Owner`s manual

qtm9322b.pm5
For assistance, call RITRON at 800-872-1872, or go to www.ritron.comPage 4
What is my Radio System Frequency? Ritron pioneered
the Color Dot system to simplify the identification of radio
system frequencies for Ritron Jobcom radios. Color Dots
are placed on the bottoms of and inside the enclosures of
all Jobcom radios. Other manufacturers have also
adopted this idea.
To identify your assigned frequency if your radios do not
have a color dot, locate a label identifying the receiver
frequency in megahertz (MHz). Your assigned frequency is
also shown on your F.C.C. Station License. Call your radio
dealer or Ritron for help if you cannot determine your
radio's receiver frequency.
Do I need to program my Quick Talk's transmitter
frequency? The original factory-programmed transmitter
frequency of your Quick Talk is marked on the outside of
the shipping box, and is also indicated by a color dot on
the inside the unit case. If the Quick Talk frequency
matches your radio system frequency, and if the Quick
Talk has not been reprogrammed since it left the factory,
you may skip this section and proceed to the next.
Note: To program a non-table frequency refer to page 14.
TO PROGRAM THE QUICK TALK TRANSMITTER
FREQUENCY:
a. Determine the frequency of your radio system.
b. Find your frequency in the appropriate table at right,
and determine its corresponding two digit code. If
your radio system frequency is not in the chart, your
Quick Talk must be programmed by a radio dealer
or by Ritron.
c. Pick up the telephone receiver, and listen for the
acknowledge tone. Dial "11", then the digits of the
selected frequency code from the table.
Examples: If the Quick Talk is a VHF RQT-150
model, and the radios operate on
154.570 MHz (Blue Dot frequency),
dial "11-02".
If the Quick Talk is a UHF RQT-450
model, and the radios operate on
467.925 MHz (Blue Star frequency),
dial "11-08".
d. Quick Talk responds with a single beep to indicate
it has programmed the transmitter frequency.
e. You may either hang up or continue programming.
NOTES: If you make a dialing mistake while program-
ming, hang up the telephone handset, then
pick it up and dial again.
If you reprogrammed the Quick Talk frequency,
you may wish to remove the Color Dot from
inside the case, to avoid later confusion.
What the Tones (Beeps) in Your Earpiece Mean:

A series of three short tones cues you to begin
recording a message.

A single brief tone means your command is
accepted and stored.

A series of long repeating tones means your
command was not understood; hang up and dial
again.
UHF Business Band
Model RQT-450
MHz Frequency Color
QUICK
TALK
FREQ. CODE
01 154.600 .... Green Dot
02 154.570 .... Blue Dot
03 151.625 .... Red Dot
04 151.955 .... Purple Dot
05 151.925
06 154.540
07 154.515
08 154.655
09 151.685
10 151.715
11 151.775
12 151.805
13 151.835
14 151.895
15 154.490
16 151.655
17 151.745
18 151.865
VHF Business Band
Model RQT-150
MHz Frequency Color
QUICK
TALK
FREQ. CODE
01 467.7625 ..... J
02 467.8125 ..... K
03 464.5500 ..... Yellow Dot
04 464.5000 ..... Brown Dot
05 467.8500 ...... Silver Star
06 467.8750 ...... Gold Star
07 467.9000 ...... Red Star
08 467.9250 ...... Blue Star
09 469.2625
10 462.5750 ...... White Dot
11 462.6250 ...... Black Dot
12 462.6750 ...... Orange Dot
13 464.3250
14 464.8250
15 469.5000
16 469.5500
17 463.2625
18 464.9125
19 464.6000
20 464.7000
TABLE 1: TRANSMIT FREQUENCY CODES
PROGRAMMING YOUR QUICK TALK TRANSMITTER FREQUENCY
(VHF Business Band)
(UHF Business Band)