ASSEMBLY INSTRUCTIONS RiverRidge® Madison Single Door Floor Cabinet ITEM#: 06-111 ITEM#: 06-122 White Gray ADULT ASSEMBLY REQUIRED This product requires assembly by an adult because of small parts. Care should be taken in unpacking and assembling this item to keep small parts away from children. During assembly children should be kept away from the product due to possible risk of injury. WARNING SEE FULL WARNING ON PAGE 2 Young children can be seriously injured or killed if furniture tips over.
THIS SHELF UNIT WILL HOLD UP TO 20 POUNDS PER SHELF OR TOP BOARD FOR A TOTAL OF 80 POUNDS. DO NOT LOAD EACH SHELF WITH MORE THAN 20 POUNDS OR 80 POUNDS TOTAL WEIGHT. IF OVERLOADED WITH MORE THAN 20 POUNDS PER SHELF OR 80 POUNDS TOTAL WEIGHT, SHELF MAY TIP FROM THE WALL AND CAUSE SERIOUS INJURY OR DEATH.
PARTS LIST NO QTY DESCRIPTION 1 1PC Top Board 2 1PC Bottom Board 3 1PC Left Side Panel 4 1PC Right Side Panel 5 1PC Cross Bar 6 1PC Shelf 7 1PC Adjustable Shelf 8 1PC Door 9 1PC Back Board
PARTS LIST NO PARTS QTY DESCRIPTION A 12PCS Cam Bolt B 12PCS Cam Lock C 12PCS Wood Dowel D 4PCS Shelf Holder E 2PCS Hinge F 1PCS Handle G 12PCS Screw (4x12mm) H 1PC Screw (4x10mm) I 1PC Adjustable Anchor Bracket J 12PCS Screw (2.5x10mm) K 1PC Plastic Anchor L 1PC Screw (4x30mm) M 1PC Silicon pad N 2PCS Screw (3.
STEP 1 1. Screw 4 cam bolts (A) into cam bolt holes on top board (1). 2. Attach bracket (I) to shelf (6) by inserting 1 screw (H) through hole on bracket (I), then tighten to shelf (6). STEP 2 1. Screw 4 cam bolts (A) into cam bolt holes on left side panel (3). 2. Screw 4 cam bolts (A) into cam bolt holes on right side panel (4). STEP 3 1. Insert 6 wood dowels (C) into wood dowel holes on left side panel (3). 2.
STEP 4 1. Attach top board (1) to left side panel (3) and right side panel (4) by inserting cam bolts into cam lock holes on left side panel (3) and right side panel (4). 2. Insert 4 cam locks (B) into cam lock holes on left side panel (3) and right side panel (4), then rotate clockwise to secure cam bolts in place. STEP 5 1. Attach back board (9) to cabinet by inserting 12 screws (J) through holes on back board (9), then tighten to cabinet.
STEP 6 1. Attach 2 hinges (E) to door (8) by inserting 4 screws (G) through holes on hinges, then tighten to door (8). 2. Attach handle (F) to door (8) by inserting 2 screws (N) through holes on handle (F), then tighten to door (8). 3. Stick 1 silicon pad (M) on handle (F) to prevent scratches on shelf edge when door is closed. STEP 7 Door Adjustments 1. Attach door (8) to cabinet by inserting 8 screws (G) through holes on hinges, then tighten to right side panel (4). 2.
STEP 8 Option #1: Securing to Drywall 1. Position cabinet against wall in desired location. Using a pencil, make small mark on wall through hole on bracket (I). Move cabinet away from wall and screw plastic anchor (K) into wall on pencil mark. 2. Place cabinet against wall, insert screw (L) through hole on bracket (I), then tighten to plastic anchor (K). Option #2: Securing to Drywall and Wood Stud 1. Position cabinet against wall in desired location.
ATTENTION ADULTS: Cabinet should be checked periodically for damage or loose screws/parts. Take appropriate action necessary to correct hazards such as tightening of screws and taking any damaged parts away from children. WARNING Please make sure your item is secured to the wall, per assembly instructions. CARE INSTRUCTIONS: Wipe clean with a water dampened cloth. Wipe dry with clean cloth.
Enjoy your new RiverRidge® Cabinet! Thank you for purchasing this RiverRidge® Home item. We hope you enjoy it and consider purchasing other RiverRidge® items. To order replacement parts at no cost to you, email customer.service@ssi-rr.com, call 1-(844)-223-5201 or order parts online at www.riverridgehome.com. Only valid in the United States. If purchased outside of the United States, please contact retailer where purchased. RiverRidge® is a registered trademark of Sourcing Solutions, Inc.
