Version 1.
DigitalSpot 3000 DT II Table of contents 1. Safety instructions ...................................................................................................................................................... 4 2. Unpacking ................................................................................................................................................................... 5 3. Introduction ...................................................................................................
DigitalSpot 3000 DT II 19. Playback speed ......................................................................................................................................................34 20. Graphic effects ........................................................................................................................................................35 20.1 Kaleidoscopic effect ....................................................................................................................
DigitalSpot 3000 DT II FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE POWERING OR INSTALLING YOUR DIGITALSPOT 3000 DT II ! Save it for future reference. This device has left our premises in absolutely perfect condition. In order to maintain this condition and to ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written in this manual.
DigitalSpot 3000 DT II When choosing the installation spot, please make sure that the device is not exposed to extreme heat, moisture or dust. Air vents and slots in the fixture´s head and base are provided for ventilation, to ensure reliable operation of the device and to protect it from overheating. The openings should never be covered with cloth or other materials, and never must be blocked. This fixture should not be placed in a built-in installation unless proper ventilation is provided.
DigitalSpot 3000 DT II 3. Introduction The DigitalSpot 3000 DT II features moving head with a video projection and automated lighting technologies including a DMX controllable digital media server installed in a fixture´s base. The built-in 32-bit Graphics Engine utilizes Linux and DirectX application programming interface to provide extensive image control of graphic objects.
DigitalSpot 3000 DT II Rear panel of the fixture base 1 - AT power 2 - Power cord 3 - Power switch 4 - Fuse 5 - Composite input-graphic engine 6 - S-video input- graphics engine 7 - DMX input/output (5-pin XLR) 8 - LAN (RJ-45) port 9 - DMX input/output (3-pin XLR) 10 - 2 x USB port 11 - S-video input-dataprojector 12 - Composite input-dataprojector 4.1 Placing fixture head covers The head cooling fans are fixed in head covers and their supply is realized by a pair of springy contacts.
DigitalSpot 3000 DT II 6. Connection to the mains Install a suitable plug on the power cord, note that the cores in the power cord are colored according to the following table. Core (Eu) Core (US) Pin Symbol Brown Black Live L Light blue White Neutral N Yellow/Green Green Earth The earth has to be connected! 6.
DigitalSpot 3000 DT II --->"Ceiling Projection"--->"On") Note that a special rear projection screen is required. When determining the position of the fixture and projection screen, you will need to account for the projected image size, which is directly proportional to the projection distance. There is a chart of throw distance ratio of 1.93-2.16 : 1 to assist you in determining the ideal location for your fixture. Min zoom is default setting. Max. zoom is possible after manual adjustment only.
DigitalSpot 3000 DT II characteristics. This will help you determine the exact mounting position so that it best suits your installation location 8.1 Changing the zoom 1. Turn the power off and if the projector lamp was on, wait 10 minutes until the projector has cooled. 2. Remove the top cover of the fixture head by loosening the four quarter-turn fasteners (1). 3. Unscrew 2 fastening screws (2) which securing the focus driving motor (3). Turn the motor up in order to allow an access to the zoom ring (4).
DigitalSpot 3000 DT II these qualifications, do not attempt the installation yourself, but instead use a professional structural rigger. Improper installation can result in bodily injury and or damage to property. The fixture must never be fixed swinging freely in the room. Use 2 appropriate clamps to rig the fixture on a truss. Make sure that the device is fixed properly! Ensure that the structure (truss) to which you are attaching the fixtures is secure.
DigitalSpot 3000 DT II 10. DMX 512 connection The fixture is equipped with both 3-pin and 5-pin XLR sockets for DMX input and output. Only use a shielded twistedpair cable designed for RS-485 and 3-pin/5-pin XLR- connectors in order to connect the controller with the fixture or one fixture with another.
DigitalSpot 3000 DT II 2- TD3- RX+ 4- Not connected 6- RX7- Not connected 8- Not connected Patch cables that connect fixtures to the hubs or LAN sockets are wired 1:1, that is, pins with the same numbers are connected together: 1-1 2-2 3-3 4-4 5-5 6-6 7-7 8-8 If only the fixture and the computer are to be interconnected, no hubs or other active components are needed. A cross-cable has to be used: 1-3 2-6 3-1 4-8 5-7 6-2 7-5 8-4 Ethernet operation.
DigitalSpot 3000 DT II 12. Folder organization The library structure is reflected on the hard drive where all files for the library are stored. The whole library is contained within a special folder called ‘Media’. Inside the Media folder is a collection of folders (000,001...240) each named with a 3-digit number. Each folder following this convention represents a library folder and the 3-digit number represents the name of the folder.
DigitalSpot 3000 DT II 13.
DigitalSpot 3000 DT II Menu Level 1 Menu Level 2 Display Adjusting Menu Level 3 Menu Level 4 Lamp Off via DMX On, Off Lamp On If DMX is Present On, Off Lamp Off if not DMX Display Permanent On Menu Level 5 On, Off Display Off After 5 min Permanent On Display Orientation Pan/Tilt Feedback Normal Orientation Rotated Orientation On, Off Pan/Tilt Mode Time Mode Speed Mode Active Blackout While: Projection Presetting During Movement Cor.
DigitalSpot 3000 DT II Menu Level 1 Menu Level 2 Menu Level 3 Menu Level 4 Menu Level 5 Menu Level 6 Pan 0-255 : Tilt 0-255 Program 10 Focus 0-255 Menu Level 7 Synchro Verbose Mode Default Settings Set Default Values Remove User Media Content Lamp On/Off On, Off Manual Control Manual DMX Control Pan 0-255 : Synchro to L3 Video Input Selection 0-255 Internal Input External Composite Input Stand-alone Setting Play Program External SVideo Input Test program In Loop Program 1 Norma
DigitalSpot 3000 DT II Menu Level 1 Menu Level 2 Menu Level 3 Record DMX Program DMX Program 10 in Loop DMX Program 1 Menu Level 4 Menu Level 5 : DMX Program 10 Preset Playback Deactivated : Fixture Off Timer DMX Program 10 in Loop Timer Deactivated Timer Activated Set Timer Hours Set Timer Minutes Preview Mode Reset Functions Reset Graphics Engine Reset Pan/Tilt System Reset Focus/Shutter System Reset All Systems Service Menu Power On Time Total Hours Resetable Hours Lamp On Time Total H
DigitalSpot 3000 DT II Menu Level 1 Menu Level 2 Menu Level 3 Menu Level 4 Menu Level 5 Menu Level 6 Menu Level 7 Menu Level 8 Media Open 000 Open LED Panel Board Air Filters Special Functions Time To Clean Up Filters Set clean Up Timer Regenerate Thumbnails Set Thumbnail size Regenerate Thumbnails FTP Server Set Account Allow Anonymous HTTP Access USB Data Synchronize 10..50..300 50..96...
