Owner`s manual

qtc9322c.pm5
Quick Talk Advanced Features/ Applications Manual
TABLE OF CONTENTS
DESCRIPTION PAGE
WHAT THIS MANUAL COVERS ............................................... ii
WARNING: IMPORTANT SAFETY INFORMATION .................. ii
ACCESSORIES FOR QUICK TALK .......................................... ii
GENERAL INFORMATION ........................................................ 1
QUICK TALK FEATURES ......................................................... 1
IDENTIFICATION OF CONTROLS & CONNECTIONS ............. 2
COVER GASKET INSTALLATION/ REPLACEMENT ............... 3
PROGRAMMING YOUR QUICK TALK ..................................... 4
PULSE TELEPHONE CONFIGURATION ................................. 4
TO PROGRAM QUICK TALK BY TELEPHONE ....................... 4
1. Configure Switch Terminals (1 or 2 switches)................ 5
2. Adding a Second Switch to Disable ................................
the Quick Talk Transmitter ........................................... 5
3. Programming Quick Talk Transmitter Frequency .......... 6
4. Setting a Special Transmit Frequency ........................... 7
5. Programming Quiet Call Sub-Audible .............................
Squelch Interference Eliminator .................................. 7
6. Programming Digital Quiet Call Sub-Audible...................
Squelch Interference Eliminator .................................. 8
7. Test Quick Talk Radio Transmitter ................................. 8
8. Testing Switch Open & Closed Conditions .................... 9
9. Recording Location & Switch Condition ..........................
Voice Phrases ........................................................... 10
10. Number of Recorded Voice Phrase Repeats .................
for Each Message Transmission ............................... 11
11. Programming the Switch Status ......................................
Broadcast Schedule .................................................. 11
12. Programming a Message Repeat Limit ....................... 12
13. Restart Quick Talk when Finished Programming ............
Message Parameters ................................................ 12
14. To Reprogram Quick Talk to Original ...............................
Factory Settings ........................................................ 12
15. Setting Debounce Options
Normal Debounce ..................................................... 13
Holdoff Debounce ...................................................... 13
16. Monitoring 4-20 mA Sensor Current Loops .....................
w/ Analog Modes ....................................................... 14
17. Solar Panels for Operating & Charging ...........................
Ni-Cd Batteries .......................................................... 14
18. Using Latching Option ................................................. 14
19. J103 Settings for Battery Type
Alkaline Batteries....................................................... 15
Ni-Cd Batteries .......................................................... 15
20. Setting Analog Modes ................................................. 15
Analog Input Mode .................................................... 16
Terminated Alarm Input Mode ................................... 16
21. Recording Unique Low Battery Messages .................. 17
22. Recording Unique Power Failure Messages ............... 17
23. Enabling/ Disabling Status Messages ......................... 17
24. Setting Battery Saver Options ..................................... 17
25. Setting Narrow-Band (2.5 kHZ) Channels ................... 18
26. Connecting an External 12 VDC Power Supply ........... 18
27. Configuring Transmit Delay ......................................... 18
28. Pre-installation Checklist ............................................. 18
29. Quick Talk Installation.................................................. 19
CARE & MAINTENANCE ........................................................ 19
QUICK REFERENCE GUIDE ............................................ 20, 21
This manual, Ritron Item RQT-UM2, covers advanced operation of the Quick Talk Voice Notification Radio Transmitter,
including the more complex features not covered in the Basic Owner's Manual, Ritron Item RQT-UM1 (14500006).
For further information on the Quick Talk, visit Ritron's website at
http://www.ritron.com, or call Ritron at 317-846-1201.
WHAT THIS MANUAL COVERS
NOTICE: DO NOT use the Quick Talk unit to report conditions
relating to safety of life or property. To reduce the
risk of fire, electric shock or personal injury, follow
these basic safety instructions when using this unit.
1. Read and follow all instructions.
2. Disconnect the unit before cleaning. Do not use liquid or
aerosol cleaners.
3. Use only approved power sources for the unit.
4. During thunderstorms, avoid contact with this unit and any
external antenna system or wiring.
5. The Quick Talk switch and external power terminals are
connected internally through ground to the antenna connector. If
the Quick Talk switch or power supply terminals contact high
voltage, a hazardous condition may exist in that contacting the
antenna could prove injurious or even fatal.
6. In general, the switches you connect to the Quick Talk are to be
independent dry contact switches, and not part of any other
"live" electrical circuit
7. If you are unsure whether your installation will be safe, contact
an experienced electrician or electronics technician.
— — —
WARNING
— — —
IMPORTANT SAFETY INFORMATION
These replacement and optional items are available from Ritron
and its authorized dealers.
ITEM DESCRIPTION
AFB-1545 Standard 16 in. Flexible Whip Antenna
RAM-1545 Magnetic-Mount Antenna w/ 20 ft. Cable
& BNC Connector
ACCESSORIES FOR QUICK TALK
DESCRIPTION PAGE
FIG—1: CONTROL & CONNECTION LOCATIONS ................ 2
FIG—2: COVER ASSEMBLY ................................................... 3
FIG—3: CONNECTIONS FOR TESTING SWITCHES ............ 9
FIG—4: TYPICAL MESSAGE CONFIGURATION ................. 10
FIG—5: CURRENT LOOP .........................................................
(EXAMPLE CONNECTION DIAGRAM)................... 14
FIG—6: J103 POSITION FOR USE WITH .................................
ALKALINE BATTERIES .......................................... 15
FIG—7: J103 POSITION FOR USE WITH .................................
NI-CD BATTERIES ................................................. 15
FIG—8: ANALOG INPUT MODE (EXAMPLE)....................... 16
FIG—9: TERMINATED ALARM INPUT MODE (EXAMPLE) . 16
FIG—10: J102 SETTING FOR NARROW BAND ......................
OPERATION .......................................................... 18
FIG—11: EXTERNAL POWER SUPPLY CONNECTIONS .... 18
FIG—12: QUICK TALK INSTALLATION ................................ 19
TABLE OF FIGURES
Page ii