Datasheet

Specifications and Test Methods
No Item Test Method Specification
1 Capacitance
The capacitance shall be measured at 25°C at the
frequency and voltage shown below:
Type
Item
NPO
(≦1nF)
NPO>1nF,
Y5V,
X7R/X5R
C≧10uF
Freq.. 1±0.1M z 1±0.1KHz 120H
Voltage 1±0.2Vrms 1±0.2Vrms 0.5±0.2
Vrms
Within the specified tolerance
Remark: For ClassII(X7R/X5R,Y5V),
Before initial test, please perform
De-aging process as below:
Heat up to 150℃ for 1Hr and then set
form 48±4 Hrs at room temp.
2 Q value /
Dissipation
Factor
D.F. shall be measured at 25°C at the frequency and voltage
shown a o.1
NPO:
C＜30pF : Q value ≧400+20C
C≧30pF : Q value ≧ 1000
X7R/ X5R :
Vr=50V~6KV, DF≦2.5%
Vr=
25V, DF≦3.5%
Vr=16V, DF≦3.5%
Vr=
10V, DF≦5.0%
Vr=
6.3V, DF≦10.0%
Y5V:
Vr=≧50V, DF≦5.0%
Vr =25V, DF≦7.0%
Vr=16V(C＜1.0uF), DF≦7.0%
Vr=16V(C≧1.0uF), DF≦9.0%
Vr=10V, DF≦12.5%
Vr=6.3V, DF≦20%
( see EXCEPTION at left side)
EXCEPTION OF D.F.
X7R/X5R
r D.F Exception of D.F.
≧
50V
≦3.5%
1206≧0.47uF
25V
≦7%
1206≧4.7uF
≦10%
1206≧6.8uF
16V
≦5%
1206≧2.2uF
≦10%
1206≧4.7uF
10V
≦10%
1206≧2.2uF
Y5V
Vr D.F Exception O.F.
≧50V
≦7%7%
1206≧4.7uF
16V
(≧1uF)
≦12.512.5%
1206≧10uF
3 Insulation
Resistance
Rated voltage ≦100V : Apply RV for 120 sec.
Rated voltage 200-630V : Apply RV for 60 sec.
Rated voltage 1KV-6KV : Apply 500V fo 60 sec.
NPO : ≧ 10GΩ or
500Ω-F(whichever is smaller)
X7R/X5R, Y5V : ≧ 10GΩ or 100Ω-
F(whichever is smaller)
4 Dielectric
Strength
Test voltage(Vt): (Duration 1～5 seconds.)
Vt= Vr X250% (Vr≦100V) Charge current: ≦ 50mA
Vt= Vr X200% For product Vr=200V/250V
Vt= Vr X150% For product Vr=500V~999V
Vt= Vr X120% For product Vr=1KV~3KV
Vt= Vr X110% For Vr≦5KV, Vt= Vr X100% For Vr＞5KV
No evidence of damage or
flash over during test.
5 Solderability
*Solder temperature : 235±5°C
*Dipping time : 2±0.5 sec.
95% min. coverage of all metalized area
Multilayer Capacitors , SMD
Distrelec Schweiz AG, Grabenstrasse 6, 8606 Nänikon, Switzerland, T [phone], [e-mail], distrelec.com