread. Screw the supporting spacer holder (16) back to the chassis 10. Connect the SDI/ASI cables to the capture card. The IN/OUT cable has a blue sleeve at BNC connector and the OUT cable has a red one. BNC sockets on the capture card are marked (OUT) and (IN/OUT). 11.
DigitalSpot 7000 DT 31.6 Installing the optional optics To install the long throw optics (or short throw optics) follow the steps: 1. Disconnect the DigitalSpot 7000 DT from power. 2. Remove the front cover of the fixture head (2) by loosening the 4 quarter-turn fasteners (1). 3. Remove the module of the glass cover (4) by loosening the three quarter-turn fasteners (3). 4.
DigitalSpot 7000 DT 31.7 Replacing the fixture air filters Important! Check the air filters periodically and clean before they become clogged! Clean the air filters with a vacuum cleaner or you can wash them and put back dry. Replacing air filters in the fixture head. 1. Disconnect the fixture from power. 2. Raise up the filter cover (fixed by two magnets) on the head cover. 3. Pull the air filter out. 4. Clean or replace the air filter. 5. Snap the filter cover back to the head cover. 6.
DigitalSpot 7000 DT 31.8 Replacing the filter cartridge in the projector. 1. Turn off the DigitalSpot 7000 DT and unplug the AC power cord from the AC outlet. 2. Remove the projector from the fixture chassis as described in the chapter Replacing the projector. 3. Press on the filter cover to release the latch and open the filter cover. 4. Pull out the filter cartridge. When taking out the filter cartridge, put your finger on the filter cartridge’s tab and then pull. 5.
DigitalSpot 7000 DT 2. Use the Point buttons to move the red frame pointer to Filter counter and then press the SELECT button. A dialog box appears showing the Used time option and the Scrolls remaining option. Use the Point buttons to select Used time. 3. Used time shows the total accumulated time of the filter use, a timer setting option, and the Reset option. Select Reset and the “Filter counter Reset?” appears. Select [Yes] to continue. 4.
DigitalSpot 7000 DT 31.9 Replacing the fuse Only replace the fuse by a fuse of same type and rating. Before replacing the fuse, turn the power off and unplug the mains lead. Procedure: 1) Unscrew the fuse holder on the rear panel of the base with a fitting screwdriver from the housing (anti - clockwise). 2) Remove the old fuse from the fuse holder. 3) Install the new fuse in the fuse holder. 4) Replace the fuse holder in the housing and fix it. 31.
DigitalSpot 7000 DT 31.11 Cleaning Turn the power off and disconnect the fixture from the mains before starting cleaning procedure. It is absolutely essential that the fixture is kept clean and that dust, dirt and smoke-fluid residues must not build up on or within the fixture. Otherwise, the fixture‘s light-output will be significantly reduced. Regular cleaning will not only ensure the maximum light-output, but will also allow the fixture to function reliably throughout its life.
DMX protocol DigitalSpot 7000 DT - DMX protocol v. 1.7, DMX DMX Value Channel 1 0-255 2 0-255 3 0-255 4 0-255 5 0 1-255 1-255 6 0-9 10-31 32-63 64-95 96-127 128-159 160-191 192-223 224-255 7 0 1-127 128-129 130-255 8 0-39 April 5, 2012 Function Pan Pan movement by 530° Pan Fine Fine control of pan movement Tilt Tilt movement by 280° Tilt Fine Fine control of tilt movement Pan/Tilt speed,Pan/Tilt time Max.speed (tracking mode) P./T. speed-set Speed Mode in menu: Pan/Tilt Mode Speed from max. to min.
