Operator`s manual
Table Of Contents
- RS 8000/8600 Getting Started Guide
- Notices
- Table of Contents
- 1 About This Guide
- 2 Introduction
- 3 Hardware Installation
- 3.1 Safety Considerations
- 3.2 Hardware Specifications
- 3.3 Installing the Hardware
- 3.3.1 Verifying Your Shipment
- 3.3.2 Installing the Chassis
- 3.3.3 Installing an AC Power Supply
- 3.3.4 Installing a DC Power Supply
- 3.3.5 Installing the Control Module
- 3.3.6 Installing the Switching Fabric Module (RS8600 only)
- 3.3.7 Installing Line Cards
- 3.3.8 Installing GBIC Modules into Line Cards
- 3.3.9 Installing ATM Physical Media Cards (PHYs)
- 3.3.10 Multi-rate WAN Line Card and WICs
- 3.3.11 SRP Line Cards and Bridge Mate Module
- 3.3.12 Installing SFP Transceivers
- 3.3.13 Attaching the Network Cables to Line Cards
- 4 Initial Configuration
- 4.1 Powering on the RS8000/8600
- 4.2 Starting the Command Line Interface
- 4.3 Configuration Changes and Saving the Configuration File
- 4.4 Setting the Basic System Information
- 4.5 Setting Up Passwords
- 4.6 Setting Up SNMP
- 4.7 Setting the DNS Domain Name and Address
- 4.8 Setting the SYSLOG Parameters
- 4.9 Using Redundant Control Modules
- 5 Managing Software
- Appendix A Troubleshooting
- Appendix B International SaFety Information
- Index
2-44 Riverstone Networks RS 8000/8600 Switch Router Getting Started Guide
Hardware Overview Introduction
POS OC-12c MMF Line Card and POS OC-12c SMF Line Card
The Packet-over-SONET line card supports two OC-12c connections. One model of the POS line card is designed to
work with single-mode fiber (SMF), the other POS line card uses multi-mode fiber (MMF). Each line card uses
SC-type connectors. Figure 2-29 shows the front panel of the POS OC-12c MMF line card.
Figure 2-29 Front panel of POS OC-12c MMF line card
Figure 2-30 shows the front panel of the POS OC-12c SMF line card.
Figure 2-30 Front panel of POS OC-12c SMF line card
The following table lists the media specifications for the POS OC-12c MMF and POS OC-12c SMF line cards.
Table 2-38 Connector specifications for POS OC-12c line card
Port type Specification
POS OC-12c
•
Bellcore GR253, ITU -T G.957, ITU-T G.958
•
PPP over SONET/SDH (RFC 1619), PPP in HDLC
framing (RFC 1662)
•
SC-style Media Interface Connector (MIC); either
connection pin in the MIC can be used for transmit or
receive.
•
62.5 micron or 50 micron multi-mode fiber-optic cable
•
9.5 micron single-mode fiber-optic cable
•
Maximum 1 kilometers for multi-mode fiber-optic cable
•
Maximum 13 kilometers for single-mode fiber-optic cable
21
Link
Offline
Online
Tx
Rx
POS OC-12c MMFG8M-P12B1-02
Hot
Swap
Link
Tx
Rx
21
Link
Offline
Online
Tx
Rx
POS OC-12c SMFG8M-P12B9-02
Hot
Swap
Link
Tx
Rx