DigitalSpot 3000 DT II Menu Level 1 Menu Level 2 Menu Level 3 Menu Level 4 Menu Level 5 Menu Level 6 Menu Level 7 Menu Level 8 Fixture Off 14. Operating modes Before operating the DigitalSpot 3000 DT II from a DMX 512 controller, you need to define the source of DMX data, which may be: DMX 512 - data is transmitted over standard DMX cables. Set a valid DMX start address, which is defined as the first channel from which the DigitalSpot 3000 DT II will respond to the controller.
DigitalSpot 3000 DT II Default IP Address -Preset IP address. Custom IP Address - The option enables edit all numbers of the IP address. To set the custom IP address: 1. Select „Custom IP Address” and press the [ENTER]. 2. Use RNS wheel to set the first number of the IP address 3. Press the [ENTER] to move on the second number of the IP address 4. Repeat steps 2 and 3 for the third and fourth number of the IP address. If you want to return back on the previously edited number, press [ESC].
DigitalSpot 3000 DT II Lamp Off if not DMX - This function allows you to switch off the lamp automatically after 2 minutes if a DMX signal is missing on the data link.
DigitalSpot 3000 DT II Verbose Mode --- Use this menu to hide messages displayed on the screen when you are changing some setting on the Power/Special functions channel (e.g. Rear projection on, Rear projection off.....) . Verbose Mode 0 --- Generated messages are hidden. Verbose Mode I --- Generated messages are visible on the projection screen.
DigitalSpot 3000 DT II Static - This mode is suitable for projections on the wall, ceiling or ground without any head movement. By means of items Pan, Tilt and Focus is possible to adjust moving head to the desired position. Running program is possible to pause by pressing the [ENTER] button. Edit Program --- Select this menu to edit or create a program. The DigitalSpot 3000 DT II has 10 freelyprogrammable programs, each up to 99 steps.
DigitalSpot 3000 DT II Note: If you select the program which contains previously recorded data, the data will be overwritten without warning. Preset playback --- The menu allows to select a program (or a DMX program), which will be played automatically in a loop after switching the fixture on. Fixture Off Timer --- The menu offers to control the time during which the fixture is on and, for example, plays the recorded program. The adjusted time period is counted from starting the fixture.
DigitalSpot 3000 DT II since the respective counter was last reset. In order to reset desired counter to 0, press [ENTER] twice. Measuring points of temperatures: Pan /Tilt Board. [°C] ...............temperature on the PCB in the fixture base Led Panel Board [°C]................temperature in the LED module Air Filters --- Regular cleaning of the air filters is very important for the DigitalSpot 3000 DT II life and performance.
DigitalSpot 3000 DT II Top level folder Media 000 001 002 : 240 Programs Update Log : To create the folders structure mentioned above, use the option "Init Flash Disc". After creating folders structure on the USB stick you may load/download files into folders/subfolders .Maximum number of media files in one Media subfolder is 240. Subfolders 000-020 are reserved for default images/videos and cannot be changed (you cannot copy media files into these subfolders).
DigitalSpot 3000 DT II after updating, run update of the hardware functions. Update HW processors Software - starts update of hardware functions like pan, tilt, focus...etc. Update Media Content - starts update of the factory media folders 00-20 (pictures, videos) Calibrate Values --- This menu serves for a fine calibration of effects. Analog Shutter - allows ine calibration of a mechanical shutter (projector lamp has to be turned on). Tilt Calibration -allows fine calibration of a tilt.
DigitalSpot 3000 DT II use channel KeyStone X-ratio for correction use channel KeyStone Y-ratio for correction If the channel Global effect 1 - Parameter 3 is set to the range of 171-180, the aspect ratio of an actual image is displayed in the image. The feature is activated when the Picture Merging is active only. 16.
DigitalSpot 3000 DT II 2. Gobo position in X and Y direction. The channels Gobo position X coarse and Gobo position X fine allow 8-bit/16-bit positioning in X-direction. The channels Gobo position Y coarse and Gobo position Y fine allow 8-bit/16-bit positioning in Y-direction. 3. Layer skewing along X and Y axis. On the channel Gobo effect 1 selection adjust a DMX value=150 and using the control parameters 1 an 2 you can skew the image in either X or Y axis.
DigitalSpot 3000 DT II The channel Gobo effect 1 – Parameter 2 skews the image in Y-axis. 4. Layer Squeezing/Stretching along X and Y axis. On the channel Gobo effect 1 selection adjust a DMX value=150 and using the Control Parameters 3 you can squeeze the image in X axis. The channel Gobo effect 1 – Parameter 3 squeezes/stretches the image edges in Y-axis. On the channel Gobo effect 2 selection adjust a DMX value=150 and using the control parameters 1 you can squeeze the image in Y axis. Note.
DigitalSpot 3000 DT II 5. Image X-ratio and Y-ratio. On the channel Gobo effect 2 selection adjust a DMX value=150 and the second and third parameter control image X-ratio and Y-ratio. Note. To allows this effect, the channel Gobo effect 1 selection has to be set at DMX=150. The channel Gobo effect 2 – Parameter 2 compresses or expands the image in X- axis The channel Gobo effect 2 – Parameter 3 compresses or expands the image in Y- axis.
DigitalSpot 3000 DT II 17. In Frame and Out Frame parameters You can select any segment of a video file for playback by assigning parameters for In Frame (start point) and an Out Frame (end point) as pictured below. The In Frame parameter corresponds to a 16-bit DMX value equal to a starting point for the playback segment of the selected video file. The Out Frame parameter corresponds to a 16-bit DMX value equal to an end point for the playback segment of the selected video file. 1.
DigitalSpot 3000 DT II The playback options: DMX value Playback options Meaning 0. Play forward continuously if dimmer >0 Plays the video segment from In Frame point to Out Frame point, continuous looping. The dimmer value has to be greater than 0. 1 Play forward once if dimmer >0 Plays the video segment from In Frame point to Out Frame point and holds on the last frame. The dimmer value has to be greater than 0.
DigitalSpot 3000 DT II 20. Graphic effects There are two gobo effect channels on each gobo layer (Gobo effect 1 selection, Gobo effect 2 selection), which offer amount of effects that can be applied to the current running picture/video. Each effect channels have three control channels - Parameter 1, Parameter 2, Parameter 3 – which allow to change the behaviour of selected effect (e.g. speed, amount...) 20.
DigitalSpot 3000 DT II DMX value Static mode Dynamic mode Mosaic effect Examples Source picture Centered Kaleidoscope (rough) 110 111 Note: As the effect does not cover all projection are, the image from the lower layer can be displayed at the sides of the effect. E.g. Centered Kaleidoscope effect has been selected on the layer 4 and the picture on the layer 3 is visible at the sides of the effect.