DMX protocol DMX DMX Value Channel 8 130-139 140-149 150-179 180-189 190-199 200-209 210-215 216-229 230-239 240-249 250-255 9 0-63 64-127 128-191 192-255 10 0-255 11 0-255 12 0 1-255 13 0-255 14 0-255 15 0-255 16 0-255 17 0-255 18 0-255 19 0-255 20 0-255 21 0-31 32-63 64-95 96-127 128-143 144-159 160-191 192-223 Function Type of control To activate following functions,hold DMX value 3 seconds Lamp On Pan/Tilt reset Reserved Zoom/Focus reset Mechanical iris reset Total reset Graphic engine reset/softwar
DMX protocol DMX DMX Value Function Channel 224-255 Shutter open LED Dimmer 22 0-255 Led module dimmer intensity 0 --> 100 % Common digital effects for all gobo layers KeyStone Top Left X 23 0-255 Move top left corner X value to center (0-default) KeyStone Top Left Y 24 0-255 Move top left corner Y value to center (0-default) KeyStone Top Right X 25 0-255 Move top right corner X value to center (0-default) KeyStone Top Right Y 26 0-255 Move top right corner Y value to center (0-default) KeyStoneBottom Right
DMX protocol DMX DMX Value Channel : 255 37 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 27 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 Function : 2500 K Digital Iris-type selection Circular ,outside-->in,sharp edge Circular ,outside-->in,fuzzy edge 1 Circular ,outside-->in,fuzzy edge 2 Circular ,outside-->in,fuzzy edge 3 Circular ,outside-->in,fuzzy edge 4 (maximum) Circular ,inside-->out,sharp edge Circular ,inside-->out,fuzzy edge 1 Circular ,inside-->out,fuzzy edg
DMX protocol DMX DMX Value Channel 47 37 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 Function Wedge wipe ,bottom-->up, fuzzy edge 2 Wedge wipe,bottom-->up, fuzzy edge 3 Wedge wipe,bottom-->up, fuzzy edge 4 (maximum) Radial wipe ,left -->bottom,sharp edge Radial wipe ,left -->bottom,fuzzy edge 1 Radial wipe ,left -->bottom,fuzzy edge 2 Radial wipe ,left -->bottom,fuzzy edge 3 Radial wipe ,left -->bottom,fu
DMX protocol DMX DMX Value Channel 97 37 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 Function Horizontal two-way band wipe,bottom left-->top right Vertical one-way band wipe,top left-->bottom right Vertical one-way band wipe,bottom right-->top left Vertical one-way band wipe,bottom left-->top right Vertical one-way band wipe,top right-->bottom left Vertical t
DMX protocol DMX DMX Value Channel 147 37 148 149 150 151 152 153 154 155 156 157 158 159 160 161-169 170 171 172 173 174 175 176 177 178 179 180-255 38 0 1-254 255 39 0-255 40 0 - 30 31 - 80 81 - 110 111 - 140 141 - 149 150 - 154 155 - 159 160 - 164 165 - 169 170 - 189 190-194 195-199 200 - 204 205-209 210-244 245-255 41 Function 2 diagonal curtains, top left-->center<-- bottom right Grid wipe 8x8,bottom right-->top left Grid wipe 8x8,bottom right-->top left,inverse Grid wipe 8x8,top right-->bottom left G
DMX protocol DMX DMX Value Channel 0-255 42 0-255 43 0-255 44 0-255 45 0-255 46 0-255 47 0-255 48 0-255 49 0-255 50 0 Function Positioning from left to right (0-default) Banner left rotation Rotation +/- 45° (128-default) Banner right positioning Positioning from right to left (0-default) Banner right rotation Rotation +/- 45° (128-default) Banner top positioning Positioning from top to bottom (0-default) Banner top rotation Rotation +/- 45° (128-default) Banner bottom positioning Positioning from bottom t
DMX protocol DMX DMX Value Channel 53 0-170 171-180 181-255 54 0 1 2 3 4 5 6 7 8 9 10 11 12 13-19 20 Function Global effect 1- Parameter 3 Segment edge display for Pixture merging Showing aspect ratio of image projected on the wall Reserved Global Effect 2 None Vertical inside corner mapping Vertical outside corner mapping Horizontal inside corner mapping Horizontal outside corner mapping Vertical convex cylinder mapping Vertical concave cylinder mapping Horizontal convex cylinder mapping Horizontal concav
