RKC Instrument Inc. Temperature Controller MODBUS SIO Driver 1 System Configuration....................................................................................................... 3 2 Selection of External Device ............................................................................................ 6 3 Example of Communication Setting ................................................................................. 7 4 Setup Items .......................................................
Temperature Controller MODBUS SIO Driver Introduction This manual describes how to connect the Display (GP3000 series) and the External Device (target Temperature Controller). In this manual, the connection procedure will be described by following the below sections: 1 System Configuration This section shows the types of External Devices which can be connected and SIO type.
Temperature Controller MODBUS SIO Driver 1 System Configuration The system configuration in the case when the External Device of RKC Instrument Inc. and the Display are connected is shown.
Temperature Controller MODBUS SIO Driver Link I/F SIO Type Setting Example Cable Diagram MA900-4--*-6/ Terminal block on the controller RS422/ 485(2 wire) Setting Example 8 (page 21) Cable Diagram 3 (page 62) MA900-4--*-7/ Terminal block on the controller RS422/ 485(4 wire) Setting Example 9 (page 23) Cable Diagram 7 (page 72) MA900-4--*-8/ Terminal block on the controller RS232C Setting Example 10 (page 25) Cable Diagram 6 (page 71) MA901-8--*
Temperature Controller MODBUS SIO Driver Link I/F SIO Type Setting Example Cable Diagram H-PCP-J-4-D* Connector on the controller RS422/ 485(4 wire) Setting Example 20 (page 45) Cable Diagram 4 (page 65) H-PCP-J-5-D* Connector on the controller RS422/ 485(2 wire) Setting Example 21 (page 48) Cable Diagram 5 (page 68) H-PCP-J-1-D* Connector on the controller RS232C Setting Example 18 (page 41) Cable Diagram 1 (page 58) H-PCP-J-4-D* Connector on the controller RS422/ 485(
Temperature Controller MODBUS SIO Driver 2 Selection of External Device Select the External Device to be connected to the Display. Setup Items Maker Driver Setup Description Select the maker of the External Device to be connected. Select "RKC Instrument Inc.". Select a model (series) of the External Device to be connected and connection method. Select "Temperature Controller MODBUS SIO". Check the External Device which can be connected in "Temperature Controller MODBUS SIO" in system configuration.
Temperature Controller MODBUS SIO Driver 3 Example of Communication Setting Examples of communication settings of the Display and the External Device, recommended by Digital Electronics Corp., are shown. 3.1 Setting Example 1 Settings of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in workspace.
Temperature Controller MODBUS SIO Driver Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings ] of [Device/PLC Settings ]. Settings of External Device Use the SET key, shift key, down key and up key on the front of the Temperature Controller for communication settings of the External Device. Please refer to the manual of the Temperature Controller for more details. Procedure 1.
Temperature Controller MODBUS SIO Driver 3.2 Setting Example 2 Settings of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in workspace.
Temperature Controller MODBUS SIO Driver Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings ] of [Device/PLC Settings ]. Settings of External Device Use the SET key, shift key, down key and up key on the front of the Temperature Controller for communication settings of the External Device. Please refer to the manual of the Temperature Controller for more details. Procedure 1.
Temperature Controller MODBUS SIO Driver 3.3 Setting Example 3 Settings of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in workspace.
Temperature Controller MODBUS SIO Driver Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings ] of [Device/PLC Settings ]. Settings of External Device Use the SET key, shift key, down key and up key on the front of the Temperature Controller for communication settings of the External Device. Please refer to the manual of the Temperature Controller for more details. Procedure 1.
Temperature Controller MODBUS SIO Driver 3.4 Setting Example 4 Settings of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in workspace.
Temperature Controller MODBUS SIO Driver Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings ] of [Device/PLC Settings ]. Settings of External Device Use the SET key, shift key, down key and up key on the front of the Temperature Controller for communication settings of the External Device. Please refer to the manual of the Temperature Controller for more details. Procedure 1.
Temperature Controller MODBUS SIO Driver 3.5 Setting Example 5 Settings of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in workspace.
