User Manual

RND 315-00005, 315-00006, 315-00013 — AC-DC DIN RAIL MOUNTED POWER SUPPLY
4 5
OUTPUT
PARAMETER CONDITIONS MIN TYP MAX UNITS
Output voltage accuracy
±1 %
Output voltage adjustment
range
IS50-12
IS50-24
IS50-48
11.6-12.3
23.5-24.5
47.5-48.3
V
V
V
Output voltage can be adjusted within above range by V-ADJ. variable
resistance inside of the power supply. When output voltage exceeds
the range, the power supply will be in failure or get into over voltage
protection mode. To avoid the case that the output voltage is higher
than rated voltage, output current should be used under rated current
Minimum load 0 A
Line regulation Vin fro
m 100Vac to 240Vac 1
%
Load regulation Vout from min. to max. 1
%
Turn-on delay time Full load, Vin=115Vac 560 ms
Hold up time Full load, Vin=115Vac 20
ms
PRODUCT SPECIFICATION
Updated 2016-V1.0-1206
din rail power supply
www.pairuigroup.com
Page:4/17
PAIRUI ELECTRONICS
Protection
Short circuit
Shut off output voltage, the power supply will recover after the power is turned
on again
Over voltage
IS50-12: over voltage protection value 20V
IS50-24: over voltage protection value 33V
IS50-48: over voltage protection value 66V
(1) When output voltage exceeds above over voltage protection value or reversal
voltage occurs, the protection will be started and the output voltage will be cut
off in order to protect the power supply;
(2) The power supply will recover after the power is turned on again
Over current
IS50-12: over current protection valu
e 6A
IS50-24: over current protection value 3A
IS50-48: over current protection value 1.5A
(1) When output voltage exceeds above over current protection value, the
protection will be started and the output voltage will be cut off in order to
protect the power supply;
(2) The power supply will recover automatically after the fault condition is
removed
Over
temperature
Over temperature protection value: 100±10℃
(1) When the ambient temperature exceeds above over temperature protection
value, the protection will be started and the output voltage will be cu
t off in
order to protect the power supply;
(2) The power supply will recover after the power is turned on again
PRODUCT SPECIFICATION
Updated 2016-V1.0-1206
din rail power supply
www.pairuigroup.com
Page:5/17
PAIRUI ELECTRONICS
RND 315-00005
RND 315-00006
RND 315-00006:
RND 315-00006:
Protection
Short circuit
Shut off output voltage, the power supply will recover after the power is turned
on again
Over voltage
IS50-12: o
ver voltage protection value 20V
IS50-24: over voltage protection value 33V
IS50-48: over voltage protection value 66V
(1) When output voltage exceeds above over voltage protection value or reversal
voltage occurs, the protection will be started and the output voltage will be cut
off in order to protect the power supply;
(2) The power supply will recover after the power is turned on again
Over current
IS50-12: over current protection value 6A
IS50-24: over current protection value 3A
IS50-48: over current protection value 1.5A
(1) When output voltage exceeds above over current protection value, the
protection will be started and the output voltage will be cut off in order to
protect the power supply;
(2) The power supply will recover automatically after the fault condition is
removed
Over
temperature
Over temperature protection value: 100±10℃
(1) When the ambient temperature exceeds above over temperature protection
value, the protection will be started and the output voltage will be cut off in
order to protect the power supply;
(2) The power supply will recover after the power is turned on again
PRODUCT SPECIFICATION
Updated 2016-V1.0-1206
din rail power supply
www.pairuigroup.com
Page:5/17
PAIRUI ELECTRONICS
RND 315-00005:
RND 315-00005:
Protection
Short circuit
Shut off output voltage, the power supply will recover after the power is turned
on again
Over voltage
IS50-12: over voltage protection value 20V
IS50-24: over voltage protection value 33V
IS50-48: over voltage protection value 66V
(1) When output voltage exceeds above over voltage protection value or reversal
voltage occurs, the protection will be started and the output voltage will be cut
off in order to protect the power supply;
(2) The power supply will recover after the power is turned on again
Over current
IS50-12: o
ver current protection value 6A
IS50-24: o
ver current protection value 3A
IS50-48: over current protection value 1.5A
(1) When output voltage exceeds above over current protection value, the
protection will be started and the output voltage will be cut off in order to
protect the power supply;
(2) The power supply will recover automatically after the fault condition is
removed
Over
temperature
Over temperature protection value: 100±10℃
(1) When the ambient temperature exceeds above over temperature protection
value, the protection will be started and the output voltage will be cut off in
order to protect the power supply;
(2) The power supply will recover after the power is turned on again
PRODUCT SPECIFICATION
Updated 2016-V1.0-1206
din rail power supply
www.pairuigroup.com
Page:5/17
PAIRUI ELECTRONICS
RND 315-00013
47.5 - 48.3
RND 315-00013:
over voltage protection value 60V
RND 315-00013:
over voltage protection value 1.5V