Operator`s manual
Table Of Contents
- RS 8000/8600 Getting Started Guide
- Notices
- Table of Contents
- 1 About This Guide
- 2 Introduction
- 3 Hardware Installation
- 3.1 Safety Considerations
- 3.2 Hardware Specifications
- 3.3 Installing the Hardware
- 3.3.1 Verifying Your Shipment
- 3.3.2 Installing the Chassis
- 3.3.3 Installing an AC Power Supply
- 3.3.4 Installing a DC Power Supply
- 3.3.5 Installing the Control Module
- 3.3.6 Installing the Switching Fabric Module (RS8600 only)
- 3.3.7 Installing Line Cards
- 3.3.8 Installing GBIC Modules into Line Cards
- 3.3.9 Installing ATM Physical Media Cards (PHYs)
- 3.3.10 Multi-rate WAN Line Card and WICs
- 3.3.11 SRP Line Cards and Bridge Mate Module
- 3.3.12 Installing SFP Transceivers
- 3.3.13 Attaching the Network Cables to Line Cards
- 4 Initial Configuration
- 4.1 Powering on the RS8000/8600
- 4.2 Starting the Command Line Interface
- 4.3 Configuration Changes and Saving the Configuration File
- 4.4 Setting the Basic System Information
- 4.5 Setting Up Passwords
- 4.6 Setting Up SNMP
- 4.7 Setting the DNS Domain Name and Address
- 4.8 Setting the SYSLOG Parameters
- 4.9 Using Redundant Control Modules
- 5 Managing Software
- Appendix A Troubleshooting
- Appendix B International SaFety Information
- Index
2-50 Riverstone Networks RS 8000/8600 Switch Router Getting Started Guide
Hardware Overview Introduction
The following table maps the pin assignments for Riverstone’s 50-pin HSSI connector for the Dual HSSI line card.
Note
Because neither connector at the ends of the SYS-HSSI-CAB cable is keyed, you
can simply plug either end of the cable into either your Dual HSSI line card or the
remote HSSI CSU/DSU data port.
Table 2-36 shows the pin positions in the 50-pin HSSI connector.
Table 2-46 Connector specifications for dual HSSI line card
Port Type Specification
HSSI
•
HSSI rev 2.11
•
50-pin High Speed Serial Interface (HSSI) connector; see
Table 2-47 for pin assignments
•
Recommended 3 meters (10 feet) segment length for standard
WAN line card-to-CSU/DSU data port.
Table 2-47 Pin assignments for dual HSSI line card
Pin Signal Pin Signal Pin Signal Pin Signal
1 GND 14 (reserved) 26 GND 39 (reserved)
2 RT+ 15 (reserved) 27 RT- 40 (reserved)
3 CA+ 16 (reserved) 28 CA- 41 (reserved)
4 RD+ 17 (reserved) 29 RD- 42 (reserved)
5 LC+ 18 (reserved) 30 LC- 43 (reserved)
6 ST+ 19 GND 31 ST- 44 GND
7 GND 20 (reserved) 32 GND 45 (reserved)
8 TA+ 24 (reserved) 33 TA- 46 (reserved)
9 TT+ 22 (reserved) 34 TT- 47 (reserved)
10 LA+ 23 (reserved) 35 LA- 48 (reserved)
11 SD+ 24 (reserved) 36 SD- 49 (reserved)
12 LB+ 25 GND 37 LB- 50 GND
13 GND 38 GND