Datasheet

Heat Shrink End Cap
RND is a trademark of Distrelec
Scope
This approval specifies technical requirement, package, storage and specification of the heat shrink cable end caps.
Standards
• ASTM-D-638 (GB/T 1040) - Standard test methods for tensile properties of plastics
• IEC 60243 (GB/T 1408) - Electrical strength of insulating materials-Test methods
• IEC 60093 (GB/T 1410) - Methods of test for volume resistivity and surface resistivity of
solid electrical insulating materials
• ISO 974 (GB/T 5470) - Plastics-Determination of the brittleness temperature by impact
• ASTM-D-5510 (GB/T 7141) - Plastics-Methods of heat aging
Technical Requirements
Product properties
RND heat shrink end caps are made of cross-linked polyolefin. It can be applied on de-energized power cables as a watertight sealing, electrical
insulation and mechanical protection cover. It is coated with hot-melt adhesive to ensure reliable seal of cable ends.
Standard color: Black
Appearance
The surface of the end cap should be smooth and clean, and free of pinholes or cracks visible to the unaided eye
Heat shrink properties
• Start to shrink at 90℃, and fully recovered at 130℃
• Radial shrink ratio: ≥ 50%
• Wall thickness non-uniformity: ≤35%
Technical Requirements
These products are non-hazardous. Keep in clean, cool, dry, well-ventilated storage area. During transportation and storage, pay attention to
rain and sun and keep away from sources of ignition
Physical and Chemical Properties
WƌŽƉĞƌƚLJ
dĞƐƚDĞƚŚŽĚ
^ƚĂŶĚĂƌĚsĂůƵĞ
dĞŶƐŝůĞ^ƚƌĞŶŐƚŚ ^dDͲͲϲϯϴ шϭϮDWĂ
ůŽŶŐĂƚŝŽŶĂƚƌĞĂŬ ^dDͲͲϲϯϴ шϯϬϬй
dĞŶƐŝůĞ^ƚƌĞŶŐƚŚsĂƌŝĂƚŝŽŶĨƚĞƌ,ĞĂƚŐŝŶŐ（ϭϯϬ℃ пϭϲϴŚ）
^dDͲͲϱϱϭϬ
чцϮϬй
ůŽŶŐĂƚŝŽŶĂƚƌĞĂŬsĂƌŝĂƚŝŽŶĨƚĞƌ,ĞĂƚŐŝŶŐ
^dDͲͲϱϱϭϬ
чцϮϬй
（ϭϯϬ℃пϭϲϴŚ
）sŽůƵŵĞZĞƐŝƐƚŝǀŝƚLJ
/ϲϬϬϵϯ
шϭпϭϬ
ϭϯ
ɏͼĐŵ
ŝĞůĞĐƚƌŝĐ^ƚƌĞŶŐƚŚ
/ϲϬϮϰϯ шϭϱŬsŵŵ
ƌŝƚƚůĞƚĞŵƉĞƌĂƚƵƌĞ
/^Kϵϳϰ
чͲϰϬ℃