Temperature Controller MODBUS SIO Driver Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings ] of [Device/PLC Settings ]. Settings of External Device Use the SET key, shift key, down key and up key on the front of the Temperature Controller for communication settings of the External Device. Please refer to the manual of the Temperature Controller for more details. Procedure 1.
Temperature Controller MODBUS SIO Driver 3.6 Setting Example 6 Settings of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in workspace.
Temperature Controller MODBUS SIO Driver Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings ] of [Device/PLC Settings ]. Settings of External Device Use the SET key, shift key, down key and up key on the front of the Temperature Controller for communication settings of the External Device. Please refer to the manual of the Temperature Controller for more details. Procedure 1.
Temperature Controller MODBUS SIO Driver 3.7 Setting Example 7 Settings of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in workspace.
Temperature Controller MODBUS SIO Driver Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings ] of [Device/PLC Settings ]. Settings of External Device Use the SET key, shift key, down key and up key on the front of the Temperature Controller for communication settings of the External Device. Please refer to the manual of the Temperature Controller for more details. Procedure 1.
Temperature Controller MODBUS SIO Driver 3.8 Setting Example 8 Settings of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in workspace.
Temperature Controller MODBUS SIO Driver Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings ] of [Device/PLC Settings ]. Settings of External Device Use the SET key, shift key, down key and up key on the front of the Temperature Controller for communication settings of the External Device. Please refer to the manual of the Temperature Controller for more details. Procedure 1.
Temperature Controller MODBUS SIO Driver 3.9 Setting Example 9 Settings of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in workspace.
Temperature Controller MODBUS SIO Driver Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings ] of [Device/PLC Settings ]. Settings of External Device Use the SET key, shift key, down key and up key on the front of the Temperature Controller for communication settings of the External Device. Please refer to the manual of the Temperature Controller for more details. Procedure 1.
Temperature Controller MODBUS SIO Driver 3.10 Setting Example 10 Settings of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in workspace.
Temperature Controller MODBUS SIO Driver Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings ] of [Device/PLC Settings ]. Settings of External Device Use the SET key, shift key, down key and up key on the front of the Temperature Controller for communication settings of the External Device. Please refer to the manual of the Temperature Controller for more details. Procedure 1.
Temperature Controller MODBUS SIO Driver 3.11 Setting Example 11 Settings of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in workspace.
Temperature Controller MODBUS SIO Driver Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings ] of [Device/PLC Settings ]. Settings of External Device Use the SET key, shift key, down key and up key on the front of the Temperature Controller for communication settings of the External Device. Please refer to the manual of the Temperature Controller for more details. Procedure 1.
Temperature Controller MODBUS SIO Driver 3.12 Setting Example 12 Settings of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in workspace.
Temperature Controller MODBUS SIO Driver Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings ] of [Device/PLC Settings ]. Settings of External Device Use the SET key, shift key, down key and up key on the front of the Temperature Controller for communication settings of the External Device. Please refer to the manual of the Temperature Controller for more details. Procedure 1.
Temperature Controller MODBUS SIO Driver 3.13 Setting Example 13 Settings of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in workspace.
Temperature Controller MODBUS SIO Driver Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings ] of [Device/PLC Settings ]. Settings of External Device Use the SET key, shift key, down key and up key on the front of the Temperature Controller for communication settings of the External Device. Please refer to the manual of the Temperature Controller for more details. Procedure 1.
Temperature Controller MODBUS SIO Driver 3.14 Setting Example 14 Settings of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in workspace.
Temperature Controller MODBUS SIO Driver Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings ] of [Device/PLC Settings ]. Settings of External Device Use the address setting switch on the front of the Temperature Controller and the DIP switch inside the Temperature Controller for communication settings of the External Device. Please refer to the manual of the Temperature Controller for more details. Procedure 1.
Temperature Controller MODBUS SIO Driver 3.15 Setting Example 15 Settings of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in workspace.
Temperature Controller MODBUS SIO Driver Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings ] of [Device/PLC Settings ]. Settings of External Device Use the address setting switch on the front of the Temperature Controller and the DIP switch inside the Temperature Controller for communication settings of the External Device. Please refer to the manual of the Temperature Controller for more details. Procedure 1.
Temperature Controller MODBUS SIO Driver 3.16 Setting Example 6 Settings of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in workspace.
