barroom User Manual Before operating this unit, please read the user manual completely and keep it. If the manual is lost, you can send e-mall 10 oversampling corn, request for an electronic manual.
ROAM | Range Hood READ AND SAVE THESE INSTRUCTIONS Dear users: Thank for your buying our range hood. Please accept our best regards. Please read this user manual carefully before installation and pictures in this manual only for your reference. If the picture isn't accord with object, subject to object. We keep to right to update appearance, structure or products without notice.
ROAM | Range Hood A Danger Please turn off range hood immediately if pan got fire (range hood shall aggravate fire if it's working) and extinguish fire by effective action. Strict. For example, cover flame by metal cover, turn off gas valve immediately Execution ang remove inflammable things. Any abnormal, please turn off power, take off plug or cut off electric Strict source, and contact service. It's possible to cause electric shock or fire if Execution Using range hood under abnormal situation. /\ Warmin
ROAM | Range Hood /A\ Warning All operation must comply with our safety guidelines as well as local Strict safety regulations. Execution There shall be adequate ventilation of the room when the range hood is Strict used at the same time as appliances burning gas or other fuels. Execution For Residential Use Only.And it's not allowed to exhaust dangerous or Strict explosive matter or air. It should be put under dry and ventilation Execution environment without dangerous air.
ROAM | Range Hood /\ Warning Strict Execution TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE: a) Never leave surface units unattended at high settings. Boil overs cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings. b) Always turn hood ON when cooking at high heat or when flambeing food (i.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambe'). c) Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter.
ROAM | Range Hood /\ Warning Strict Execution Do not use an extension cord. If the power supply cord is too short, have a qualified electrician install an outlet near the appliance. Strict Execution This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
ROAM | Range Hood A Notice Accessible parts may become hot when used with cooking appliances. Strict Execution DISPOSAL: Do not dispose this product as unsorted municipal waste. Collection of such waste separately for special treatment is necessary. This product must not be disposed together with the domestic waste. This product has to be disposed at an authorized place for recycling of electrical and electronic appliances.
ROAM | Range Hood Size EE EE E 18s TRY 5:18 E The size marked Is for reference only. Packing List Please check the items in the container upon unpacking Standard Offerings 4 1 , Flexible aluminum duct [] 1 Range hood User Manual
ROAM | Range Hood Installation A Warning 1.The alr must not be discharged Into a flue that Is used for exhausting fumes from appliances booming gas or other fuss, the discharge of air must fulfill the requirements of local regulations. 2.Note that when installing the metal expansion pipe, the pipe shall match with the hole in size. Overlarge hols is prohibited, as twill resulting loose pipe and accidental drops. 3.
ROAM | Range Hood Notice @ Installation and circuit setting must be done by experienced professionals. Only a professionally trained person with an installation qualification can install the hood. Non-professionals are not allowed to install, dismantle and repair the hood. @Please do not power on the hood before installation to avoid electric shock.
ROAM | Range Hood 3. Determine the positions to fix the hitching leg and the hitching leg stop block. Note: The hitching leg must be fixed on the beam with a screw. With the stove bearing surface as the base, mark the drill holes in the corresponding position of the wall according to the distance from the hitching leg hole to the bottom of the machine, and the height of the bottom of the hanging cabinet. The relevant size is given as below: 1).
ROAM | Range Hood 6. The installation of the drawing panel torsional spring on the attached panel of the main engine mainly includes the following steps : 1). Firstly, put torsional spring rubber sleeve on drawing panel torsional spring, then put torsional spring case on drawing panel torsional spring. 2). Firstly put drawing panel torsional spring into put torsional spring into nut-insert finally, fix torsional spring lining and nut-insert with M4x10 screw, 3).
ROAM | Range Hood 10. At this time, there is still a certain gap between the attached panel of the mainframe and the roof, so the attached panel of the mainframe should be pulled out and pushed to contact with the roof, and then the attached panel of the mainframe should be fixed on the roof with ST4.2x18 screws. 4 LA 11. After installation, the whole machine must be kept horizontal. In the end, insert the oil cup inch the hitching leg on the bottom of the mesh enclosure and power it for trial operation.
ROAM | Range Hood 4. Drill a hole deep (not too large) at the mark with a drill bit with a diameter of press the expansion pipe Into the hole, use the 4x60mm wood screws provided with the machine to securely fix the hanging feet.Drill a hole with a diameter of too large) and a depth of at the fixing hole mark of the hitching lag stop block, and insert the M6 metal expansion pipe into the hole. SY(235mm) Hitching foot Ae] Pn [235 Emm) (110mm) (55mm) | 24-1348" (630mm) pe (650-750mm) 3112-35hd” {800-800mm) 5.
barroom Range Hood 7. The Installation of the drawing panel torsional spring on the attached panel of the main engine mainly Includes the following steps : 1). Firstly, put torsional spring rubber sleeve on drawing panel torsional spring, then put torsional spring case on drawing panel torsional spring. 2). a Firstly put drawing panel torsional spring into put torsional spring into nut-insert. finally, fix torsional spring lining and nut-insert with M4x10 screw. 3).
ROAM | Range Hood 11. After installation, the whole machine must be kept horizontal. In the end, insert the oil cup into the hitching leg on the bottom of the mesh enclosure and power it for trial operation.
ROAM | Range Hood The machine has a cleaning reminder function. When the range hood has operated for 80 hours, the cleaning prompt icon will be on for a long time, and the buzzer will sound to remind the user of oil net cleaning. At this time, the use may cancel the prompt by extended pressing the button; otherwise, the cleaning prompt icon will be on for 1 hour and then extinguish automatically. The use can also query the elapsed time of motor operation by extended pressing the “Turbo” button in off state.
ROAM | Range Hood Lamp removal 1. Unplug the power plug; 2. Embed a small Flathead screwdriver ar something sharp and small in the installation gap between lamp shade and vassal hood, and force outward to take out the spotlight from the vessel hood: 3. Pull out the lamp connector terminal and replace the spotlight; Lamp image Lamp information Lamp Type Rectangular LED = (280mm 124mm Max Power vote ows wet = Dimension soe the lamp Image Switch removal 1. Take down the oil cup with both hands at first; 2.
ROAM | Range Hood Bs. ¥ Removal Steps of Body 1. Pull out the plug; 2. Take down the oll cup; 3. Loosen drawing panel torsional spring in accordance, then insert drawing panel into decorative panel; 4. Unscrew the four screws from the back of the decorative panel. Remove the decorative panel and drawing panel. 5. Remove the noise absorption sponge from both side; 8. Use a Phillips screwdriver to unscrew 4 screws from the top and both side of acoustic baffle, then remove the acoustic baffle. 7.
ROAM | Range Hood Circuit Diagram Electrical Connection Diagram: black , Control circuit A red white W a red V g black 120v~80Hz N — Troubleshooting of General faults Serial number Fault Cause Solution ho response after pressing any icon The r plug is not connected 1 e.g.
