Owner`s manual

For assistance, call RITRON at 800-872-1872, or go to www.ritron.com
Page 21
(Quick Reference Guide, continued from page 24)
DIAL CODE DESCRIPTION
PHRASE REPEATS IN EACH MESSAGE: (continued)
SWITCH 1 CLOSED
7-1-2-1 One time  DEFAULT
7-1-2-2 Two times
7-1-2-3 Three times
7-1-2-4 Four times
7-1-2-5 Five times
7-1-2-6 Six times
7-1-2-7 Seven times
7-1-2-8 Eight times
7-1-2-9 Nine times
SWITCH 2 OPEN
7-2.1-1 One time  DEFAULT
7-2-1-2 Two times
7-2-1-3 Three times
7-2-1-4 Four times
7-2-1-5 Five times
7-2-1-6 Six times
7-2-1-7 Seven times
7-2-1-8 Eight times
7-2-1-9 Nine times
SWITCH 2 CLOSED
7-2-2-1 One time  DEFAULT
7-2-2-2 Two times
7-2-2-3 Three times
7-2-2-4 Four times
7-2-2-5 Five times
7-2-2-6 Six times
7-2-2-7 Seven times
7-2-2-8 Eight times
7-2-2-9 Nine times
DEBOUNCE OPTIONS
SWITCH 1 MODENORMAL
8-1-1 Normal On/ Off
SWITCH 1 MODEDEBOUNCED CONTACT
8-1-2-1 No contact debounce
8-1-2-2 10 seconds of debounce
8-1-2-3 30 seconds of debounce
8-1-2-4 1 minute of debounce
8-1-2-5 3 minutes of debounce
8-1-2-6 5 minutes of debounce
SWITCH 1 MODEHOLDOFF CONTACT
8-1-3-1 No contact holdoff
8-1-3-2 10 seconds of holdoff
8-1-3-3 30 seconds of holdoff
8-1-3-4 1 minute of holdoff
8-1-3-5 3 minutes of holdoff
8-1-3-6 5 minutes of holdoff
SWITCH 2 MODENORMAL
8-2-1 Normal On/ Off
SWITCH 2 MODEDEBOUNCED CONTACT
8-2-2-1 No contact debounce
8-2-2-2 10 seconds of debounce
8-2-2-3 30 seconds of debounce
8-2-2-4 1 minute of debounce
8-2-2-5 3 minutes of debounce
8-2-2-6 5 minutes of debounce
SWITCH 2 MODEHOLDOFF CONTACT
8-2-3-1 No contact holdoff
8-2-3-2 10 seconds of holdoff
8-2-3-3 30 seconds of holdoff
8-2-3-4 1 minute of holdoff
8-2-3-5 3 minutes of holdoff
8-2-3-6 5 minutes of holdoff
DIAL CODE DESCRIPTION
LATCHING OPTIONS /
SWITCH 1 MODEON/ OFF
8-1-4 Latch off  DEFAULT
8-1-5 Latch on
SWITCH 1 MODEINPUT TYPE
8-1-6-1 Contact closure  DEFAULT
8-1-6-2 Analog Input
8-1-6-3 Terminated Alarm Input
SWITCH 1 MODELOW THRESHOLD SETPOINT
8-1-7-x-x-x 0-0-0 = 0 volt
0-5-1 = 1 volt
0-8-4 = 1.68 volts  DEFAULT
1-0-2 = 2 volts
1-5-3 = 3 volts
2-0-4 = 4 volts
2-5-5 = 5 volts
SWITCH 1 MODEHIGH THRESHOLD SETPOINT
8-1-8-x-x-x 0-0-0 = 0 volt
0-5-1 = 1 volt
1-0-2 = 2 volts
1-5-3 = 3 volts
1-7-1 = 3.42 volts  DEFAULT
2-0-4 = 4 volts
2-5-5 = 5 volts
/
SPECIAL FEATURES:
CONFIGURATION
9-1-1 Configure to One Contact Input  DEFAULT
9-1-2 Configure to Two Contact Inputs
ALERT BEEPS
9-2-1 One beep  DEFAULT
9-2-2 Two beeps
9-2-3 Three beeps
9-2-4 No beeps
BATTERY SAVER
9-3-1 Off
9-3-2 On  DEFAULT
LOW BATTERY MESSAGE
9-4-1 Off
9-4-2 On  DEFAULT
9-4-3 Alkaline batteries  DEFAULT
9-4-4 Ni-Cd batteries . . . . . . . . . . . . .
EXTERNAL POWER MESSAGE
9-5-1 Off  DEFAULT
9-5-2 On
TRANSMIT DELAY IN 1/32 SECOND INCREMENTS
9-6-x-x-x 0-0-0 = No Delay
0-2-4 = 3/4 second  DEFAULT
0-3-2 = 1 second
0-6-4 = 2 seconds
0-9-6 = 3 seconds
1-2-8 = 4 seconds
1-6-0 = 5 seconds
1-9-2 = 6 seconds
2-2-4 = 7 seconds
2-5-5 = 7-
31
/ 32 seconds
RESTORE FACTORY DEFAULTS
9-7-8 VHF (Frequency = 154.570 MHz)
9-7-9 UHF (Frequency = 467.925 MHz)
END TELEPHONE PROGRAMMING
9-9-9 End telephone programming & RESTART
{
NOTE:
For
Switch 1
ONLY
{
IMPORTANT:
See J103
settings,
page 15.
Q UICK T ALK A DVANCED F EATURES