Temperature Controller MODBUS SIO Driver Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings ] of [Device/PLC Settings ]. Settings of External Device Use the SET key, shift key, down key and up key on the front of the Temperature Controller for communication settings of the External Device. Please refer to the manual of the Temperature Controller for more details. Procedure 1.
Temperature Controller MODBUS SIO Driver 3.17 Setting Example 17 Settings of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in workspace.
Temperature Controller MODBUS SIO Driver Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings ] of [Device/PLC Settings ]. Settings of External Device Use the SET key, shift key, down key and up key on the front of the Temperature Controller for communication settings of the External Device. Please refer to the manual of the Temperature Controller for more details. Procedure 1.
Temperature Controller MODBUS SIO Driver 3.18 Setting Example 18 Settings of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in workspace.
Temperature Controller MODBUS SIO Driver Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings ] of [Device/PLC Settings ]. Settings of External Device Use the slave address setting switch on the front of the Temperature Controller and the DIP switch inside the Temperature Controller for communication settings of the External Device. Please refer to the manual of the Temperature Controller for more details. Procedure 1.
Temperature Controller MODBUS SIO Driver 3.19 Setting Example 19 Settings of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in workspace.
Temperature Controller MODBUS SIO Driver Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings ] of [Device/PLC Settings ]. Settings of External Device Use the slave address setting switch on the front of the Temperature Controller and the DIP switch inside the Temperature Controller for communication settings of the External Device. Please refer to the manual of the Temperature Controller for more details. Procedure 1.
Temperature Controller MODBUS SIO Driver 3.20 Setting Example 20 Settings of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in workspace.
Temperature Controller MODBUS SIO Driver Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings ] of [Device/PLC Settings ]. Settings of External Device Use the unit address setting switch on the front of the Temperature Controller and the DIP switch on the side of the Temperature Controller for communication settings of the External Device. Please refer to the manual of the Temperature Controller for more details.
Temperature Controller MODBUS SIO Driver COM.PORT3 setting switch SW3 Settings 1 OFF 2 OFF Description Data bit configuration 3 OFF 4 OFF 5 ON 6 OFF Initialization 7 OFF MODBUS mode selection 8 OFF Fixed Speed Communication Protocol • Parameters to be set vary depending on the Temperature Controller. Please refer to the manual of the Temperature Controller for more details.
Temperature Controller MODBUS SIO Driver 3.21 Setting Example 21 Settings of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in workspace.
Temperature Controller MODBUS SIO Driver Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings ] of [Device/PLC Settings ]. Settings of External Device Use the unit address setting switch in front of the Temperature Controller and the DIP switch on the side of the Temperature Controller for communication settings of the External Device. Please refer to the manual of the Temperature Controller for more details.
Temperature Controller MODBUS SIO Driver • COM.PORT3 setting switch SW3 Settings 1 OFF 2 OFF Description Data bit configuration 3 OFF 4 OFF 5 ON 6 OFF Initialization 7 OFF MODBUS mode selection 8 OFF Fixed Speed Communication Protocol • Parameters to be set vary depending on the Temperature Controller. Please refer to the manual of the Temperature Controller for more details.
Temperature Controller MODBUS SIO Driver 3.22 Setting Example 22 Settings of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in workspace.
Temperature Controller MODBUS SIO Driver Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings ] of [Device/PLC Settings ]. Settings of External Device Use the unit address setting switch in front of the Temperature Controller and the DIP switch on the side of the Temperature Controller for communication settings of the External Device. Please refer to the manual of the Temperature Controller for more details.
Temperature Controller MODBUS SIO Driver 4 Setup Items Set communication settings of the Display with GP-Pro Ex or in off-line mode of the Display. The setting of each parameter must be identical to that of External Device. )"3 Example of Communication Setting" (page 7) 4.1 Setup Items in GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in workspace.
Temperature Controller MODBUS SIO Driver Setup Items Setup Description Wait To Send Use an integer from 0 to 255 to enter standby time (ms) for the Display from receiving packets to transmitting next commands. RI/VCC Switches RI/VCC of the 9th pin. Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings ] of [Device/PLC Settings ].
