Version No.: 2631 Version No.: 2652 INSTRUCTIONS AND USER MANUAL www.robbe.
INSTRUCTIONS AND USER MANUAL GENERAL INFORMATION • The model is designed for the components specified by us. Unless otherwise stated, servos and other electronic components are designed for standard supply voltage. Recommended cell count for Lipo batteries also refers to standard Lipos voltage of 3.7V per cell. If you use other servos, a different motor and controller, batteries, or propellers, please make sure they fit first. In the event of deviations, corrections and adjustments must be made by yourself.
INSTRUCTIONS AND USER MANUAL CONFORMITY FLIGHT INSTRUCTIONS • • • • • • • • • • • • Modellbau Lindinger GmbH hereby declares that this device complies with the essential requirements and other relevant regulations of the corresponding CE directives. The original declaration of conformity can be found on the Internet at www.robbe.com, in the detailed product view of the respective device description or on request. This product can be operated in all EU countries.
INSTRUCTIONS AND USER MANUAL Technical data Wingspan: ca. 1460 mm Lenght: ca. 1220 mm Total wing area: ca. 36,5 dm 2 Total weight: ca. 1380 g Battery: Lipo 3S/2100mA ESC: 40A, 5V/3A-BEC, 2-3S Lipo Servo: 5x10g (22,5x11,5x22,7 mm) Propeller: 10x5“ Accessories not included but required Item. Discription -No. - Suitable remote control, 4 channel In connection with the illustrations and the corresponding short texts, get an overview of the respective building steps.
INSTRUCTIONS AND USER MANUAL Picture 1 - 2 Install the main landing gear with the M3x16mm screws on the fuselage. 5 4 6 Picture 3 - 7 Put the prop hub onto the motor shaft. Then mount the spinner backplate, the prop,washer and nut. Tighten the nut carefully but firmly to avoid it gets loose in flight.
INSTRUCTIONS AND USER MANUAL 8 Picture 8 Make sure that there is a small gap between the spinner back plate and the cowling so that the spinner does not rub against the cowling. 10 Picture 10 Assembly of the tail. Temporarely remove the securing clips from the linkages. Picture 9 Finally, install the spinner with the M2,5x8mm screws. 9 ENGLISH 6 Picture 11 - 13 Now put the vertical fin into the support of the horizontal stabilizer, as shown.
INSTRUCTIONS AND USER MANUAL 17 Pictures 17 - 19 Connect the elevator and rudder linkage to the outer bore of the control horns and secure it with the secure clips, removed before. 18 19 ENGLISH 16 Picture 14 - 16 Put the assembled tail on the fuselage and fix it by a M3x22mm screw.
INSTRUCTIONS AND USER MANUAL 20 Pictures 20 - 22 Wing assembly. Put the carbon wing joiner into the right wing and then put the left wing onto the win joiner and push both halves together. 24 Pay attention to the servo wires, which have to be guided to the bottom side of the wing. 21 22 ENGLISH 8 23 Picture 23 Insert the plastic lock from above. 25 Picture 23 - 24 Connect both aileron cables with a V-cable.
INSTRUCTIONS AND USER MANUAL 26 Picture 26 - 28 Place the wing on the fuselage by first attaching the two wing plugs to the front of the fuselage. Make sure that the servo cables are not trapped between the fuselage and the wing. 29 Fix the wing to the fuselage with the wing screws. 27 Picture 29 - 31 Open the battery hatch cover in front of the canopy and install the battery. Switch on the radio and make sure, the throttle stick is in lowest position. Connect the battery to the ESC.
INSTRUCTIONS AND USER MANUAL 32 Picture 34 - 36 Picture 34 shows an example of a Mode 2 transmitter for the rudder settings. Please refer to the operating instructions of your transmitter as well as the mode setting you have selected. Switch for cargo hatch 34 Full throttle Rudder left Check that all rudders are moving correctly. Operate all functions on the transmitter one after the other.
INSTRUCTIONS AND USER MANUAL Notes on operation 1. Direction of control surfaces Before the first flight of the model, the direction of all rudders must be checked. Elevator If the elevator stick is pulled back by the transmitter, the elevator must deflect upwards. If the elevator stick is pushed forward, the elevator must deflect downwards. Finally, the center of gravity must be checked on the model. All components (including the battery) are mounted in the model.
INSTRUCTIONS AND USER MANUAL CONTROLLER PROGRAMMING 1. Technical data ESC: Typ Cont. current Boost current BEC-Modus BEC-output (max. 10 Sec.) -40A 40A 55A Linear 5V/3A No. of cells LiPo NiMH 2-3S 5-9 Weight Measurements mm 39g 68x25x8 2. Programmable adjustments: 1. Brake: enabled / Disabled 2. Battery type: Lipo / NiMH 3. undervoltage protection (Cut-Off Mode): Soft Cut-Off (Gradual reduction of power) / Cut-Off (Immediate standstill) 4.
INSTRUCTIONS AND USER MANUAL Throttle adjustment: (The gas range should be reset each time the remote control is changed.) 1. Switch on the radio with throttle stick up (full). 2. Connect flight battery and wait for approx. 2 sec. 3. A „beep“ sound should be heard, this confirms the setting of the full throttle position. 4. Put the throttle stick to lowest position, more „beep“ sound should be heard, whichshow the number of cells 5.
INSTRUCTIONS AND USER MANUAL 5. Programming the ESC with the transmitter (4 steps) Note: Please note that the throttle curve is set to 0%, the throttle lever to neutral position and the deflection to 100%. 1. Start programming mode 2. Select program point 3. Setting the program point (value) 4. Exit programming mode. 1. Start programming mode 1) Switch on transmitter, set throttle stick to full throttle, connect battery to ESC 2) Wait 2 sec., a double „beep“ must be heard 3) Wait another 5 sec.
INSTRUCTIONS AND USER MANUAL ENGLISH FOR YOUR NOTES 15
DISTRIBUTOR Modellbau Lindinger GmbH Industriestraße 10 4565 Inzersdorf im Kremstal Austria Phone: +43(0)7582/81313-0 Mail: info@robbe.com UID No.: ATU69266037 „robbe Modellsport“ is a registered Trademark by Modellbau Lindinger GmbH Errors, misprints and technical changes reserved. Copyright 2019 Modellbau Lindinger 2019 Copy and reprint only with our permission. Service-Address Contact your Dealer or: Modellbau Lindinger GmbH, Industriestraße 10, 4565 Inzersdorf im Kremstal service@robbe.
