Technical data

Page 10/ 24 34-81 10/2013
5. PARAMETERS
All the parameters can be set in:
- Pr1: immediately accessible menu.
- Pr2: password protected menu.
Label: The displayed label when using the Keypad.
Range: Indicates the possible values and units that can be set.
Firm Version: Firmware of the TempTrac control can be viewed in the rEL parameter.
Label
Firm
Version Description
Range
X÷YFromXtoY
Rev 0.3
Level
Rev 0.5
Level
Hex
Modbus
Address
Base 0
Modbus
Command
Address
40000+



St1
0.3 & 0.5
Setpoint1 LS1÷US1
Pr1 Pr1
0x300 769
St2
0.3 & 0.5
Setpoint2 LS2÷US2
Pr1 Pr1
0x301 770
St3
0.3 & 0.5
Setpoint3 LS3÷US3
Pr1 Pr1
0x302 771
St5
0.3 & 0.5
Setpoint5Setpoint3alternate‐20÷70°F
Pr1 Pr1
0x303 772
HY1
0.3 & 0.5
DifferentialforSt1‐22÷22°F
Pr2 Pr2
0x304 773
LS1
0.3 & 0.5
Minimumsetpoint1‐40°F÷SET
Pr2 Pr2
0x305 774
US1
0.3 & 0.5
Maximumsetpoint1 SET÷230°F
Pr2 Pr2
0x306 775
AC1
0.3 & 0.5
Anti‐shortcycledelayforoutput1 0÷30min.
Pr2 Pr2
0x307 776
S2c
0.3 & 0.5
ConfigurationofSt2:dependentonSt1orindependent diP;ind
Pr3 Pr2
0x308 777
HY2
0.3 & 0.5
DifferentialforSt2‐22÷22°F
Pr2 Pr2
0x309 778
LS2
0.3 & 0.5
Minimumsetpoint2‐40°F÷St2
Pr2 Pr2
0x30A 779
uS2
0.3 & 0.5
Maximumsetpoint2 St2÷230°F
Pr2 Pr2
0x30B 780
AC2
0.3 & 0.5
Anti‐shortcycledelayforoutput2 0÷30min.
Pr2 Pr2
0x30C 781
S3c
0.3 & 0.5
ConfigurationofSt3:dependentonSt1orindependent diP;ind
Pr2 Pr2
0x30D 782
HY3
0.3 & 0.5
Differentialforsetpoint3St3‐22÷22°F
Pr2 Pr2
0x30E 783
LS3
0.3 & 0.5
Minimumsetpoint3St3‐40°F÷St3
Pr2 Pr2
0x30F 784
uS3
0.3 & 0.5
Maximumsetpoint3St3 St3÷230°F
Pr2 Pr2
0x310 785
AC3
0.3 & 0.5
Anti‐shortcycledelayforoutput3 0÷30min.
Pr2 Pr2
0x311 786
o3P
0.3 & 0.5
Probeselectionforoutput3 Pb1/Pb2
Pr2 Pr2
0x312 787
SSE
0.3 & 0.5
Setpointshiftforoutput3enabledisable No;Yes
Pr2 Pr2
0x313 788
HY5
0.3 & 0.5
Differentialforsetpoint5‐22÷22°F
Pr2 Pr2
0x314 789
Ac5
0.3 & 0.5
Anti‐shortcycledelayforoutput3alternatesetpoint 0÷30min.
Pr2 Pr2
0x315 790
AcA
0.3 & 0.5
TimedelaybetweentheSt3toSt5setpointshift 0÷15min.
Pr2 Pr2
0x316 791
ANALOGUE OUTPUT 4÷20mA (output 4)
 
 
S4c
0.3 & 0.5
ConfigurationofSt4:dependentonSt1orindependent diP;ind
Pr3 Pr2
0x317 792
St4
0.3 & 0.5
Analogueoutputsetpoint ‐100÷100°F
Pr2 Pr2
0x318 793
SR
0.3 & 0.5
Analogueoutputbandwidth‐100÷100°F
Pr2 Pr2
0x319 794
Th4
0.3 & 0.5
Outlet temperature threshold for forcing to 4ma the
analog output
‐40°F÷230°F
Pr2 Pr2
0x31A 795
HY4
0.3 & 0.5
Differentialforrestartworkingofanalogoutput‐45÷‐1°F
Pr2 Pr2
0x31B 796
Ac4
0.3 & 0.5
Anti‐shortcycledelayforoutput4 0÷30min.
Pr2 Pr2
0x31C 797
PS4
0.3 & 0.5
Analogoutputpercentage(nu=101) 0÷100,nu
Pr2 Pr2
0x31D 798
PP4
0.3 & 0.5
Analogoutputpercentagewithfaultprobe1(nu=101) 0÷100,nu
Pr3 Pr2
0x31E 799
DYNAMIC RESET
 
 
tt
0.3 & 0.5
OutdoortemperaturethresholdfordynamicresetofSt1 ‐40÷230°F
Pr2 Pr2
0x31F 800
rr2
0.3 & 0.5
Outdoortemperaturebandwidth‐100÷100°F
Pr2 Pr2
0x320 801
rr1
0.3 & 0.5
MaximumshiftofSt1‐100÷100°F
Pr2 Pr2
0x321 802
tt2
0.3 & 0.5
Outdoortemperaturethresholdtoopenalltheloads ‐40÷230°F
Pr2 Pr2
0x322 803