Temperature Controller MODBUS SIO Driver 4.2 Setup Items in Off-Line Mode • Please refer to GP3000 Series User's Manual for more information on how to enter off-line mode or about operation. Cf. GP3000 Series User's Manual "Chapter 4 Setting" Communication Settings To display the setting screen, touch [Device/PLC Settings] from [Peripheral Equipment Settings] in the off-line mode. Touch the External Device you want to set from the displayed list.
Temperature Controller MODBUS SIO Driver Device Setting To display the setting screen, touch [Device/PLC Settings] from [Peripheral Equipment Settings]. Touch the External Device you want to set from the displayed list, and touch [Device Settings]. Setup Items Setup Description Device name Select the External Device to set. Device name is a title of the External Device set with GPPro EX.(Default [PLC1]) Series Displays a model of the External Device.
Temperature Controller MODBUS SIO Driver Option To display the setting screen, touch [Device/PLC Settings] from [Peripheral Settings]. Touch the External Device you want to set from the displayed list, and touch [Option]. Setup Items RI/VCC Setup Description Switches RI/VCC of the 9th pin.
Temperature Controller MODBUS SIO Driver 5 Cable Diagram The cable diagram shown below may be different from the cable diagram recommended by RKC Instrument Inc. Please be assured there is no operational problem in applying the cable diagram shown in this manual. • The FG pin of the main body of the External Device must be D-class grounded. Please refer to the manual of • SG and FG are connected inside the Display.
Temperature Controller MODBUS SIO Driver Cable Diagram 2 Display (Connection Port) GP(COM1)*1 AGP-3302(COM2) Cable A COM port conversion adapter by Digital Electronics Corp. CA3-ADPCOM-01 + Connector terminal block conversion adapter by Digital Electronics Corp. CA3-ADPTRM-01 + Your own cable B Your own cable C Online adapter by Digital Electronics Corp. CA4-ADPONL-01 + Connector terminal block conversion adapter by Digital Electronics Corp.
Temperature Controller MODBUS SIO Driver • Display 1: n connection Termination resistance 120Ω + 10% or less CA3-ADPCOM-01 CA3-ADPTRM-01 Termination resistance 120Ω + 10% or less External Device COM.PORT2 COM.PORT1 Modular 6 Pin Modular 6 Pin Shield Signal name Shield External Device COM.PORT2 COM.
Temperature Controller MODBUS SIO Driver • Display 1:n Connection Termination resistance 120Ω + 10% or less CA4-ADPONL-01 CA3-ADPTRM-01 Termination resistance 120Ω + 10% or less Shield Signal name External Device COM.PORT2 COM.PORT1 Modular 6 Pin Modular 6 Pin Pin Pin Signal name Signal name RDA 4 RDB SDA External Device COM.PORT1 COM.
Temperature Controller MODBUS SIO Driver Cable Diagram 3 Display (Connection Port) Cable GP(COM1)*1 AGP-3302(COM2) A COM port conversion adapter by Digital Electronics Corp. CA3-ADPCOM-01 + Connector terminal block conversion adapter by Digital Electronics Corp. CA3-ADPTRM-01 + Your own cable B Your own cable C Online adapter by Digital Electronics Corp. CA4-ADPONL-01 + Connector terminal block conversion adapter by Digital Electronics Corp.
Temperature Controller MODBUS SIO Driver B) When using your own cable • 1:1 Connection D-Sub 9 Pin (socket) Termination resistance 120 Ω (1/2W) Display Pin Signal name 1 RDA External Device Terminal block 2 RDB Signal name 3 SDA T/R(B) 7 SDB T/R(A) 5 SG SG 4 ERA 8 CSA 9 ERB 6 CSB Termination resistance 120 Ω (1/2W) FG Shell • Shield 1:n Connection Termination resistance 120 Ω (1/2W) Display D-Sub 9 Pin (socket) Pin Signal name 1 RDA External Device Terminal block 2
Temperature Controller MODBUS SIO Driver D) When using the online adapter (CA4-ADPONL-01) by Digital Electronics Corp.