DigitalSpot 3000 DT II If the effect “Centered Kaleidoscope (fine) ” is selected, meaning of the Parameter 1 is the following: DMX value Function 0 - 255 Shape and a number of mirroring planes Gobo effect 1- Parameter 2: Size and pulsation of the segments content DMX value Function 0 - 128 Size of segments content from small (0 DMX) to large (128 DMX) 129 - 255 Speed of segment pulsation from slow (129 DMX) to fast (255 DMX) Gobo effect 1- Parameter 3: Movement of the segments content DMX value Function 0
DigitalSpot 3000 DT II Associated control parameters: Control parameter Parameter 1 Parameter 2 Parameter 3 Controlled item Red colour element Green colour element Blue colour element DMX value 0-255 0-255 0-255 Function no adjustment minimum saturation no adjustment minimum saturation no adjustment minimum saturation RGB add All Pixels (DMX value=51) – the effect increases colour values across all pixels.
DigitalSpot 3000 DT II Swap RGB to GBR (DMX value=56) – the effect swaps red to green, green to blue and blue to red colour in all pixels.
DigitalSpot 3000 DT II Associated control parameters: Control parameter Parameter 1 Controlled item Red colour element DMX value 0-255 Parameter 2 Green colour element 0-255 Parameter 3 Blue colour element 0-255 Function no adjustment (0 ) full inverted blue (255) no adjustment (0 ) full inverted red (255) no adjustment (0 ) full inverted green (255) Invert and swap RGB to GBR (DMX value=61) – the effect swaps red, green and blue colour to inverted GBR in all pixels.
DigitalSpot 3000 DT II RGB scale (DMX value=68) – the effect changes the output intensity of red, green and blue colour in all pixels. Associated control parameters: Control parameter Controlled item DMX value Function Changes the inclination of conversion line for red colour from max. output intensity (0 ) no adjustment (255) Parameter 1 Red colour 0-255 Changes the inclination of conversion line for green colour from max.
DigitalSpot 3000 DT II 20.4 Iris effect on layer The effect allows to simplify transition effects between layers and it can be activated on each gobo layer. On the effect can be applied layer´s X/Y zoom, X/Y position and rotation parameters. Another possible application of the iris effect is to use it as the mask function to mask unwanted parts of the image. On the iris effect on the layer can be also applied global effects as the iris, picture merging etc.
DigitalSpot 3000 DT II Gobo Effect 1-Parameter 3: Texture modes applied on the iris surface Parameter 3 DMX value (Mode) Zoom X Zoom X + Position X 0-9 (Mode 1) 10-19 (Mode 2) 20-29 (Mode 3) 30-39 (Mode 4) The following modes (5-8) include black mask 40-49 Dimmer on the layer 3= 255 DMX Dimmer on the layer 3= 255 DMX (Mode 5) Dimmer on the layer 3= 1 DMX Dimmer on the layer 3= 1 DMX 43
DigitalSpot 3000 DT II Parameter 3 DMX value (Mode) Zoom X Position X 50-59 Dimmer on the layer 3= 255 DMX Dimmer on the layer 3= 255 DMX Dimmer on the layer 3= 1 DMX Dimmer on the layer 3= 1 DMX Dimmer on the layer 3= 255 DMX Dimmer on the layer 3= 255 DMX Dimmer on the layer 3= 1 DMX Dimmer on the layer 3= 1 DMX Dimmer on the layer 3= 255 DMX Dimmer on the layer 3= 255 DMX Dimmer on the layer 3= 1 DMX Dimmer on the layer 3= 1 DMX (Mode 6) 60-69 (Mode 7) 70-79 (Mode 8) The iris effect can
DigitalSpot 3000 DT II 20.5 Auto iris effect on layer The effect behaves similar as Iris effect on layer, but it is auto- triggered by gobo changes. The iris effect on layer can be activated on each gobo layer if you set the Gobo Effect 1 Selection channel to a DMX value of 92. The Parameter 1 of this effect changes the speed of the iris movement. The Parameter 2 changes the iris mask type.
DigitalSpot 3000 DT II 20.7 Another graphic effects on layers 1. Swirl effect Activation channel Activation DMX value Control: Parameter 1 Parameter 2 Parameter 3 Gobo Effect 2 Selection (on each layer) 70 Radius: 0-255DMX - min.
DigitalSpot 3000 DT II 3. Cross-stitching effect Activation channel Activation DMX value Control: Parameter 1 Parameter 2 Parameter 3 Gobo Effect 2 Selection (on each layer) 72 Pattern density: 0-255 DMX - max. min. Colour of stitch: 0-127 DMX - coloured 128-255 DMX - black Effect boundary position in X-axis: 0-255 DMX – movement of effect boundary from left to right Original P1=81DMX, P2=0DMX, P3=85DMX Default value 0 0 0 P1=81DMX, P2=128DMX, P3=85DMX Example 4.
DigitalSpot 3000 DT II 21. Media content management As you seen earlier in chapter "12. Folder organization", the DigitalSpot 3000 DT II uses the root folder named "Media". This folder contains subfolders (000,001...240) and inside each subfolder is the collection of media that the subfolder holds. The files in subfolders are sorted in an alphabetic or numerical order and assigned to DMX. The first part of the file name should be a 3-digit number followed by an underscore and a name e.g.: 001_sun..........
DigitalSpot 3000 DT II After network configuration, type the IP address of the DigitalSpot 3000 DT II in address line in your Windows explorer window. Use this format ftp:// 2.X.X.X / (e.g. ftp://2.236.2.88/- see picture below). If all settings are proper, you will see "Media" and "Update" folders in the Windows explorer window and now you can work with them as local folders and files. See also "Special functions"--> "FTP Server".
DigitalSpot 3000 DT II 2. FTP client in Mozilla Firefox If you use Mozilla Firefox as your web browser, you can install FTP client into the browser. To install FTP client for Mozilla Firefox on your computer. 1. Run Mozilla Firefox. 2.Select option “ Tools” from the Menu bar, select “Add-ons” item. 3.Select option “Get Add-ons” from the standard toolbar, type fireftp into the top left field and press Enter key. 4.Click on the Add to Firefox.. button and follow the installation instructions. 5.
DigitalSpot 3000 DT II After installing FTP client, run Mozilla Firefox and type the IP address of desired fixture in ftp format e. g. ftp://2.97.181.89 and a Fire FTP window will appear. If you do not want to keep in mind IP addresses of all connected fixtures, you can use the Remote configuration program (by typing the IP address of one fixture to the web browser in http format e. g. http://2.97.181.89) and go to the Contents Synchronization window where a list of available fixtures is offered.
DigitalSpot 3000 DT II 21.2 Moving files between networked fixtures The option "Contents Synchronization" in a "Remote control program" running on your PC offers easy control of file transfer between networked fixtures via WWW browser. (For detail description of the Remote configuration program see chapter "Remote control of the fixture via WWW browser" below). A window of Contents Synchronization: There is a list of available fixtures under Device Available for Update.
