User Manual

O/P Current "A":
Press "Display Key" for 1 seconds while displaying "V" to display
the O/P current (charging current) value.
Battery Level "P":
Press "Display Key" for 1 seconds while displaying "A" to display
the Battery Capacity (battery level) value.
O/P Current Adjustment (this will not change real O/P current):
Press and hold "Display Key" for 3 seconds while displaying "P" to
enable O/P current adjustment (for authorized technicians only).
Upper Bar twinkle:Press "Display Key" to increase the value.
Bottom Bar twinkle: Press"Display Key" to decrease the value.
Press and hold "Display Key" for 3 seconds to save the new value.
Total Charging Capacity "AH" (Ampere-Hour):
Start AH calculation when charging current >1A, "H" twinkle when "AH"
function operating. Press and hold "Display Key" for 3 seconds while
displaying "H" to enable AH to zero. "H" stop twinkle when "AH"
function stop operating.
Timer time:
Start counting after "AH" function operating.
Charging Timer Setting (0.1H-0.2H-0.3H-):
Start timer when voltage >setting value or current <30% of rating. Press
& hold "Display Key" for 3 seconds while displaying "E" to enable timer
setting. (Upper Bar: increase; Bottom Bar: decrease) Press and hold
"Display Key" for 3 seconds to save the new setting value. The 3rd dot
signal flashes light means the timer is starting and while the timer stop
the 3rd dot signal solid lights.
Descriptions (Ver: 2.34)
O/P Voltage "V":
Preinstall demonstration.
Item
Timer time:
Star counting after "E" (timer) function operating. When o/p current under
setting value, the 2nd dot signal flashes. It will display the total time of
charge after battery has been full charged. According to the value, the
user can setting the perfect charging time for his own battery. Ex. If the
total time is 1 hour, user can setting the value at 1.0.E.
Item
Descriptions (Ver: 2.34)
CPU Running
=Voltage
=Amperage
=Percent
=AH
=time
Timer Starting
Upper Bar (Increased)
Bottom Bar (Decreased)
=End time
=hours
=Pre-Charger
Display Key
Reset Key
Display Change: 1 second
Increased/ Decreased change: 2 seconds
Setting & Save: >3 seconds
1.Current <30% of rating, the display will show "x.x h.". If the charging
current drop to <10% of rating current, the timer will stop automatically
and the timer will show the total charging time from 30% to 10% of
rating current.
2. When over timer setting but current >10% of rating, the display will
show "x.x.h." (The 2nd dot signal solid light means that the charger
switch to float charging stage is by timer setting not current setting)
When the charger displays "x.x.h." or "x.x h." and green LED lights,
you can press "Display Key" to reset the display to "V" (voltage)
Float Charging:
High Voltage (Over Charging):
If the battery voltage over the setting value, the display will show "H.V." &
"xx.xV" alternately, meanwhile, the charger will switch to float charging
stage & LED green lights. It will charge battery again (reset) while the
battery voltage down to the normal voltage.
Pulse Charging Stage: The charger will swtich to pulse charing stage when the charging current
is >50% of rating current. The pulse charging stage will be kept about 30 seconds and then go to
pre-charging stage and 20 seconds later go to conatant current charging stage.
Pre-charging:
When battery voltage < setting value, the pre-charge timer start counting.
Press & hold "Display Key" for 3 seconds while displaying "C" to enable
timer setting (Upper Bar: increase; Bottom Bar: decrease, each step will
increase or decrease 0.1 hour). Press & hold "Display Key" for 3 seconds
to save the new setting value.
Automatic Baery Charger
Specications & User Manual
Distrelec Schweiz AG, Grabenstrasse 6, 8606 Nänikon, Switzerland, T [phone], [e-mail], distrelec.com