ASSEMBLY INSTRUCTIONS RiverRidge® MEDORD SINGLE DOOR FLOOR CABINET ITEM# 06-102 WHITE ITEM# 06-103 ESPRESSO ADULT ASSEMBLY REQUIRED This product requires assembly by an adult because of small parts. Care should be taken in unpacking and assembling this item to keep small parts away from children. WARNING SEE FULL WARNING ON PAGE 2 Young children can be seriously injured or killed if furniture tips over. Don’t use this item for a TV stand or place heavy objects on top of item.
Send requests for missing or damaged parts by email to: customer.service@ssi-rr.com or call toll free 1-(844)-223-5201 or order parts on line at www.riverridgehome.com THIS CABINET WILL HOLD UP TO 25 POUNDS PER SHELF OR A TOTAL OF 75 POUNDS. DO NOT LOAD EACH SHELF WITH MORE THAN 25 POUNDS OR 75 POUNDS TOTAL WEIGHT. IF OVERLOADED WITH MORE THAN 25 POUNDS PER SHELF OR 75 POUNDS TOTAL WEIGHT, CABINET MAY TIP FROM WALL AND CAUSE SERIOUS INJURY OR DEATH.
PARTS LIST NO QTY DESCRIPTION 1 1PC TOP BOARD 2 1PC LEFT SIDE PANEL 3 1PC RIGHT SIDE PANEL 4 1PC CROSS BAR 5 1PC BACK BOARD 6 1PC DOOR 7 1PC ADJUSTABLE SHELF 8 1PC BOTTOM BOARD 9 1PC DRAWER FRONT BOARD 10 1PC DRAWER LEFT SIDE PANEL 11 1PC DRAWER RIGHT SIDE PANEL 12 1PC DRAWER BACK BOARD 13 1PC DRAWER BOTTOM BOARD
NO PARTS QTY DESCRIPTION A 10PCS CAM BOLT 5x35mm B 10PCS CAM LOCK 15x10mm C 4PCS WOOD DOWEL D 1PC MAGNET E 6PCS SCREW 3x14mm F 2PCS METAL BRACKET G 2PCS SCREW 3x10mm H 4PCS SHELF HOLDER I 5PCS SCREW 4x35mm J 1PC MAGNET PLATE K 2PCS DOOR PIN L 2PCS SCREW 4x25mm M 2PCS KNOB N 1PC PLASTIC LOCK STRIP O 1PC PLASTIC ANCHOR P 4PCS PLASTIC BRACKET Q 4PCS CAM BOLT 5x25mm R 4PCS CAM LOCK 12x10mm S 8PCS SCREW 3x12mm DRAWER SLIDER (ATTACH TO LEFT SIDE PANEL)
STEP 1 STEP 1 1. Screw 4 cam bolts (A) into pre-threaded holes on top board (1). 2. Attach 1 metal bracket (F) to top board (1) by inserting 1 screw (G) through hole on metal bracket (F) and tighten to top board (1). 3. Attach magnet plate (J) to door (6) by inserting 1 screw (G) through hole on magnet plate (J) and tighten to door (6) 4. Attach 1 knob (M) to door (6) by inserting 1 screw (L) through hole on door (6) and tighten to knob (M). 5. Insert 2 door pins (K) into holes on door (6).
STEP 3 STEP 3 1. Attach magnet (D) to cross bar (4) by inserting 2 screws (E) through holes on magnet (D) and tighten to cross bar (4). 2. Insert 2 wood dowels (C) into wood dowel holes on left side panel (2). 3. Attach cross bar (4) and bottom board (8) to left side panel (2) by inserting wood dowels (C) into wood dowel holes on cross bar (4) and bottom board (8). 4. Insert 3 cam locks (B) into cam lock holes on cross bar (4) and bottom board (8), then rotate clockwise to secure cam bolts in place.
STEP 5 STEP 5 1. Insert 2 wood dowels (C) into wood dowel holes on cross bar (4) and bottom board (8). 2. Attach right side panel (3) to cross bar (4) and bottom board (8) by inserting wood dowels (C) into wood dowel holes on right side panel (3). 3. Insert 3 cam locks (B) into cam lock holes on cross bar (4) and bottom board (8), then rotate clockwise to secure cam bolts in place. STEP 6 STEP 6 1. Slide back board (5) into grooves on left side panel (2), right side panel (3) and bottom board (8). 2.
STEP 7 STEP 7 1. Screw 4 cam bolts (Q) into pre-threaded holes on drawer front board (9). 2. Attach drawer left side panel (10) and drawer right side panel (11) to drawer back board (12) by inserting 4 screws (I) through holes on drawer left side panel (10) and drawer right side panel (11), then tighten to drawer back board (12). 3. Slide drawer bottom board (13) into grooves on drawer left side panel (10), drawer right side panel (11) and drawer back board (12). STEP 8 STEP 8 1.
STEP 9 STEP 9 1. Attach drawer slider (V) and (W) to bottom of assembled drawer by inserting 4 screws (S) through holes on drawer slider (V) and (W), then tighten to bottom of assembled drawer. STEP 10 STEP 10 1. Slide assembled drawer into cabinet. 2. Insert 4 shelf holders (H) into holes on left side panel (2) and right side panel (3) and make sure all 4 plastic holders (H) are on same level. 3. Place adjustable shelf (7) on the plastic holders.
STEP 11 STEP 11 1. Attach 4 brackets (P) to back of cabinet by inserting 4 screws (E) through holes on brackets (P) and tighten to cabinet. STEP 12 STEP 12 1. Place drawing with hole position on wall in desired location and drill 1 hole through the hole position on the drawing. 2. Insert plastic anchor (O) into hole on wall and attach metal bracket (F) to plastic anchor (O) by inserting 1 screw (I) through hole on metal bracket (F) and tighten to plastic anchor (O). 3.
