Instructions for use

ENGLISH
9
INSTRUCTIONS AND USER MANUAL
Modellsport
PREFACE
Milan the electric glider in classic Laser-Cut wood construction. Design by: Pietro Tescari.
Milan is an elegant electric glider in the 2-meter class that responds excellently to thermals. Construc-
ting the Milan is easy, due to the laser cut wooden parts. The well thought out construction, leads to
a quick assembly. The balsa wood planking on both sides of the wings, from the leading edge to the
main spar, results in a light and but stiff construction. The wing is constructed in 3 parts with a middle
section and slip-on wings. This allows the model to be conveniently transported.
The fuselage is built in the classic stable wooden construction. The curved side panels provide an
elegant appearance. The tail unit is screwed to the fuselage and can be removed if desired. This ma-
kes the Milan not only an electric glider suitable for everyday use, but also the ideal companion for
holidays. The Milan is equipped with a light brushless motor (such as the Ro-Power Torque 2834/880KV)
which uses an 11 x 8“ folding propeller. The 2100 mAh 3s LiPo battery is inserted into the fuselage over
a removable fuselage cover.
TECHNICAL DATA
BOX CONTENT / NEEDED ACCESSORIES
Span 1960 mm
Flying weight ab. 990 g
Wing Area 33,75 dm²
Wing Load ab 26,4g/dm²
Airfoil S 3021
Designed as 4-ap wing
C.G. 65 mm
Elevator yes
Rudder yes
Ailerons yes
Flaps yes
Landing aps no
Motor yes
FLIGHT INSTRUCTIONS
• Before the rst ight, observe the instructions in the „Safety Instructions“ section.
• When ying the model, you should choose a day with as little wind as possible
• A large, at area without obstacles (trees, fences power lines etc.) is suitable for the rst ights.
• Please carry out a functional test of the drive train / power set and remote control.
• After assembling the model on the aireld, check once again that all model components such as
wing, tail units, wing mounts, engine, linkages, etc. are rmly and properly fastened.
• For a hand start a helper should be present, who can throw the model with enough thrust into the
air.
• The start usually takes place against the wind.
• Do not stall the model near the ground
• Do not initiate tight turns in the immediate vicinity of the ground.
• Check the reactions of the model to the rudder deections. If necessary, adjust after landing to
increase or decrease the deections accordingly.
• The minimum ight speed must be at an adequate safety altitude.
• Initiate the landing with sufcient speed
SAFETY INSTRUCTIONS FOR RECHARGEABLE BATTERIES
• Do not immerse the battery in water or other liquids.
• Do not heat, throw into re or microwave.
• Do not short-circuit or charge with reversed polarity
• Do not expose, deform or throw the battery
• Do not solder directly on the battery
• Do not change or open the battery
• Only charge the battery with suitable chargers, never connect it directly to a power supply unit.
• Never charge or discharge the battery or charger on a ammable surface.
• Never leave the battery unattended during charging or discharging processes.
• Never charge or discharge the battery in direct sunlight or near heaters or re.
• Do not use the battery in places subject to high static discharge.
All this can cause the battery to be damaged, explode or even catch re!
• Keep the battery away from children
• Keep leaked electrolyte away from re, as it is highly ammable and may ignite.
• The electrolyte liquid should not get into the eyes, if it does, rinse immediately with plenty of clear
water and then see a doctor.
• The electrolyte liquid can also escape from clothes and other objects with a lot of water or washed
off.
• Observe the safety instructions of the battery manufacturer and the charger manufacturer.
The Milan allows an easy adjust of the center of gravity without the need for a trim weight. With
approx. 980g take-off weight, a safe hand launch is possible. After approx. 15 - 20 sec. of throttle,
you can easily reach a ight altitude of approx. 150 m. Even small thermals can be easily own with
the Milan. In addition to the ailerons in the outer wings, the wing middle section has aps that can
be extended up to 90°. This allows safe landings on small landing elds despite the excellent glide
characteristics.
Key Features:
• Wooden construction from lasered components
• Wings in modern comb spar construction with stable leading edge
• Robust construction for high suitability for everyday use
• Good to very good thermal performance
• Inexpensive power set-up with very long motor running time
• 3-part Wings, with easy assembly of the outer wings with magnet support
• Easy to remove tail unit
• Easily accessible battery compartment through removable cover
• Very easy to land due to the included 90° movable aps
Item
number
Needed accessories
ARF
LF
PNP
LF
Motor 5831 RO-POWER TORQUE 2834/880 K/V
- X
ESC 8713 RO-CONTROL 3-40 2-3S -40(55)A 5V/3A BEC
- -
Battery 7337 RO-POWER ULTRA HP 2100MAH 11,1 VOLT 3S
- -
Servo ELE S0009 ROVOR SERVO S0009
- X
Servo RUD S0009 ROVOR SERVO S0009
- X
Servo AILE S0009 ROVOR SERVO S0009 (2x)
- X
Servo FLAP S0009 ROVOR SERVO S0009 (2x)
- X
Adhesives 5019 ROBBE Speed instant glue set
- -
Epoxy resin 50604 ROBBE RO-POXY 10 MINUTE EPOXY RESIN ADHESIVE 190G
- -
Extension cable -
yes 2x Extension cable for servo aile
yes 2x Extension cable for servo ap
- X
Propeller+Spinner 26530003 FOLDING PROPELLER set 11x8“ with spinner 38mm
- X
TX - min. 5 channels
- -
RX - min. 5 channels
- -
Declaration:
LF: Box content
- : not included X: included