DMX protocol DMX DMX Value Function Type of control Channel 121-140 Reserved If Grabber Card is installed in the fixture 141-160 VGA input of DVI/VGA grabber card step 161-180 DVI-I input of DVI/VGA grabber card step 181-200 SDI input of SDI/ASI grabber card step 201-220 ASI input of SDI/ASI grabber card step 221-255 Reserved 61 In Frame High 0-255 Defines the beginning of a media file segment as a proportional percentage of the movie length (0-default) In Frame Low 62 0-255 Defines the beginning of a media
DMX protocol DMX DMX Value Function Channel 27 Scrub (Display) the selected Out Frame 28-29 Reserved Video stream 2: 30-37 The same functionality as for Video stream 1 38-39 Reserved Substraction mode Video stream 1: 65 40 Play forward if dimmer (on layer 1) > 0, looping continuously 41 Play forward if dimmer (on layer 1) > 0, hold on last frame 42 Pause 43 Play forward in continuous loop 44 Play forward once and hold on the last frame 45 No function 46 Scrub (Display) the selected In Frame 47 Scrub (Displa
DMX protocol DMX DMX Value Channel 101 102 103 104 105 106 107 108-109 110-117 118-255 66 0 1-127 128 129-255 67 0-63 64-127 128 129-192 193-255 68 0-255 69 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Function Play forward if dimmer (on layer 1) > 0, hold on last frame Pause Play forward in continuous loop Play forward once and hold on the last frame No function Scrub (Display) the selected In Frame Scrub (Display) the selected Out Frame Reserved Video stream 2: The same functionality
DMX protocol DMX DMX Value Channel 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 69 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 69 63 64 65 66 67 68 69 70 71 72 73 74 Function X inv. y rotate Tile xy Tile xy XYZ rot. cube XYZ rot. sphere X rot. cylinder Y rot.
DMX protocol DMX DMX Value Channel 75 76 77 78-79 80 81 82 83 84 85 86 87-89 90 Function Gobo disc mirror X Gobo disc mirror Y Gobo disc mirror XY Reserved Plane mirror X top inverse Plane mirror X bottom inverse Plane mirror Y left inverse Plane mirror Y right inverse Plane mirror XY inverse Plane mirror X-inverse,Y Plane mirror X,Y-inverse Reserved Circular effect (Fish eye) Type of control none none none none none none none none none none P1, P2, P3 P1-character, P2-X ratio, P3-Y ratio 91 Iris on la
DMX protocol DMX DMX Value Channel 0-255 73 0 1 2 73 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 73 21 22 23 24 25 26 27 28 29 30 31 32 33-39 40 41 42 43 44 45-49 50 51 52 53 54 55 56 Function Effect control Gobo effect 2 Selection No effect Colour to black and white Colour to black and white inverse Black and white to black and white inverse Inversion Black Mask Black Mask inverse Contrast Brightness RGB to GBR RGB to BRG RGB to RBG Black and white to black and white inverse timed Colour to black and w
DMX protocol DMX DMX Value Channel 57 58 59 60 61 62 63 64-67 68 69 70 Function Swap RGB to BRG Swap RGB to BGR RGB invert Invert and swap RGB to BRG Invert and swap RGB to GBR Colour to Alpha Colour to Alpha inverted Reserved RGB scale P1-red, P2-green, P3-blue Brightness scale P1, P2 - inclination of conversion line Swirl effect Type of control P1, P2, P3 P1, P2, P3 P1, P2, P3 P1, P2, P3 P1, P2, P3 P1, P2, P3 P1, P2, P3 P1, P2, P3 P1, P2, P3 P1, P2 P1, P2, P3 P1-radius, P2-angle, P3-diagonal position
