Datasheet

ManualsBrandsRND Components ManualsLEDsBi-Colour THT LED 5mm Green-Yellow / Red G 573nm, R 632nm T-1 3/4

Bi-Colour LED, 5 mm

Features

Device Selection Guide

Part No. Emitting Color Lens Color

Parameters Symbol Max. Unit

Power Dissipation

Red

Yellow Green 60

Peak Forward Current

(a)

100 mA

DC Forward Current

(b)

Red

Yellow Green 25

Reverse Voltage V

5 V

Operating Temperature Range T

opr

-40℃

to +80℃

Storage Temperature Range T

stg

-40℃

to +85℃

Soldering Temperature T

sld

260

℃

for 5 Seconds

Notes:

a. Derate linearly as shown in derating curve.

b. Duty Factor = 10%, Frequency = 1 kHz.

RND 135-00199

Super Bright Red

White Diffused

Super Yellow Green

 Super Bright Red and Super Yellow Green chips are matched for uniform light output.

 Common Cathode.

 Long life solid state reliability.

 Low power consumption.

 I.C. compatible.

 Compliance with EU REACH.

 The product itself will remain within RoHS compliant Version.

Descriptions:

 The lamp is a three leads bicolor light sources designed for a variety of applications where dual state illumination is

required in the same package.There are two LED chips, high efficiency red, and high performance green (Yellow Green)

mounted on a central common cathode lead for maximum on axis viewability. Colors between Red and Green can be

generated by independently pulse width modulating the LED chips.

Applications:

Computer / Communication / Consumer / Home Appliance / Industrial

Absolute Maximum Ratings at Ta=25℃

Distrelec Schweiz AG, Grabenstrasse 6, 8606 Nänikon, Switzerland, T +41 44 944 99 11, info@distrelec.com, distrelec.com

Summary of content (7 pages)

PAGE 1
Bi-Colour LED, 5 mm Features  Super Bright Red and Super Yellow Green chips are matched for uniform light output.  Common Cathode.  Long life solid state reliability.  Low power consumption.  I.C. compatible.  Compliance with EU REACH.  The product itself will remain within RoHS compliant Version. Descriptions:  The lamp is a three leads bicolor light sources designed for a variety of applications where dual state illumination is required in the same package.
PAGE 2
Bi-Colour LED, 5 mm Electrical Optical Characteristics at Ta=25℃ Parameters Luminous Intensity (a) Viewing Angle (b) Symbol Iv 2θ1/2 Peak Emission Wavelength λp Dominant Wavelength (c) λd Spectral Line Half-Width △λ Forward Voltage VF Reverse Current IR Emitting Color Min. Typ. Max.
PAGE 3
Bi-Colour LED, 5 mm Package Dimensions (COM) 1 Green Anode 2 Common Cathode 3 Red Anode 1 3 Green Anode Common Cathode Red Anode POLARITY 1 2 3 Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ± 0.25 mm (.010″) unless otherwise noted. 3. Protruded resin under flange is 1.00mm (.039″) max. Distrelec Schweiz AG, Grabenstrasse 6, 8606 Nänikon, Switzerland, T +41 44 944 99 11, info@distrelec.com, distrelec.
PAGE 4
Bi-Colour LED, 5 mm Typical Electrical / Optical Characteristics Curves (25℃ Ambient Temperature Unless Otherwise Noted) Red: Forward Current & Forward Voltage Ta=25℃ Ta=25℃ Forward Current IF (mA) 100 75 50 25 0 300 1000 400 500 600 700 Wavelength λp (nm) Luminous Intensity & Ambient Temperature 100 10 1 -60 -40 -20 0 20 40 60 80 100 Ambient Temperature Ta (℃) 50 40 30 20 10 0 800 1.6 1.8 2.0 2.2 2.4 2.
PAGE 5
Bi-Colour LED, 5 mm Yellow Green: Forward Current & Forward Voltage Ta=25 ℃ Ta=25 ℃ Forward Current IF (mA) 100 75 50 25 0 300 1000 400 500 600 700 Wavelength λ p (nm) Luminous Intensity & Ambient Temperature 100 10 1 -60 -40 -20 0 20 40 60 80 100 A mbient Temperature Ta ( ℃ ) 50 40 30 20 10 0 800 1.6 1.8 2.0 2.2 2.4 2.
PAGE 6
Bi-Colour LED, 5 mm Cautions 1. Over-current-proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change (Burn out will happen). 2. Storage 2.1 The LEDs should be stored at 30°C or less and 70%RH or less after being shipped from RND and the storage life limits are 3 months. If the LEDs are stored for 3 months or more, they can be stored for a year in a sealed container with a nitrogen atmosphere and moisture absorbent material. 2.
PAGE 7
Bi-Colour LED, 5 mm (A) Recommended circuit (B) The brightness of each LED might appear different due to the differences in the I-V characteristics of those LEDs. 7. Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used. It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. 8.