Operating Instructions BLUE ARROW 1.0 3D RTF 2.4 GHz No.
Operating Instructions, BLUE ARROW 1.0 3D RTF 2.4 GHz No.
Operating Instructions, BLUE ARROW 1.0 3D RTF 2.4 GHz No. S2523 Explanation of specialist terms: Climb and descent ("collective pitch / throttle"): This controls the model's climb and descent. Yaw: The model's movement around the vertical axis; the helicopter rotates to right or left.
Operating Instructions, BLUE ARROW 1.0 3D RTF 2.4 GHz No. S2523 Be sure to read right through these Safety Notes before you build your model. Always keep to the procedures and settings recommended in the instructions. If you are operating a radio-controlled model aircraft, helicopter, car or boat for the first time, we recommend that you enlist the aid of an experienced modeller to help you. Safety Notes Radio-controlled models are not toys in the usual sense of the term.
Operating Instructions, BLUE ARROW 1.0 3D RTF 2.4 GHz No. S2523 Use only those components and accessories which we specifically recommend. Do not carry out modifications to the radio control system components apart from those described in the instructions. Operating the model • Never fly over or towards spectators or other pilots, and maintain a safe distance from them at all times. • Never endanger people or animals. • Never fly or run the model close to high-tension overhead cables or residential areas.
Operating Instructions, BLUE ARROW 1.0 3D RTF 2.4 GHz No. S2523 Dear Customer, Congratulations on choosing a factory-assembled model helicopter from our range. Many thanks for placing your trust in us. The model can be completed and made ready to fly very quickly. Please read right through these instructions before attempting to fly the model for the first time, as this will make it much easier to operate the model safely.
Operating Instructions, BLUE ARROW 1.0 3D RTF 2.4 GHz No. S2523 Transmitter description* (Mode 1) - The mode select switch** is located on the back of the transmitter (*Complete operating instructions for the J6 transmitter can be found in the Download area at www.robbe.
Operating Instructions, BLUE ARROW 1.0 3D RTF 2.4 GHz No. S2523 Transmitter description* (Mode 2) - The mode select switch** is located on the back of the transmitter (*Complete operating instructions for the J6 transmitter can be found in the Download area at www.robbe.
Operating Instructions, BLUE ARROW 1.0 3D RTF 2.4 GHz No.
Operating Instructions, BLUE ARROW 1.0 3D RTF 2.4 GHz No.
Operating Instructions, BLUE ARROW 1.0 3D RTF 2.4 GHz No. S2523 Charging the flight battery Connect the battery charger to the mains PSU, and plug the PSU into a mains socket. The LED on the power supply will illuminate. Connect the battery to the charger using the adapter lead, and use "+" or "-" to set the charge current (high = fast, low = longer battery life). Press the Start button: the monitor LED flashes.
Operating Instructions, BLUE ARROW 1.0 3D RTF 2.4 GHz No. S2523 Flight preparation Open the battery compartment and insert dry or rechargeable cells. Close the battery compartment. Move all the switches to the forward position, and switch the transmitter on (Fig. 1). If switch "A" or "B" is at the "ON" position, the screen will flash, and you will hear a "beep".
Operating Instructions, BLUE ARROW 1.0 3D RTF 2.4 GHz No. S2523 Flight preparation Check the correct position of the swashplate before the first flight. The swashplate must sit exactly horizontal when viewed from the side and front of the model. Position the model on a totally flat surface. Now move the throttle stick to the lowest throttle position, and switch the transmitter on. Switch the transmitter on. Check that the pitch-axis, roll and tail rotor trim are all in the neutral positions.
Operating Instructions, BLUE ARROW 1.0 3D RTF 2.4 GHz No. S2523 Trim adjustments, Mode 1 Trim adjustments, Mode 2 Throttle trim: If the rotor starts to move without the throttle stick being touched, or does not respond to stick movements, you must adjust the throttle trim until the rotor is stationary. Throttle trim: If the rotor starts to move without the throttle stick being touched, or does not respond to stick movements, you must adjust the throttle trim until the rotor is stationary.
Operating Instructions, BLUE ARROW 1.0 3D RTF 2.4 GHz No.
Operating Instructions, BLUE ARROW 1.0 3D RTF 2.4 GHz No. S2523 Important Notes The first few flights Take-off: use the 3D switch for aerobatics only. To take off, slowly and steadily increase rotor speed until the model is hovering approximately at eye-level. At the same time adjust the trims until it is flying stably and hovering over one point. At low height (approx. 10 - 15 cm above the ground) the model cannot be trimmed accurately due to the turbulence generated by the rotor.
Operating Instructions, BLUE ARROW 1.0 3D RTF 2.4 GHz No.
Replacement parts list, BLUE ARROW 1.0 3D RTF 2.4 GHz No.
Replacement parts list, BLUE ARROW 1.0 3D RTF 2.4 GHz No. S2523 Replacement parts list, BLUE ARROW 1.0 3D RTF NE250920 NE250921 NE250922 NE250923 NE250924 NE250925 NE250926 Order No.
Operating Instructions, BLUE ARROW 1.0 3D RTF 2.4 GHz No. S2523 robbe Modellsport GmbH & Co. KG hereby declares that this device conforms to the fundamental requirements and other relevant regulations of the appropriate CE Directive. Under www.robbe.com, you will find the original Conformity Declaration by clicking on the Logo button "Conform" shown together with the appropriate device description.