DMX protocol DMX DMX Value Channel 0-255 81 0-127 128 129-255 82 0-255 83 0-127 128 129-255 84 0-255 85 0 1-255 86 0-255 87 0-20 21-240 241-250 251 252 253-255 88 0 1-255 0 1-20 21-40 21-60 61-80 81-100 101-120 121-140 141-160 161-180 181-200 201-220 221-255 89 0-255 Function Position Y fine Gobo zoom X coarse Narrowing Centre (128-default) Widening Type of control proportional proportional step proportional Gobo zoom X fine Zoom X fine proportional Gobo zoom Y coarse Narrowing Centre (128-default) Wid
DMX protocol DMX DMX Value Function Channel In Frame Low 90 0-255 Defines the beginning of a media file segment as a percentage of the movie length (0-default) Out Frame High 91 0-255 Defines the end of a media file segment as a percentage of the movie length (255-default) Out Frame Low 92 0-255 Defines the beginning of a media file segment as a percentage of the movie length (255-default) 93 93 Type of control proportional proportional proportional Gobo control Copy mode Video stream 1 0 1 2 3 4 5 6
DMX protocol DMX DMX Value Channel 43 44 45 46 47 48-49 50-57 58-59 60 61 62 63 64 65 66 67 68-69 70-77 78-79 93 80 81 82 83 84 85 86 87 88-89 90-97 98-99 100 101 102 103 104 105 106 107 108-109 Function Type of control Play forward in continuous loop Play forward once and hold on the last frame No function Scrub (Display) the selected In Frame Scrub (Display) the selected Out Frame Reserved Video Stream 2 the same functionality as for Video stream 1 Reserved Multiplication mode Video stream 1 step
DMX protocol DMX DMX Value Channel 118-255 94 0 1-127 128 129-255 95 0-63 64-127 128 129-192 193-255 96 0-255 97 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 Function Reserved Playback Speed Normal Speed Slow speeds from slowest ---> normal Normal Speed Faster than Normal ---> Fastest Gobo rotation and indexing Clockwise rotation from fast to slow Indexing No rotation-centre (128-default) Indexing Anticlockwise rotation from slow to fast Gobo fine indexing
DMX protocol DMX DMX Value Channel 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 97 68 69 70 71 72 73 74 75 76 77 78-79 80 81 82 83 84 85 Function Squeeze out Bend X Bend Y Tile frame Frame Plane Flip X Plane Flip Y Plane Flip XY Plane mirror X top Plane mirror X bottom Plane mirror Y left Plane mirror Y right Plane mirror XY segment 1 Plane mirror XY segment 2 Plane mirror XY segment 3 Plane mirror XY segment 4 Plane tile 2x Plane tile 3x Plane tile 4x
DMX protocol DMX DMX Value Function Channel 86 Plane mirror X,Y-inverse 87-89 Reserved 90 Circular effect (Fish eye) Type of control none P1, P2, P3 P1-character, P2-X ratio, P3-Y ratio 91 Iris on layer P1, P2, P3 P1-size, P2-iris type, P3-texture mode 92 Auto Iris effect on layer P1, P2, P3 P1-speed, P2-mask type, P3-opening/closing command 93-94 95 Reserved Zoom In/Move XY P1, P2, P3 P1-zoom, P2-X-movement, P3-Y-movement 96 Zoom In/Auto Move XY P1, P2, P3 P1-zoom, P2-X-speed, P3- Y-speed
DMX protocol DMX DMX Value Channel 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 101 24 25 26 27 28 29 30 31 32 33-39 40 41 42 43 44 45-49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64-67 68 Function Brightness RGB to GBR RGB to BRG RGB to RBG Black and white to black and white inverse timed Colour to black and white timed Colour to inverse timed Cycle Cycle inverse Reserved Reserved Colour Key Colour Key inverse Key Black Key Black inverse Key White Key White inverse White flash Black flash Alpha flash Inv
DMX protocol DMX DMX Value Function Channel 69 Brightness scale P1, P2 - inclination of conversion line 70 Swirl effect Type of control P1, P2 P1, P2, P3 P1-radius, P2-angle, P3-diagonal position 71 Pixelation effect P1, P2, P3 P1-num. of pixels (X), P2-num.