DigitalSpot 3000 DT II Personality - the window allows you to change the fixture settings like a pan/tilt reverse, feedback, speed, lamp status, DMX protocol selection etc. Status Messages -the window under this option displays error and status messages. Special Functions - the window offers several items: "Thumbnails size" - changing the size of the thumbnails. The change takes effect in the item "Content". If you change the thumbnail size, use the button "Update" below the size box.
DigitalSpot 3000 DT II "Log File" - enables to generate log file for service purposes. "System Reboot"- starts reboot of the fixture "Regenerate Video Headers"- allows to regenerate headers of video media files. Content - by entering this window a complete overview of all gobo folders is offered, from which the folder to be view can be selected.Click a desired folder to display its content. Click a desired picture to zoom it in.
DigitalSpot 3000 DT II There is a list of available fixtures under Device Available for Update. If you connect another fixture to a network, use option "Rescan Devices" to refresh the list of fixtures. A list of available folders with their check boxes is placed under Synchronization Folders. Option "Synchronization Mode" gives you possibility to select the way how the files will be moved to target folder: "Mirror"- a content of the target folder will be fully overwritten by a content of the source folder.
DigitalSpot 3000 DT II http://2.x.x.x:port number (for example http://2.1.1.3:1234) and click the "Update" button on the right side of the line to save the streaming source address. This source is assigned to the DMX value of 1 on channel Gobo selection. Up to 20 streaming sources is possible to define in this way. All defined streaming sources are assigned to DMX values of the Gobo selection channel and can be used on each gobo layer.
DigitalSpot 3000 DT II Global effect 1- Parameter 1 The DMX value from the range of 1- 235 allows selection of desired image field configuration according to the tables on the following pages.
DigitalSpot 3000 DT II DMX value Image field Configuration WxH Total number of fixtures DMX value Image field Configuration WxH Total number of fixtures 37 1x7 7 92 11 x 2 22 38 7x2 14 93 2 x 11 22 39 2x7 14 94 11 x 3 33 40 7x3 21 95 3 x 11 33 41 3x7 21 96 11 x 4 44 42 7x4 28 97 4 x 11 44 43 4x7 28 98 11 x 5 55 44 7x5 35 99 5 x 11 55 45 5x7 35 100 12 x 1 12 46 7x6 42 101 1 x 12 12 47 6x7 42 102 12 x 2 24 48 7 x7 49 103 2 x 12 24 4
DigitalSpot 3000 DT II Horizontally mirrored configuration DMX value Image field configuration of base matrix WxH Total number of fixtures in base matrix DMX value Image field configuration of base matrix WxH Total number of fixtures in base matrix 128 2x1 2 146 10 x 2 20 129 4x1 4 147 4x5 20 130 2x2 4 148 10 x 3 30 131 4x2 8 149 6x5 30 132 6x1 6 150 10 x 4 40 133 2x3 6 151 8x5 40 134 6x2 12 152 10 x 5 50 135 4x3 12 153 12 x 1 12 136 6x3 18 154 2x6
DigitalSpot 3000 DT II Vertically mirrored configuration DMX value Image field configuration of base matrix WxH Total number of fixtures in base matrix DMX value Image field configuration of base matrix WxH Total number of fixtures in base matrix 164 1x2 2 182 5x4 20 165 2x2 4 183 2 x 10 20 166 1x4 4 184 5x6 30 167 2x4 8 185 3 x 10 30 168 3x2 6 186 5x8 40 169 1x6 6 187 4 x 10 40 170 3x4 12 188 5 x 10 50 171 2x6 12 189 6x2 12 172 3x6 18 190 1 x 12 12
DigitalSpot 3000 DT II Vertically and horizontally mirrored configuration DMX value Image field configuration of base matrix WxH Total number of fixtures in base matrix DMX value Image field configuration of base matrix WxH Total number of fixtures in base matrix 200 2x2 4 218 10 x 4 40 201 4x2 8 219 4 x 10 40 202 2x4 8 220 10 x 6 60 203 4x4 16 221 6 x 10 60 204 6x2 12 222 10 x 8 80 205 2x6 12 223 8 x 10 80 206 6x4 24 224 10 x 10 100 207 4x6 24 225 12 x 2
DigitalSpot 3000 DT II The mirrored image configurations bring 2 advantages: 1. Resolution of the source image and merged images on the wall is the same in comparison with non-mirrored configuration (if you use suitable mirrored configuration – see example 3 below). 2. By using the picture merging with mirrored configuration you can cover any size of projection area. The base matrix of fixtures can be repeated. The total number of used projectors is unlimited.
DigitalSpot 3000 DT II Global effect 1- Parameter 2 The DMX values from the range of 0-255 are used to step segment by segment throw the image grid. The DMX value of 0 corresponds to the upper left segment of the image grid. The stepping runs from the left to the right and down from top (see example for field 8x3 segments bellow). Global effect 1- Parameter 3 This channel enables to transform displaying of the segment edges-sharp or blended edges.
DigitalSpot 3000 DT II Global effect 2 A DMX value of 20 enables fine adjusting of the red, green and blue gamma curve at overlapping edges to achieve consistent colour( brightness) of these parts of image. Note. After selecting desired image segment for the gamma correction (by means of the Global effect 1 Parameter 2), set the channel Global effect 1 - Parameter 3 to 0 in order to display blended edges of the picture segment.
DigitalSpot 3000 DT II 24. Pre-cut content mode for Picture Merging The mode is useful when you want to cover large projection area with full resolution for each projector or you don't want to be restricted with limits of matrix configuration. The basic idea is that before projection you have to prepare the pre-cut content (e.g. picture) and upload the single parts of the splitted source picture into individual fixtures.
DigitalSpot 3000 DT II Size of segments in X-axis: LpartX = LtotalX/[x-(b/100)*(x-1)] LpartX =1024/ [3-(10/100)*(3-1)] the size of overlapping edges was selected 10% (b=10) LpartX = 366 pixels Since the size of the segments in Y-axis is the same as at the source picture, each of the 3 fixtures will project picture with resolution of 366x768 pixels. ___________________________________________________________________________________________ Note.
DigitalSpot 3000 DT II 25. Effect video synchronization The synchronization option can be set separately for each gobo layer (channels Synchronization to ID). The fixture synchronization acts with the fixture ID which is defined as the last number of fixture´s IP address. This fixture ID is shown on the fixture´s display. The fixtures are synchronized to the one fixture - named a master fixture.
DigitalSpot 3000 DT II 26. Projection onto angular, cylindric or spheric surfaces If a projection on curved surface is required a correction of the shape distortions is necessary. The DigitalSpot 3000 DT II supports projection onto angular screens, cylinders and spheres. 26.1 Curved surface support channels Global effect 2 This channel enables you to select desired shape of the surface: To simplify a correction process, there is a gobo with a net pattern (DMX value = 2) in a factory folder No.
