ASSEMBLY INSTRUCTIONS RiverRidge® Somerset Spacesaver ITEM #: 06-040 White ITEM #: 06-079 Gray ADULT ASSEMBLY REQUIRED This product requires assembly by an adult because of small parts. Care should be taken in unpacking and assembling this item to keep small parts away from children. During assembly children should be kept away from the product due to possible risk of injury. WARNING SEE FULL WARNING ON PAGE 2 Young children can be seriously injured or killed if furniture tips over.
THIS SHELF UNIT WILL HOLD UP TO 25 POUNDS PER SHELF OR A TOTAL OF 75 POUNDS. DO NOT LOAD EACH SHELF WITH MORE THAN 25 POUNDS OR 75 POUNDS TOTAL WEIGHT. IF OVERLOADED WITH MORE THAN 25 POUNDS PER SHELF OR 75 POUNDS TOTAL WEIGHT, SHELF MAY TIP FROM WALL AND CAUSE SERIOUS INJURY OR DEATH.
PARTS LIST NO QTY DESCRIPTION 1 2 3 1PC 1PC 1PC Left Door Right Door Upper Right Side Panel 4 6 7 8 9 10 11 12 13 14 15 16 17 18 1PC 1PC 1PC 1PC 1PC 1PC 1PC 1PC 1PC 1PC 2PCS 1PC 1PC 1PC Upper Left Side Panel Shelf Top Board Middle Connection Board Upper Back Board Middle Back Board Lower Back Board Adjustable Shelf Right Support Board Left Support Board Lower Section Top Cross Bar Rear Lower Cross Bar Lower Left Side Panel Lower Right Side Panel
NO A B PARTS QTY DESCRIPTION 16PCS Wood Dowel 22PCS Cam Bolt C 22PCS Cam Lock D 18PCS Screw (3x12mm) E 4PCS Hinge F G 2PCS Magnet Plate 24PCS Screw (2.5x12mm) H 1 SET Magnet With 2 Screws I 4PCS Shelf Holder J 4PCS Machine Screw (4x12mm) K 2PCS Handle L 2PCS Plastic Anchor M 2PCS Screw (4x30mm) N O 1PC Plastic Connection Strip 4PCS Screw (3.
STEP 1 1. Attach 1 magnet plate (F) to left door (1) by inserting 1 screw (D) through hole on magnet plate (F), then tighten to left door (1). 2. Attach 1 handle (K) to left door (1) by inserting 2 machine screws (J) through holes on left door (1), then tighten to handle (K). 3. Repeat above steps to assemble another magnet plate (F) and handle (K) to right door (2). STEP 2 1. Insert 2 wood dowels (A) into dowel holes on right support board (13) . 2.
STEP 3 1. Attach right support board (13) to upper right side panel (3) by inserting wood dowels (A) into dowel holes and inserting cam bolts (B) into cam lock holes on upper right side panel (3). 2. Insert 3 cam locks (C) into cam lock holes on upper right side panel (3), then rotate clockwise to secure cam bolts (B) in place. 3. Repeat above steps to assemble upper left side panel (4) and right support board (14). STEP 4 1.
STEP 5 1. Attach magnet (H) to bottom of top board (7) by inserting 2 screws through holes on magnet (H), then tighten to top board (7). 2. Insert 2 screws (Q) through sliding bracket (P) into holes on top board (7) 3. Screw 4 cam bolts (B) into cam bolt holes on top board (7). 4. Attach top board (7) to upper left side panel (4) and upper right side panel (3) by inserting cam bolts (B) into cam lock holes on upper left side panel (4) and upper right side panel (3). 5.
STEP 7 1. Screw 2 cam bolts (B) into cam bolt holes on middle connection board (8). 2. Insert 8 wooden dowels (A) into holes on lower left side panel (17), lower right side panel (18) and lower section top cross bars (15). 3.
STEP 8 1. Screw 4 cam bolts (B) into cam bolt holes on middle connection board (8). STEP 9 1. Attach upper assembled section to lower assembled section by inserting 4 cam bolts (B) into cam lock holes on upper left side panel (4) and upper right side panel (3). 2. Insert 4 cam locks (C) into cam lock holes on upper left side panel (4) and upper right side panel (3), then rotate clockwise to secure cam bolts (B) in place.
STEP 10 1. Attach upper back board (9) and middle back board (10) together by sliding into plastic connection strip (N). 2. Attach upper back board (9) and middle back board (10) to cabinet by inserting 8 screws (G) through holes on upper back board (9), and 4 screws (G) through holes on middle back board (10), then tighten to cabinet. 3. Attach lower back board (11) to cabinet by inserting 8 screws (G) through holes on lower back board (11), then tighten to cabinet. 4.
STEP 12 Option #1: Securing to Drywall 1. Position spacesaver against wall in desired location. Using a pencil, make 2 small marks on wall through holes on brackets (P). Move cabinet away from wall and screw 2 plastic anchors (L) into wall on pencil marks. 2. Place cabinet against wall, insert 2 screws (M) through holes on brackets (P), then tighten to plastic anchors (L). Option #2: Securing to Drywall and Wood Stud 1. Position spacesaver against wall in desired location.
ATTENTION ADULTS: Cabinet should be checked periodically for damage or loose screws/parts. Take appropriate action necessary to correct hazards such as tightening of screws and taking any damaged parts away from children. WARNING Please make sure your item is secured to the wall, per assembly instructions. CARE INSTRUCTIONS: Wipe clean with a water dampened cloth. Wipe dry with clean cloth. IMPORTANT: Keep assembly instructions for future reference.
Enjoy your new RiverRidge® Spacesaver! Thank you for purchasing this RiverRidge® Home item. We hope you enjoy it and consider purchasing other RiverRidge® items. To order replacement parts at no cost to you, email customer.service@ssi-rr.com, call 1-(844)-223-5201 or order parts online at www.riverridgehome.com. Only valid in the United States. If purchased outside of the United States, please contact retailer where purchased. RiverRidge® is a registered trademark of Sourcing Solutions, Inc.