DMX protocol DMX DMX Value Channel 129-255 112 0-255 113 0 1-255 114 0-255 115 0-20 21-240 241-250 251 252 253-255 116 0 1-255 0 1-20 21-40 21-60 61-80 81-100 101-120 121-140 141-160 161-180 181-200 201-220 221-255 117 0-255 118 0-255 119 0-255 120 0-255 121 Function Type of control Widening proportional Gobo zoom Y fine Zoom Y fine proportional Synchronization to ID No function step Synchronization to fixture ID proportional Gobo layer 3 Dimmer Dimmer intensity from 0% to 100% (255-default) proportional
DMX protocol DMX DMX Value Channel 0 1 2 3 4 5 6 7 8-9 Function Play forward if dimmer (on layer 3) > 0, looping continuously Play forward if dimmer (on layer 3) > 0, hold on last frame Pause Play forward in continuous loop Play forward once and hold on the last frame No function Scrub (Display) the selected In Frame Scrub (Display) the selected Out Frame Reserved Video stream 2 ( the same functionality as for Video stream 1): 10 11 12 13 14 15 16 17 18-19 Play forward if dimmer (on layer 3) > 0, loopin
DMX protocol DMX DMX Value Channel 61 62 63 64 65 66 67 68-69 70-77 78-79 121 80 81 82 83 84 85 86 87 88-89 90-97 98-99 100 101 102 103 104 105 106 107 108-109 110-117 118-255 122 0 1-127 128 129-255 123 0-63 64-127 128 129-192 193-255 Function Play forward if dimmer (on layer 3) > 0, hold on last frame Pause Play forward in continuous loop Play forward once and hold on the last frame No function Scrub (Display) the selected In Frame Scrub (Display) the selected Out Frame Reserved Video Stream 2 the sa
DMX protocol DMX DMX Value Channel 124 0-255 125 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 125 40 41 42 43 44 45 46 Function Gobo fine indexing (rotation) Fine indexing (rotation) Gobo effect 1 Selection No effect Zoom sinus Zoom bump in fade out Zoom fade in bump out Reserved Zoom in fade Zoom out fade Scale xy sinus Reserved Reserved Reserved XY pos. circle counter-clockwise XY pos. circle clockwise XY pos. scroll up XY pos.
DMX protocol DMX DMX Value Channel 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78-79 80 81 82 83 84 85 86 87-89 90 Function Plane mirror XY segment 1 Plane mirror XY segment 2 Plane mirror XY segment 3 Plane mirror XY segment 4 Plane tile 2x Plane tile 3x Plane tile 4x Plane tile 5x Plane cross tile 2x Plane cross tile 2x inverse Plane cross tile 3x Plane cross tile 3x inverse Plane cross tile 4x Plane cross tile 4x inverse Plane cross tile 5x Plane cross ti
DMX protocol DMX DMX Value Channel 100 101 102 103 104 105 106 107 108 109 110 111 112 113 Function kaleidoscope - mode and mosaic segment selection: Square -static mode Square -dynamic mode Right triangular - static mode Right triangular - dynamic mode Isosceles triangular - static mode Isosceles triangular - dynamic mode Triangular 1 - static mode Triangular 1 -dynamic mode Triangular 2 -static mode Triangular 2 - dynamic mode Centered mosaic (rough)-static mode Centered mosaic (rough)-dynamic mode Cente
DMX protocol DMX DMX Value Channel 22 23 24 25 26 27 28 29 30 31 32 33-39 40 41 42 43 44 45-49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64-67 68 69 70 Function Key Black inverse Key White Key White inverse White flash Black flash Alpha flash Invert flash BW Flash Black and white to black and white inverse Flash Gradient Wipe X Gradient Wipe Y Reserved Gaussian filter Mean filter Laplacian filter Emboss filter Sharpness filter Reserved RGB effects: RGB subtract All Pixels RGB add All Pixels RGB add non-bla
DMX protocol DMX DMX Value Channel Function Type of control P1-zoom, P2-X-speed, P3- Y-speed 97-149 150 Reserved Layer keystoning P1,P2,P3 P1-squeezing/stretching in X, P2/P3-compressing & expanding in X/Y 151-199 Reserved 200 Picture merging - R/G/B gamma adjustment in blended edges P1, P2,P3 P 1- red, P 2 - green, P 3- blue 130 131 132 133 134 135 136 137 138 139 140 141 142 143 201-255 Reserved Gobo effect 2 -Parameter 1 0-255 Effect control Gobo effect 2 -Parameter 2 0-255 Effect contro