DigitalSpot 3000 DT II Global effect 2- parameter 2 This parameter enables to adjust the horizontal length of the edge. A DMX Value of 128 = no adjustment, values below 128 move the edge to the left, values above 128 move the edge to the right. Global effect 2- parameter 3 This parameter enables to adjust the vertical length of the edge. A DMX Value of 128 = no adjustment, values below 128 move the edge downwards, values above 128 move the edge upwards.
DigitalSpot 3000 DT II Note: If a projection of rectangle (square) on a circle (sphere) is selected on the channel Global Effect 2 (DMX value of 10 or 11), the meaning of the Keystone parameters in a DMX chart will be changed as follows: Channel Type of control DMX value Function 0 -127 128 129-255 Image moving in an X-direction Moving the image from left to center Center Moving the image from center to right proportional step proportional 0 -127 128 129-255 Image moving in a Y-direction Moving the i
DigitalSpot 3000 DT II 27. Video processing on gobo layers from a streaming video server A streaming video is a video that is continuously sent by one device (e.g. PC) and received by another device (DigitalSpot 3000 DT II) over an ethernet network. 1. TightVNC client The TightVNC is a free remote control software package available at http://www.tightvnc.com/download.php .
DigitalSpot 3000 DT II Hire is an example for Windows XP: 5. Run a Remote control by means of WWW browser at your PC, select option “Remote content” and write IP address of TightVNC server to the Source Address line in the following format : vnc:// xxx.xxx.xxx (e.g. vnc://2.1.1.12). 2. Streaming video server The Streaming video software stated on the pictures below is available at http://www.videolan.org/vlc/.
DigitalSpot 3000 DT II - Click on the "Properties" button and the following window will open. - Click on the item "Internet Protocol (TCP/IP)" and the Internet Protocol Properties window will open. Set IP address to something like 2.X.X.X with an IP mask of 255.0.0.
DigitalSpot 3000 DT II 3. Install a VLC media player- click on a VLC media player self-extracting package located on the hard disk and follow the on-screen instructions. After installing it, run this VLC media player. In a horizontal menu "File" click on "Open" and the following window will open. Type the name of video file in the "Open" field, check the "Stream/Save" option and click the "Settings" button.
DigitalSpot 3000 DT II Check the "HTTP" option in a Outputs column, type an IP address of the PC in the "Address" field and a figure port in the "port" field. Note: If you want to run more videos on this PC, you have to run the VLC media player for each video and every media player has to have a different figure of the port but the IP address will be the same. Select the MPGTS or MPEGPS option in the "Encapsulation method" row. Check the "Video codec" option and select mp2v.
DigitalSpot 3000 DT II screen:// screen-fps=10 :screen-caching=100 Space The Stream output window has the same setting like for video streaming except the field "Bitrate (kb/s)" which should be set at the value of 8192. Important: The Playback speed channel at corresponding gobo layer should be set at a DMX value of 150-200.
DigitalSpot 3000 DT II Control PC (light console) Type the IP address of the DigitalSpot 3000 DT II which is to project data from a remote streaming video source in your WWW browser to run the Remote Control program. Select the option "Remote Content" and the following window will open: Type in the "source Address" field the IP address and the port number of the streaming source (in our case it is a PC) in this format: http://2.x.x.x:port number e.g. http://2.1.1.
DigitalSpot 3000 DT II Fixture linkage: 28. RDM This fixture is ready for RDM operation.RDM (Remote Device Management) is a bi-directional communications protocol for use in DMX512 control systems, it is the new open standard for DMX512 device configuration and status monitoring. The RDM protocol allows data packets to be inserted into a DMX512 data stream without adversely affecting existing non-RDM equipment.
DigitalSpot 3000 DT II The CITP protocol allows to report folders for live input and streaming.
DigitalSpot 3000 DT II 29. Technical specifications Electrical specifications: Auto-switching power supply Input voltage range: 100-120V/ 200-240V AC, 50/ 60 Hz Max. Pover Consumption @ 230V: 400W/430VA (I=1.9A, power factor=0.93) Projector Specifications: Model MP670 Light output: 3200 ANSI lumens Lamp: 230W Rated lamp life: 3000/4000 hours (normal/eco mode) Aspect ratio: 4:3 Resolution: XGA (1,024x768) Image size 23“ to 300“ Throw ratio: 1.93 - 2.
DigitalSpot 3000 DT II Video processing on all gobo layers from remote streaming video server Control 5“ TFT LCD display & Robe navigation system Web access for total control of fixture (user library management) Media Content Synchronization in web interface Protocol USITT DMX 512 Support of CITP/MSEX protocol 136 control channels max.
DigitalSpot 3000 DT II Dimensions (mm) Weight 28 kg Accessories 2x Omega holder (No.99010420) 1x USB 2.0 flash drive with a System recovery utility. 2x Adapter BNC/CINCH (No. 13051401) Optional accessories DVI/VGA capture card set (No. 99013073) – includes capture card DVI/VGA Unigraph and mounting accessories SDI/ASI capture card set (No. 99013074) – includes capture card SDI/ASI DTA-145-SDP and mounting accessories DVI-VGA DS 3500/3000 II/7100 capture card set (P.N.
DigitalSpot 3000 DT II 30. Error and information messages The warning icon (triangle) on the bottom-right side of the fixture´s screen indicates some error or information message which appears on the screen by pressing the [ESC] button. Pan Error The message will appear after the reset of the fixture if the yoke´s magnetic-indexing circuit malfunctions (sensor failed or magnet is missing) or the stepping motor is defective or its driving IC3 on the PCB in the fixture base.
DigitalSpot 3000 DT II Dataprojector Abnormal Temperature System message from dataprojector. Dataprojector Lamp Failure System message from dataprojector. DMX Address Is Over Limit The DMX start address is set to value that does not make possible receiving all DMX channels. USB Communication Failure The message signalizes problem with communication between PC motherboard and the motor driver board. Network Communication Failure The message signalizes problem with Ethernet interface on PC motherboard.
DigitalSpot 3000 DT II 31. Maintenance 31.1 Replacing the lamp Turn the power off and disconnect the fixture from the mains. If the lamp is hot, avoid burns by waiting for approximately 45 minutes until the lamp has cooled. 1. Remove the bottom cover/cover with air vents/ (1) of the fixture head by loosening the four quarter-turn fasteners (2). 4 2.Loosen the two captive screws (3) on the lamp compartment cover. Remove the lamp compartment cover (4). 3 3 3.
DigitalSpot 3000 DT II 7 5.Insert the new lamp (7) into the lamp compartment and make sure it fits in the projector. Ensure the connectors are aligned. If you experience resistance, lift the lamp and start again. 6.Tighten the screws (5) that secure the lamp. Ensure the handle is fully laid flat and locked in place. Loose screw may cause a bad connection, which could result in malfunction. Do not over tighten the screws. 5 7.Replace the lamp cover on the projector and tighten the captive screws (3).
