Instruction manual
7. MODBUS
IMS01J02-E1
159
Continued from the previous page.
Address CH Name Address CH Name
05DCH (1500) CH1 Input error determination Interval time setting
⋅
⋅
⋅
⋅
⋅
⋅
point (low) 06A7H (1703)
COM.PORT3 (for each
05EFH (1519) CH20
H-TIO-, H-CIO-A, H-SIO-A
control unit) H-PCP-J
05f0H (1520) CH1 Action at input error (high) PLC scanning time setting
⋅
⋅
⋅
⋅
⋅
⋅
06A8H (1704)
(for each control unit)
0603H (1539) CH20
H-TIO-, H-CIO-A, H-SIO-A
H-PCP-J
0604H (1540) CH1 Action at input error (low) Power supply frequency
⋅
⋅
⋅
⋅
⋅
⋅
06A9H (1705)
selection (for each
0617H (1559) CH20
H-TIO-, H-CIO-A, H-SIO-A
control unit) H-PCP-J
0618H (1560) CH1 AT bias H-PCP-J module DO
⋅
⋅
⋅
⋅
⋅
⋅
H-TIO-, H-CIO-A, H-SIO-A
06AAH (1706)
de-energized selection
062BH (1579) CH20 (for each control unit)
062CH (1580) CH1 ON/OFF control
H-PCP-J
⋅
⋅
⋅
⋅
⋅
⋅
differential gap (upper) Number of HBA trigger
063FH (1599) CH20
H-TIO-, H-CIO-A, H-SIO-A
06ABH (1707)
points (for each
0640H (1600) CH1 ON/OFF control control unit) H-CT-A
⋅
⋅
⋅
⋅
⋅
⋅
differential gap (lower) PV bias unit selection
0653H (1619) CH20
H-TIO-, H-CIO-A, H-SIO-A
06ACH (1708)
(for each control unit)
0654H (1620) CH1 Manipulated output value
H-TIO-, H-CIO-A, H-SIO-A
⋅
⋅
⋅
⋅
⋅
⋅
at input error Integral time limiter at AT
0667H (1639) CH20
H-TIO-, H-CIO-A, H-SIO-A
06ADH (1709)
end (for each control unit)
0668H (1640) CH1 Direct/Reverse action
H-TIO-, H-CIO-A, H-SIO-A
⋅
⋅
⋅
⋅
⋅
⋅
selection 06AEH (1710) Do not use this address
067BH (1659) CH20
H-TIO-, H-CIO-A, H-SIO-A
⋅
⋅
⋅
range
067CH (1660) CH1 Hot/Cold start selection 06B7H (1719)
⋅
⋅
⋅
⋅
⋅
⋅
H-TIO-, H-CIO-A, H-SIO-A
Alarm 1 differential
g
a
p
068FH (1679) CH20 06B8H (1720)
(for each control unit)
0690H (1680) CH1 Start determination point
H-TIO-, H-CIO-A, H-SIO-A
⋅
⋅
⋅
⋅
⋅
⋅
H-TIO-, H-CIO-A
Alarm 2 differential
g
a
p
06A3H (1699) CH20 06B9H (1721)
(for each control unit)
Control RUN/STOP
H-TIO-, H-CIO-A, H-SIO-A
06A4H (1700)
holding (for each control Alarm 1 type selection
unit) H-PCP-J 06BAH (1722)
(for each control unit)
Temperature rise
H-TIO-, H-CIO-A, H-SIO-A
06A5H (1701)
completion hold function Alarm 2 type selection
(for each control unit) 06BBH (1723)
(for each control unit)
H-PCP-J
H-TIO-, H-CIO-A, H-SIO-A
Interval time setting Alarm 1 hold action
06A6H (1702)
COM.PORT1/COM.PORT2
06BCH (1724)
(for each control unit)
(for each control unit)
H-TIO-, H-CIO-A, H-SIO-A
H-PCP-J
Continued on the next page.