User`s guide

User’s Guide HDSP System HDSP 9652 © RME
26
15.2 Tour de TotalMix
In the following chapters we will explain all functions of the surface step by step. Starting up
TotalMix, the last settings are recalled automatically. When executing the application for the
first time, a default file is loaded, sending all playback tracks 1:1 to the corresponding hardware
outputs with 0 dB gain. The faders in the upper row are set to maximum attenuation (called
m.a. in the following), so there is no monitoring of the input channels.
We will now create a small submix for the SPDIF output. Please start a multitrack playback and
connect a DA-converter to the SPDIF output. In playback channel 1 (labeled 'Out 1'), click onto
the routing window below the label. A list pops up, showing a checkmark in front of 'A1 1+2'.
Click onto 'SPDIF'. The list disappears, the routing window no longer shows 'A1 1+2', but
'SPDIF'. Now move the fader with the mouse. As soon as the fader value is unequal m.a., the
present state is being stored and routing is activated. Move the fader button to around 0 dB.
The present gain value is displayed below the fader in green letters.
In the lower row, on channels 25 and 26 (SP.L. and SP.R.), you
can also see the level of what you are hearing. The level meter of
the hardware output shows the outgoing level. Click into the area
above the fader and drag the mouse in order to set the
panorama, in this case the routing between channels 25 and 26.
The present pan value is also being displayed below the fader.
Please carry out the same steps for 'Out 2' now, in order to route
it to the analog output as well.
Often signals are stereo, i. e. a pair of two channels. It is
therefore helpful to be able to make the routing settings for two
channels at once. Press the Ctrl-key and click into the routing
window of 'Out 3' with the key pressed. The routing list pops up
with a checkmark at 'A1 3+4'. Click onto 'SPDIF'. Now, channel 4
has already been set to 'SPDIF' as well.
When you want to set the fader to exactly 0 dB, this can be
difficult, depending on the mouse configuration. Move the fader
close to the 0 position and now press the Shift-key. This activates
the fine-mode, which stretches the mouse movements by a factor
of 8. In this mode, a gain setting accurate to 0.1 dB is no problem
at all.
Please set 'Out 4' to a gain of around -20 dB and the pan close to
center. Now click onto the routing window. You'll now see two
checkmarks, one at 'A1 3+4', the other one at 'SPDIF'. Click onto
'A3 7+8'. The window disappears, fader and panpot jump to their
initial values, the signal can now be routed to the last ADAT
channels. You can continue, until all entries have got a
checkmark, i. e. you can send the signal to all outputs
simultaneously. This is one of several differences to the Cubase
mixer, which does not allow for multiple selections.
You will certainly have noticed that the mix has not changed, while you were routing the
channel to other outputs and setting different gain values. With all analogue and most digital
mixing desks, the fader setting would affect the level for every routed bus - not so for TotalMix.
TotalMix allows for setting all fader values individually. Therefore the faders and the panpots
jump to the appropriate setting as soon as another routing is chosen.
The checkmarks are un-checked by moving the fader to m.a. This setting deactivates the
routing...why route if there is no level? Click onto 'A1 3+4' in the routing window, pull the fader
down, open the routing window again - the checkmark is gone.