DigitalSpot 3000 DT II 31.2 Replacing the projector If you need to remove the data projector, turn the power off and disconnect the DigitalSpot 3000 DT II from the mains. If the projector lamp is on, wait 20 minutes until the projector has cooled. 1. Remove both covers (1) of the fixture head (2) by loosening the four quarter-turn fasteners (3) on each cover. 2. Remove the rear cover (4) by loosening the four screws (5)on the plastic cover and the four screws (6) on the rear cover chassiss.
DigitalSpot 3000 DT II 31.3 Replacing the air filters Important! Check the air filters periodically and clean before they become clogged! Clean the air filters with a vacuum cleaner or you can wash them and put back dry. Replacing air filters in the fixture head. 1) Disconnect the fixture from power. 2) Raise up a filter cover (1) (fixed by two magnets) on the head cover 3) Pull the air filter (2) out. 4) Clean or replace the air filter. 5) Snap the filter cover back to the head cover.
DigitalSpot 3000 DT II 31.4 Replacing the fuse Only replace the fuse by a fuse of same type and rating. Before replacing the fuse, turn the power off and unplug the mains lead. Procedure: 1) Unscrew the fuse holder on the rear panel of the base with a fitting screwdriver from the housing (anti - clockwise). 2) Remove the old fuse from the fuse holder. 3) Install the new fuse in the fuse holder. 4) Replace the fuse holder in the housing and fix it. 31.
DigitalSpot 3000 DT II 31.6 Installing the DVI/VGA capture card To install the DVI/VGA capture card: 1. Disconnect the fixture from power. 2. Remove both top covers of the fixture base by unscrewing 14 fastening screws. 3. Remove the shield cover (1) by loosening three crews (2). 4. Disconnect data cables from the video capture card, take the card out of PCI slot and remove the S-video/Composite connectors holder (3) by unscrewing the two screws M3x10 (4).
DigitalSpot 3000 DT II 31.7 Installing the SDI/ASI capture card To install the SDI/ASI capture card: 1. Disconnect the fixture from power. 2. Remove both top covers of the fixture base by unscrewing 14 fastening screws. 3. Remove the shield cover (1) by loosening the 3 screws (2). 4. Disconnect data cables from the video capture card, take card out of the PCI slot and remove the S-video/Composite connectors holder (3) by unscrewing the two screws M3x10 (4).
DigitalSpot 3000 DT II 31.8 Cleaning Turn the power off and disconnect the fixture from the mains. before starting cleaning procedure. It is absolutely essential that the fixture is kept clean and that dust, dirt and smoke-fluid residues must not build up on or within the fixture. Otherwise, the fixture‘s light-output will be significantly reduced. Regular cleaning will not only ensure the maximum light-output, but will also allow the fixture to function reliably throughout its life.
Appendix - DMX protocol DigitalSpot 3000 DT II - DMX protocol v. 1.2; April, 2012 DMX DMX Value Channel 1 0-255 2 0-255 3 0-255 4 0-255 5 0 1-255 1-255 6 0-9 10-31 32-63 64-95 96-127 128-159 160-191 192-223 224-255 7 0 1-127 128-129 130-255 8 0-39 Function Pan Pan movement by 530° Pan Fine Fine control of pan movement Tilt Tilt movement by 280° Tilt Fine Fine control of tilt movement Pan/Tilt speed,Pan/Tilt time Max.speed (tracking mode) P./T. speed-set Speed Mode in menu: Pan/Tilt Mode Speed from max.
Appendix - DMX protocol DMX DMX Value Channel 115-119 Artnet In 120-129 Reserved 8 Type of control step To activate following function,hold DMX value 3 seconds 130-139 140-149 150-179 180-189 190-199 200-209 210-215 216-229 230-239 240-249 250-255 9 0-63 64-127 128-191 192-255 10 0-255 11 0-255 12 0-255 13 0-255 14 0-255 15 0-255 16 0-31 32-63 64-95 96-127 128-143 144-159 160-191 192-223 224-255 17 0-255 18 0-255 19 0-255 20 Function Lamp On Pan/Tilt reset Reserved Focus reset Reserved Total reset Grap
Appendix - DMX protocol DMX DMX Value Channel 0-255 21 0-255 22 0-255 23 0-255 24 0-255 25 0-255 26 0-127 128 129-255 27 0-127 128 129-255 28 0-255 29 0-255 30 0-255 31 0 1 2 3 4 5 6 7 8 9 10 11 12 13 : 255 32 0 1 2 3 4 Function Move top right corner X value to center (0-default) KeyStone Top Right Y Move top right corner Y value to center (0-default) KeyStoneBottom Right X Move bottom right corner X value to center (0-default) KeyStone Bottom Right Y Move bottom right corner Y value to center (0-default)
Appendix - DMX protocol DMX DMX Value Channel 5 6 7 8 9 32 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 27 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 Function Circular ,inside-->out,sharp edge Circular ,inside-->out,fuzzy edge 1 Circular ,inside-->out,fuzzy edge 2 Circular ,inside-->out,fuzzy edge 3 Circular ,inside-->out,fuzzy edge 4 (maximum) Horizontal ellipse ,outside-->in,sharp edge Horizontal ellipse ,outside-->in,fuzzy edge 1 Horizontal ellipse ,outside-->
Appendix - DMX protocol DMX DMX Value Channel 55 56 57 58 59 32 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 Function Radial wipe ,bottom-->left,sharp edge Radial wipe ,bottom-->left,fuzzy edge 1 Radial wipe ,bottom-->left,fuzzy edge 2 Radial wipe ,bottom-->left,fuzzy edge 3 Radial wipe ,bottom-->left,fuzzy edge 4 (maximum) Radial wipe ,top-->left,sharp edge Radial wipe ,top-->left,fuzzy edge 1 Radial wipe ,top--