Temperature Controller MODBUS SIO Driver Cable Diagram 4 Display (Connection Port) Cable GP(COM1)*1 AGP-3302(COM2) A COM port conversion adapter by Digital Electronics Corp. CA3-ADPCOM-01 + Connector terminal block conversion adapter by Digital Electronics Corp. CA3-ADPTRM-01 + Your own cable B Your own cable C Online adapter by Digital Electronics Corp. CA4-ADPONL-01 + Connector terminal block conversion adapter by Digital Electronics Corp.
Temperature Controller MODBUS SIO Driver B) When using your own cable • 1:1 Connection D-Sub 9 Pin (socket) Display Pin Signal name Pin Signal name 1 RDA 4 T(B) 2 RDB 5 T(A) 3 SDA 2 R(B) 7 SDB 1 R(A) 5 SG 3 SG 4 ERA 6 Shield 8 CSA 9 ERB 6 CSB Shell • Shield External Device COM.PORT1 Modular 6 Pin FG 1:n Connection Shield D-Sub 9 Pin (socket) Display External Device COM.PORT2 COM.
Temperature Controller MODBUS SIO Driver • 1:n Connection External Device COM.PORT2 COM.PORT1 Modular 6 Pin Modular 6 Pin Pin Signal name Pin Signal name Shield Signal name Display CA4-ADPONL-01 CA3-ADPTRM-01 External Device COM.PORT2 COM.
Temperature Controller MODBUS SIO Driver Cable Diagram 5 Display (Connection Port) Cable GP(COM1)*1 AGP-3302(COM2) A COM port conversion adapter by Digital Electronics Corp. CA3-ADPCOM-01 + Connector terminal block conversion adapter by Digital Electronics Corp. CA3-ADPTRM-01 + Your own cable B Your own cable C Online adapter by Digital Electronics Corp. CA4-ADPONL-01 + Connector terminal block conversion adapter by Digital Electronics Corp.
Temperature Controller MODBUS SIO Driver B) When using your own cable • 1:1 Connection D-Sub 9 Pin (socket) Pin Signal name 1 RDA External Device COM.PORT1 Modular 6 Pin 2 RDB Pin Signal name 3 SDA 2 T/R(B) 7 SDB 1 T/R(A) 5 SG 3 SG 4 ERA 6 Shield 8 CSA 9 ERB 6 CSB Display FG Shell • Shield 1:n Connection D-Sub 9 Pin (socket) Display Pin Signal name 1 RDA 2 RDB External Device COM.PORT2 COM.
Temperature Controller MODBUS SIO Driver D) When using the online adapter (CA4-ADPONL-01) by Digital Electronics Corp. and your own cable • 1:1 Connection D-Sub 9 Pin (plug) CA4-ADPONL-01 Display Pin Signal name 1 TERMRX 2 RDA 7 RDB 3 SDA 2 T/R(B) 8 SDB 1 T/R(A) 5 SG 3 SG 9 TERMTX 6 Shield Shell FG Shield External Device COM.PORT1 Modular 6 Pin Pin Signal name Your own cable • 1:n Connection D-Sub 9 Pin (plug) Pin CA4-ADPONL-01 Display Signal name External Device COM.
Temperature Controller MODBUS SIO Driver Cable Diagram 6 Display (Connection Port) GP(COM1) Cable Remarks Your own cable Cable length: 10m or less When using your own cable D-Sub 9 Pin (socket) Shield External Device Terminal block Pin Signal name Signal name 2 RD(RXD) SD 3 SD(TXD) RD 5 SG SG 4 ER(DTR) 6 DR(DSR) Display 7 RS(RTS) 8 CS(CTS) Shell FG GP-Pro EX Device/PLC Connection Manual 71
Temperature Controller MODBUS SIO Driver Cable Diagram 7 Display (Connection Port) Cable GP(COM1)*1 AGP-3302(COM2) A COM port conversion adapter by Digital Electronics Corp. CA3-ADPCOM-01 + Connector terminal block conversion adapter by Digital Electronics Corp. CA3-ADPTRM-01 + Your own cable B Your own cable C Online adapter by Digital Electronics Corp. CA4-ADPONL-01 + Connector terminal block conversion adapter by Digital Electronics Corp.
