Instruction manual

7. MODBUS
IMS01J02-E1
156
(2) Read/Write data
Address CH Name Address CH Name
00C8H ( 200) CH1 Temperature set value (SV) 01CCH ( 460) CH1 Heat-side proportioning
⋅
⋅
⋅
⋅
⋅
⋅
H-TIO-, H-CIO-A
⋅
⋅
⋅
⋅
⋅
⋅
cycle time
⋅
⋅
⋅
⋅
⋅
⋅
Motor speed set value
⋅
⋅
⋅
⋅
⋅
⋅
H-TIO-, H-CIO-A
00DBH ( 219) CH20
H-SIO-A
01DFH ( 479) CH20
00DCH ( 220) CH1 PID/AT transfer 01E0H ( 480) CH1 Cool-side proportioning
⋅
⋅
⋅
⋅
⋅
⋅
H-TIO-, H-CIO-A, H-SIO-A
⋅
⋅
⋅
⋅
⋅
⋅
cycle time
00EFH ( 239) CH20 01F3H ( 499) CH20
H-TIO-, H-CIO-A
00F0H ( 240) CH1 Heat-side proportional band 01F4H ( 500) CH1 Auto/Manual transfer
⋅
⋅
⋅
⋅
⋅
⋅
H-TIO-, H-CIO-A, H-SIO-A
⋅
⋅
⋅
⋅
⋅
⋅
H-TIO-, H-CIO-A
0103H ( 259) CH20 0207H ( 519) CH20
0104H ( 260) CH1 Cool-side proportional band 0208H ( 520) CH1 Manual output value
⋅
⋅
⋅
⋅
⋅
⋅
H-TIO-, H-CIO-A
⋅
⋅
⋅
⋅
⋅
⋅
H-TIO-, H-CIO-A
0117H ( 279) CH20 021BH ( 539) CH20
0118H ( 280) CH1 Integral time 021CH ( 540) CH1 LBA use selection
⋅
⋅
⋅
⋅
⋅
⋅
H-TIO-, H-CIO-A, H-SIO-A
⋅
⋅
⋅
⋅
⋅
⋅
H-TIO-, H-CIO-A
012BH ( 299) CH20 022FH ( 559) CH20
012CH ( 300) CH1 Derivative time 0230H ( 560) CH1 LBA time
⋅
⋅
⋅
⋅
⋅
⋅
H-TIO-, H-CIO-A, H-SIO-A
⋅
⋅
⋅
⋅
⋅
⋅
H-TIO-, H-CIO-A
013FH ( 319) CH20 0243H ( 579) CH20
0140H ( 320) CH1 Overlap/deadband 0244H ( 580) CH1 LBA deadband
⋅
⋅
⋅
⋅
⋅
⋅
H-TIO-, H-CIO-A
⋅
⋅
⋅
⋅
⋅
⋅
H-TIO-, H-CIO-A
0153H ( 339) CH20 0257H ( 599) CH20
0154H ( 340) CH1 Control response 0258H ( 600) CH1 PV bias
⋅
⋅
⋅
⋅
⋅
⋅
parameters
⋅
⋅
⋅
⋅
⋅
⋅
H-TIO-, H-CIO-A, H-SIO-A
0167H ( 359) CH20
H-TIO-, H-CIO-A, H-SIO-A
026BH ( 619) CH20
0168H ( 360) CH1 Alarm 1 set value 026CH ( 620) CH1 Temperature rise
⋅
⋅
⋅
⋅
⋅
⋅
H-TIO-, H-CIO-A, H-SIO-A
⋅
⋅
⋅
⋅
⋅
⋅
completion range
017BH ( 379) CH20 027FH ( 639) CH20
H-TIO-, H-CIO-A
017CH ( 380) CH1 Alarm 2 set value 0280H ( 640) CH1 Temperature rise
⋅
⋅
⋅
⋅
⋅
⋅
H-TIO-, H-CIO-A, H-SIO-A
⋅
⋅
⋅
⋅
⋅
⋅
completion trigger
018FH ( 399) CH20 0293H ( 659) CH20
H-TIO-, H-CIO-A
0190H ( 400) CH1 Heater break alarm 0294H ( 660) CH1 CT channel setting
⋅
⋅
⋅
⋅
⋅
⋅
set value 1
⋅
⋅
⋅
⋅
⋅
⋅
H-CT-A
01A3H ( 419) CH20
H-TIO-A/C/D
02A7H ( 679) CH20
01A4H ( 420) CH1 Heater break alarm 02A8H ( 680) Do not use this address
⋅
⋅
⋅
⋅
⋅
⋅
set value 2
⋅
⋅
⋅

range
01B7H ( 439) CH20
H-CT-A
02BBH ( 699)
01B8H ( 440) CH1 Operation mode transfer Control RUN/STOP
⋅
⋅
⋅
⋅
⋅
⋅
H-TIO-, H-CIO-A, H-SIO-A
02BCH ( 700)

transfer (for each control
01CBH ( 459) CH20 unit) H-PCP-J
Continued on the next page.