Appendix - DMX protocol DMX DMX Value Channel 105 106 107 108 109 32 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 Function Vertical two-way band wipe,top right-->bottom left Horizontal bands 4x,top-->bottom Horizontal bands 4x,bottom-->top Vertical bands 4x,left -->right Vertical bands 4x,right -->left Horizontal bands 8x,top-->bottom Horizontal bands 8x,bottom-->top Vertic
Appendix - DMX protocol DMX DMX Value Channel 155 156 157 32 158 159 160 161-169 170 171 172 173 174 175 176 177 178 179 180-255 33 0 1-254 255 34 0-255 35 0 - 30 31 - 80 81 - 110 111 - 140 141 - 149 150 - 154 155 - 159 160 - 164 165 - 189 190-194 195-199 200 - 204 205-239 240-244 245-249 250-255 36 0-255 37 0-255 38 0-255 39 0-255 Function Grid wipe 16x16,top right-->bottom left,inverse Grid wipe 32x32,bottom right-->top left Grid wipe 32x32,bottom right-->top left,inverse Grid wipe 32x32,top right-->bott
Appendix - DMX protocol DMX DMX Value Channel 40 0-255 41 0-255 42 0-255 43 0-255 44 0-255 45 0 Function Banner top positioning Positioning from top to bottom (0-default) Banner top rotation Rotation +/- 45° (128-default) Banner bottom positioning Positioning from bottom to top (0-default) Banner bottom rotation Rotation +/- 45° (128-default) All Banners rotation Rotation +/- 45° (128-default) Global Effect 1 No effect Type of control proportional proportional proportional proportional proportional Pict
Appendix - DMX protocol DMX DMX Value Channel 2 3 4 5 6 7 8 9 10 11 12 13-19 20 21-255 50 0-255 51 0-255 52 0-255 53 0-255 54 0-20 21-240 241-250 251 252 253-255 55 0 1-255 55 0 1-20 21-40 21-60 61-80 81-100 101-120 121-140 141-160 161-180 181-200 201-220 221-255 Function Vertical outside corner mapping Horizontal inside corner mapping Horizontal outside corner mapping Vertical convex cylinder mapping Vertical concave cylinder mapping Horizontal convex cylinder mapping Horizontal concave cylinder mappi
Appendix - DMX protocol DMX DMX Value Function Type of control Channel 56 In Frame High 0-255 Defines the beginning of a media file segment as a proportional percentage of the movie length (0-default) In Frame Low 57 proportional 0-255 Defines the beginning of a media file segment as a percentage of the movie length (0-default) Out Frame High 58 0-255 Defines the end of a media file segment as a percentage of proportional the movie length (255-default) Out Frame Low 59 proportional 0-255 Defines the beginni
Appendix - DMX protocol DMX DMX Value Channel 60 40 41 42 43 44 45 46 47 48-49 50-57 58-59 60 61 62 63 64 65 66 67 68-69 70-77 78-79 60 80 81 82 83 84 85 86 87 88-89 90-97 98-99 100 101 102 103 104 105 106 107 Function Play forward if dimmer (on layer 1) > 0, looping continuously Play forward if dimmer (on layer 1) > 0, hold on last frame Pause Play forward in continuous loop Play forward once and hold on the last frame No function Scrub (Display) the selected In Frame Scrub (Display) the selected Out
Appendix - DMX protocol DMX DMX Value Function Channel 108-109 Reserved Video stream 2: 110-117 The same functionality as for Video stream 1 118-255 Reserved 61 Playback Speed 0 Normal Speed 1-127 Slow speeds from slowest ---> normal 128 Normal Speed 129-255 Faster than Normal ---> Fastest 62 Gobo rotation and indexing 0-63 Clockwise rotation from fast to slow 64-127 Indexing 128 No rotation-centre (128-default) 129-192 Indexing 193-255 Anticlockwise rotation from slow to fast 63 Gobo fine indexing (rotatio
Appendix - DMX protocol DMX DMX Value Channel 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 64 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78-79 80 81 82 Function Reserved Kaleidoscope Squeeze in Squeeze out Bend X Bend Y Tile frame Frame Plane Flip X Plane Flip Y Plane Flip XY Plane mirror X top Plane mirror X bottom Plane mirror Y left Plane mirror Y right Plane mirror XY segment 1 Plane mirror XY segment 2 Plane mirror XY segment 3 Plane mirror XY segment
Appendix - DMX protocol DMX DMX Value Channel 83 84 85 86 87-89 90 Function Plane mirror Y right inverse Plane mirror XY inverse Plane mirror X-inverse,Y Plane mirror X,Y-inverse Reserved Circular effect (Fish eye) Type of control none none none none P1, P2, P3 P1-character, P2-X ratio, P3-Y ratio 91 Iris on layer P1, P2, P3 P1-size, P2-iris type, P3-texture mode 92 Auto Iris effect on layer P1, P2, P3 P1-speed, P2-mask type, P3-opening/closing command 93-94 95 Reserved Zoom In/Move XY P1, P2,
Appendix - DMX protocol DMX DMX Value Channel 5 6 7 8 9 10 11 12 13 14 15 16 68 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33-39 40 41 42 43 44 45-49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 Function Black Mask Black Mask inverse Contrast Brightness RGB to GBR RGB to BRG RGB to RBG Black and white to black and white inverse timed Colour to black and white timed Colour to inverse timed Cycle Cycle inverse Reserved Reserved Colour Key Colour Key inverse Key Black Key Black inverse Key White Key White i
Appendix - DMX protocol DMX DMX Value Function Channel 64-67 Reserved 68 RGB scale P1-red, P2-green, P3-blue 69 Brightness scale P1, P2 - inclination of conversion line 70 Swirl effect Type of control P1, P2, P3 P1, P2 P1, P2, P3 P1-radius, P2-angle, P3-diagonal position 71 Pixelation effect P1, P2, P3 P1-num. of pixels (X), P2-num.