Temperature Controller MODBUS SIO Driver B) When using your own cable • 1:1 Connection Shield Termination D-Sub 9 Pin (socket) resistance Pin Signal name 120 Ω (1/2W) Display 1 RDA Termination resistance 120 Ω (1/2W) Signal name Termination resistance 120 Ω (1/2W) Termination resistance 120 Ω (1/2W) T(B) 2 RDB T(A) 3 SDA R(B) 7 SDB R(A) 5 SG SG 4 ERA 8 CSA 9 ERB 6 CSB Shell • External Device Terminal block FG 1:n Connection Termination D-Sub 9 Pin (socket) resistance Pin Signal
Temperature Controller MODBUS SIO Driver D) When using the online adapter (CA4-ADPONL-01) by Digital Electronics Corp.
Temperature Controller MODBUS SIO Driver Cable Diagram 8 Display (Connection Port) Cable GP(COM1)*1 AGP-3302(COM2) A COM port conversion adapter by Digital Electronics Corp. CA3-ADPCOM-01 + Connector terminal block conversion adapter by Digital Electronics Corp. CA3-ADPTRM-01 + Your own cable B Your own cable C Online adapter by Digital Electronics Corp. CA4-ADPONL-01 + Connector terminal block conversion adapter by Digital Electronics Corp.
Temperature Controller MODBUS SIO Driver • 1: n connection Broadcast terminal Shield Display CA3-ADPCOM-01 CA3-ADPTRM-01 Shield Broadcast terminal Signal name Signal name Signal name RDA T(B) T(B) RDB T(A) T(A) SDA R(B) R(B) SDB R(A) R(A) SG SG SG FG Shield Shield W-BF-01 by RKC W-BF-01 by RKC COM.PORT3 Modular 6 Pin COM.PORT3 Modular 6 Pin Temperature controller Temperature controller Your own cable • Termination resistance is not necessary.
Temperature Controller MODBUS SIO Driver C) When using the online adapter (CA4-ADPONL-01), the connector terminal block conversion adapter (CA3ADPTRM-01) by Digital Electronics Corp. • 1:1 Connection External Device COM.
Temperature Controller MODBUS SIO Driver • 1:n Connection D-Sub 9 Pin (plug) Pin CA4-ADPONL-01 Display Signal name Broadcast terminal Shield Shield Broadcast terminal 1 TERMRX Signal name Signal name 2 RDA T(B) T(B) 7 RDB T(A) T(A) 3 SDA R(B) R(B) 8 SDB R(A) R(A) 5 SG SG SG 9 TERMTX Shield Shield Shell FG W-BF-01 by RKC COM.PORT3 Modular 6 Pin Temperature controller Your own cable • Termination resistance is not necessary.
Temperature Controller MODBUS SIO Driver Cable Diagram 9 Display (Connection Port) Cable GP(COM1)*1 AGP-3302(COM2) A COM port conversion adapter by Digital Electronics Corp. CA3-ADPCOM-01 + Connector terminal block conversion adapter by Digital Electronics Corp. CA3-ADPTRM-01 + Your own cable B Your own cable C Online adapter by Digital Electronics Corp. CA4-ADPONL-01 + Connector terminal block conversion adapter by Digital Electronics Corp.
Temperature Controller MODBUS SIO Driver • 1: n connection Shield Signal name Display CA3-ADPCOM-01 CA3-ADPTRM-01 RDA Broadcast terminal RDB Signal name Signal name SDA T/R(B) T/R(B) SDB T/R(A) T/R(A) SG SG SG FG Shield Shield Shield Broadcast terminal W-BF-01 by RKC W-BF-01 by RKC COM.PORT3 Modular 6 Pin COM.PORT3 Modular 6 Pin Temperature controller Temperature controller Your own cable • Termination resistance is not necessary.
Temperature Controller MODBUS SIO Driver C) When using the online adapter (CA4-ADPONL-01), the connector terminal block conversion adapter (CA3ADPTRM-01) by Digital Electronics Corp. • 1:1 Connection Signal name Shield RDA Display CA4-ADPONL-01 CA3-ADPTRM-01 External Device COM.