DMX protocol DMX DMX Value Channel 252 253-255 144 0 1-255 0 1-20 21-40 21-60 61-80 81-100 101-120 121-140 141-160 161-180 181-200 201-220 221-255 145 0-255 146 0-255 147 0-255 148 0-255 149 Function Type of control Straming from remote sources step Reserved Gobo selection White step 255 Gobos (one by one) step If Live input (251 DMX) is selected on channel 143: White screen step Video composite input-PAL system step SVIDEO input- PAL system step Video composite input-NTSC system step SVIDEO input- NTSC
DMX protocol DMX DMX Value Channel 15 16 17 18-19 20 21 22 23 24 25 26 27 28-29 30-37 38-39 40 41 42 43 44 45 46 47 48-49 50-57 58-59 60 61 62 63 64 65 66 67 68-69 70-77 78-79 149 80 81 Function No function Scrub (Display) the selected In Frame Scrub (Display) the selected Out Frame Reserved Addition mode Video Stream 1 Play forward if dimmer (on layer 4) > 0, looping continuously Play forward if dimmer (on layer 4) > 0, hold on last frame Pause Play forward in continuous loop Play forward once and h
DMX protocol DMX DMX Value Channel 82 83 84 85 86 87 88-89 90-97 98-99 149 100 101 102 103 104 105 106 107 108-109 110-117 118-255 150 0 1-127 128 129-255 151 0-63 64-127 128 129-192 193-255 152 0-255 153 0 1 2 3 4 5 6 7 8 9 10 11 Function Type of control Pause Play forward in continuous loop Play forward once and hold on the last frame No function Scrub (Display) the selected In Frame Scrub (Display) the selected Out Frame Reserved Video Stream 2 the same functionality as for Video stream 1 Reserved
DMX protocol DMX DMX Value Channel 12 153 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 Function XY pos. circle clockwise XY pos. scroll up XY pos. scroll down XY pos. scroll left XY pos.scroll right Right-left diag. down scroll Right-left diag. up scroll Left-right diag. down scroll Left-right diag. up scroll X rotate Y rotate XY rotate XY inv. rotate X inv. y rotate Tile xy Tile xy XYZ rot. cube XYZ rot.
DMX protocol DMX DMX Value Channel 62 153 63 64 65 66 67 68 69 70 71 72 73 153 74 75 76 77 78-79 80 81 82 83 84 85 86 87-89 90 Function Plane cross tile 5x inverse Plane cross tiler 5x Plane cross tiler 5x inverse Plane bar Plane bar inverse Plane bar left-righ Plane bar top-bottom Reserved Reserved Gobo disc Gobo disc Flip X Gobo disc Flip Y Gobo disc Flip XY Gobo disc mirror X Gobo disc mirror Y Gobo disc mirror XY Reserved Plane mirror X top inverse Plane mirror X bottom inverse Plane mirror Y left inve
DMX protocol DMX DMX Value Function Channel 112 Centered kaleidoscope (fine)-static mode 113 Centered kaleidoscope (fine)-dynamic mode Type of control P1, P2, P3 P1, P2, P3 Stat. mode:P1-density, P2-content (coarse), P3-content (fine) Dyn.
DMX protocol DMX DMX Value Channel 41 42 43 44 45-49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64-67 68 69 70 Function Mean filter Laplacian filter Emboss filter Sharpness filter Reserved Type of control P1-amount P1-amount P1-amount P1-amount RGB effects: RGB subtract All Pixels RGB add All Pixels RGB add non-black Pixels RGB substract/add All Pixels Swap RGB to RBG Swap RGB to GRB Swap RGB to GBR Swap RGB to BRG Swap RGB to BGR RGB invert Invert and swap RGB to BRG Invert and swap RGB to GBR Colour to
DMX protocol DMX DMX Value Function Type of control Channel 160 Gobo effect 2 -Parameter 3 0-255 Effect control depends on effect 161 Gobo Position X coarse 0-127 Movement forward proportional 128 Centre (128-default) step 129-255 Movement backward proportional 162 Gobo position X fine 0-255 Position X fine proportional 163 Gobo position Y coarse 0-127 Movement down proportional 128 Centre (128-default) step 129-255 Movement up proportional 164 Gobo position Y fine 0-255 Position Y fine proportional 165 Gob