Appendix - DMX protocol DMX DMX Value Channel 77 Gobo zoom X fine 0-255 Zoom X fine 78 0-127 128 129-255 79 0-255 80 0 1-255 81 0-255 82 0-20 21-240 241-250 251 252 253-255 83 0 1-255 0 1-20 21-40 21-60 61-80 81-100 101-120 121-140 141-160 161-180 181-200 201-220 221-255 84 0-255 85 0-255 86 0-255 Function Type of control proportional Gobo zoom Y coarse Narrowing proportional Centre (128-default) step Widening proportional Gobo zoom Y fine Zoom Y fine proportional Synchronization to ID No function step
Appendix - DMX protocol DMX DMX Value Function Channel Out Frame Low 87 0-255 Defines the beginning of a media file segment as a percentage of the movie length (255-default) 88 Gobo control Copy mode Video stream 1 0 Play forward if dimmer (on layer 2) > 0, looping continuously 1 Play forward if dimmer (on layer 2) > 0, hold on last frame 2 Pause 3 Play forward in continuous loop 4 Play forward once and hold on the last frame 5 No function 6 Scrub (Display) the selected In Frame 7 Scrub (Display) the select
Appendix - DMX protocol DMX DMX Value Channel 50-57 58-59 60 61 62 63 64 65 66 67 68-69 70-77 78-79 88 80 81 82 83 84 85 86 87 88-89 90-97 98-99 100 101 102 103 104 105 106 107 108-109 89 Function Video Stream 2 the same functionality as for Video stream 1 Reserved Multiplication mode Video stream 1 Play forward if dimmer (on layer 2) > 0, looping continuously Play forward if dimmer (on layer 2) > 0, hold on last frame Pause Play forward in continuous loop Play forward once and hold on the last frame
Appendix - DMX protocol DMX DMX Value Channel 90 0-63 64-127 128 129-192 193-255 91 0-255 92 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 92 29 30 31 32 33 34 35 36 37 38 39 40 Function Gobo rotation and indexing Clockwise rotation from fast to slow Indexing No rotation-centre (128-default) Indexing Anticlockwise rotation from slow to fast Gobo fine indexing (rotation) Fine indexing (rotation) Gobo effect 1 Selection No effect Zoom sinus Zoom bump in fade out Zoom fade in bu
Appendix - DMX protocol DMX DMX Value Channel 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78-79 92 80 81 82 83 84 85 86 87-89 90 Function Plane Flip Y Plane Flip XY Plane mirror X top Plane mirror X bottom Plane mirror Y left Plane mirror Y right Plane mirror XY segment 1 Plane mirror XY segment 2 Plane mirror XY segment 3 Plane mirror XY segment 4 Plane tile 2x Plane tile 3x Plane tile 4x Plane tile 5x Plane cross tile 2x Plane cross tile
Appendix - DMX protocol DMX DMX Value Function Channel 92 Auto Iris effect on layer Type of control P1, P2, P3 P1-speed, P2-mask type, P3-opening/closing command 93-94 95 Reserved Zoom In/Move XY P1, P2, P3 P1-zoom, P2-X-movement, P3-Y-movement 96 Zoom In/Auto Move XY P1, P2, P3 P1-zoom, P2-X-speed, P3- Y-speed 97-99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 Reserved kaleidoscope - mode and mosaic segment selection: Square -static mode Square -dynamic mode Right triangular - static
Appendix - DMX protocol DMX DMX Value Channel 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33-39 40 96 41 42 43 44 45-49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64-67 68 69 70 Function Colour to inverse timed Cycle Cycle inverse Reserved Reserved Colour Key Colour Key inverse Key Black Key Black inverse Key White Key White inverse White flash Black flash Alpha flash Invert flash BW Flash Black and white to black and white inverse Flash Gradient Wipe X Gradient Wipe Y Reserved Gaussian filter
Appendix - DMX protocol DMX DMX Value Channel 72 Cross-stitching effect Function Type of control P1, P2, P3 P1-pattern density, P2-colour of stitch, P3- position in X-axis 73 Posterization effect P1, P2 P1-number of colours, P2-Gamma correction 74-94 95 Reserved Zoom In/Move XY P1, P2, P3 P1-zoom, P2-X-movement, P3-Y-movement 96 Zoom In/Auto Move XY P1, P2, P3 P1-zoom, P2-X-speed, P3- Y-speed 97-149 150 Reserved Layer keystoning P1,P2,P3 P1-squeezing/stretching in X, P2/P3-compressing & e
Appendix - DMX protocol DMX DMX Value Channel Function Type of control Gobo layer 3 109 0-255 110 0-20 21-240 241-250 251 252 253-255 111 111 0 1-255 0 1-20 21-40 21-60 61-80 81-100 101-120 121-140 141-160 161-180 181-200 201-220 121-255 112 0-255 113 0-255 114 0-255 115 0-255 116 0 1 2 3 4 5 Dimmer Dimmer intensity from 0% to 100% (255-default) proportional Gobo Folder selection Factory folders step User folders step Reserved Live input (grab.
Appendix - DMX protocol DMX DMX Value Function Channel 6 Scrub (Display) the selected In Frame 7 Scrub (Display) the selected Out Frame 8-9 Reserved Video stream 2 ( the same functionality as for Video stream 1): 116 10 Play forward if dimmer (on layer 3) > 0, looping continuously 11 Play forward if dimmer (on layer 3) > 0, hold on last frame 12 Pause 13 Play forward in continuous loop 14 Play forward once and hold on the last frame 15 No function 16 Scrub (Display) the selected In Frame 17 Scrub (Display)
Appendix - DMX protocol DMX DMX Value Function Channel 67 Scrub (Display) the selected Out Frame 68-69 Reserved Video Stream 2 70-77 the same functionality as for Video stream 1 78-79 Reserved Minimum mode Video stream 1 80 Play forward if dimmer (on layer 3) > 0, looping continuously 116 81 Play forward if dimmer (on layer 3) > 0, hold on last frame 82 Pause 83 Play forward in continuous loop 84 Play forward once and hold on the last frame 85 No function 86 Scrub (Display) the selected In Frame 87 Scrub (D
Appendix - DMX protocol DMX DMX Value Channel 120 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 Function Zoom fade in bump out Reserved Zoom in fade Zoom out fade Scale xy sinus Reserved Reserved Reserved XY pos. circle counter-clockwise XY pos. circle clockwise XY pos. scroll up XY pos. scroll down XY pos. scroll left XY pos.scroll right Right-left diag. down scroll Right-left diag. up scroll Left-right diag.
Appendix - DMX protocol DMX DMX Value Channel 120 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78-79 80 81 82 83 84 85 86 87-89 90 Function Plane tile 4x Plane tile 5x Plane cross tile 2x Plane cross tile 2x inverse Plane cross tile 3x Plane cross tile 3x inverse Plane cross tile 4x Plane cross tile 4x inverse Plane cross tile 5x Plane cross tile 5x inverse Plane cross tiler 5x Plane cross tiler 5x inverse Plane bar Plane bar inverse Plane bar left-righ Plane bar top-bottom Re
Appendix - DMX protocol DMX DMX Value Channel 103 104 105 106 107 108 109 110 111 112 113 Function Right triangular - dynamic mode Isosceles triangular - static mode Isosceles triangular - dynamic mode Triangular 1 - static mode Triangular 1 -dynamic mode Triangular 2 -static mode Triangular 2 - dynamic mode Centered kaleidoscope (rough)-static mode Centered kaleidoscope (rough)-dynamic mode Centered kaleidoscope (fine)-static mode Centered kaleidoscope (fine)-dynamic mode Type of control P1,P2,P3 P1,P2,P
Appendix - DMX protocol DMX DMX Value Channel 26 27 28 29 30 31 32 33-39 40 41 42 43 44 45-49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64-67 68 69 70 Function Black flash Alpha flash Invert flash BW Flash Black and white to black and white inverse Flash Gradient Wipe X Gradient Wipe Y Reserved Gaussian filter Mean filter Laplacian filter Emboss filter Sharpness filter Reserved RGB effects: RGB subtract All Pixels RGB add All Pixels RGB add non-black Pixels RGB substract/add All Pixels Swap RGB to RBG Swap
Appendix - DMX protocol DMX DMX Value Function Channel 151-199 Reserved 200 Picture merging - R/G/B gamma adjustment in blended edges Type of control P1, P2,P3 P 1- red, P 2 - green, P 3- blue 201-255 Reserved 125 Gobo effect 2 -Parameter 1 0-255 Effect control depends on effect 126 Gobo effect 2 -Parameter 2 0-255 Effect control depends on effect 127 Gobo effect 2 -Parameter 3 0-255 Effect control depends on effect 128 Gobo Position X coarse 0-127 Movement forward proportional 128 Centre (128-default)