Temperature Controller MODBUS SIO Driver • 1:n Connection D-Sub 9 Pin (plug) Pin CA4-ADPONL-01 Display Signal name 1 TERMRX 2 RDA Broadcast terminal 7 RDB Signal name Signal name 3 SDA T/R(B) T/R(B) 8 SDB T/R(A) T/R(A) 5 SG SG SG 9 TERMTX Shield Shield Shell FG Shield W-BF-01 by RKC GP-Pro EX Device/PLC Connection Manual 82 Broadcast terminal W-BF-01 by RKC COM.PORT3 Modular 6 Pin COM.
Temperature Controller MODBUS SIO Driver 6 Supported Device Range of supported device address is shown in the table below. Please note that the actually supported range of the devices varies depending on the External Device to be used. Please check the actual range in the manual of your External Device. 6.1 CB Series This address can be specified as system data area. Device Holding Register *1 Bit Address Word Address 0000.0-001C.
Temperature Controller MODBUS SIO Driver • To set [Enable System Data Area] in the system area setting of GP-Pro EX may cause malfunction. Do not set [Enable System Data Area]. • You can set only Read Area Size for the system data area available to use in the Temperature Controller. Please refer to the GP-Pro EX Reference Manual for reading area size. Cf. GP-Pro EX Reference Manual "Appendix 1.
Temperature Controller MODBUS SIO Driver 6.4 MA900/901 Series This address can be specified as system data area. Device Holding Register *1 Bit Address Word Address 0000.0-14A0.F 0000-14A0 32 bits Remarks *1 When you write the bit address, the Display reads the word address corresponding to that of the External Device first. Then, it changes the target bit address among the word data once read and returns the word data to the External Device.
Temperature Controller MODBUS SIO Driver • You can set only Read Area Size for the system data area available to use in the Temperature Controller. Please refer to the GP-Pro EX Reference Manual for reading area size. Cf. GP-Pro EX Reference Manual "Appendix 1.4 LS Area (only for direct access method)" • Please refer to the precautions on manual notation for icons in the table. ) "Manual Symbols and Terminology" • Even if you use the nonexistent address, read error may not be displayed.
Temperature Controller MODBUS SIO Driver 6.7 SA100 Series This address can be specified as system data area. Device Holding Register *1 Bit Address Word Address 0000.0-0021.F 0000-0021 32 bits Remarks *1 When you write the bit address, the Display reads the word address corresponding to that of the External Device first. Then, it changes the target bit address among the word data once read and returns the word data to the External Device.
Temperature Controller MODBUS SIO Driver • You can set only Read Area Size for the system data area available to use in the Temperature Controller. Please refer to the GP-Pro EX Reference Manual for reading area size. Cf. GP-Pro EX Reference Manual "Appendix 1.4 LS Area (only for direct access method)" • Please refer to the precautions on manual notation for icons in the table. ) "Manual Symbols and Terminology" • Even if you use the nonexistent address, read error may not be displayed.
Temperature Controller MODBUS SIO Driver 6.10 SR Mini HG(H-PCP-J) Series This address can be specified as system data area. Device Holding Register *1 Bit Address Word Address 0000.0-1DEE.F 0000-1DEE 32 bits Remarks *1 When you write the bit address, the Display reads the word address corresponding to that of the External Device first. Then, it changes the target bit address among the word data once read and returns the word data to the External Device.
Temperature Controller MODBUS SIO Driver 7 Device Code and Address Code Use device code and address code when you select "Device Type & Address" for the address type in data displays. 7.
Temperature Controller MODBUS SIO Driver 7.8 SA200 Series Device Device Name Device Code (HEX) - 0080 Device Name Device Code (HEX) - 0080 Device Name Device Code (HEX) - 0080 Holding Register 7.9 Same as Word Address SR Mini Series Device Holding Register 7.
Temperature Controller MODBUS SIO Driver 8 Error Messages Error messages are displayed on the screen of the Display as follows: "No.:Device Name:Error Message(Error Occurrence Area)". Each description is shown below. Item Description No. Error No. Device Name Name of the External Device where error occurs. Device name is a title of the External Device set with GP-Pro EX.(Initial value[PLC1]) Error Message Displays messages related to the error which occurs.
