Owner`s manual
Have questions? Call
800-USA-1-USA
(800-872-1872) or visit our website at www.ritron.com
01 67.0 18 123.0 35 225.7
02 71.9 19 127.3 36 233.6
03 74.4 20 131.8 37 241.8
04 77.0 21 136.5 38 250.3
05 79.7 22 141.3 39 69.4
06 82.5 23 146.2 40 159.8
07 85.4 24 151.4 41 165.5
08 88.5 25 156.7 42 171.3
09 91.5 26 162.2 43 177.3
10 94.8 27 167.9 44 No Tone
11 97.4 28 173.8 45 183.5
12 100.0 29 179.9 46 189.9
13 103.5 30 186.2 47 196.6
14 107.2 31 192.8 48 199.5
15 110.9 32 203.5 49 206.5
16 114.8 33 210.7 50 229.1
17 118.8 34 218.1 51 254.1
00 Delete
HOW TO DELETE A CHANNEL
1. Follow the instructions in FIG-6 on page 7 to place
the radio in the Program/ Readout Mode.
2. Using the Channel button and the LED display on
the front of the radio, select the channel to be
deleted.
3. Enter 4-digit code "0000" as described in the "How
to Field Program Frequency & Tone Codes" section
on page 8.
4. When all four digits are programmed, press and
release the On/ Volume Up to SAVE your program-
ming entry. The LED display will briefly show the
channel number you have just deleted and the radio
will sound a triple beep to indicate that channel dele-
tion was successful.
5. To delete another channel, repeat steps 2 through 4.
6. Turn the radio OFF and then ON againthe radio is
now ready to use.
7. The remaining channels are in the same sequence
and will retain their same channel number. The
Channel Selector will skip over the deleted channel
numbers.
NOTE: If all channels are deleted the radio will
not operate, instead it will turn on in Field
Program mode to allow entry of a valid
frequency and tone code.
RADIO PROGRAMMING
page 10
TABLE 2: INTERFERENCE ELIMINATOR
PROGRAMMABLE QC TONE
CODES
TABLE 3: DIGITAL INTERFERENCE ELIMINATOR
PROGRAMMABLE DQC CODES
Code Numbers
Code No. Hz
Code No. Hz Code No. Hz
356
364
365
371
411
412
413
423
431
432
445
446
452
454
455
023
025
026
031
032
036
043
047
051
053
054
065
071
072
073
074
114
115
116
122
125
131
132
134
143
145
152
155
156
162
165
172
174
205
212
223
225
226
243
244
245
246
251
252
255
261
263
265
266
271
274
306
311
315
325
331
332
343
346
351
462
464
465
466
503
506
516
523
532
546
565
606
612
624
627
631
632
645
654
662
664
703
712
723
731
732
734
743
754
HOW TO FIELD PROGRAM RADIO OPTIONS
1. Follow the instructions in FIG-6 on page 7 to place
the radio in the Program/ Readout Mode.
2. Using the PTT (push-to-talk) button and the LED
display, enter the single digit code from Table 4
below for the option to be programmed.
3. Pausethe display will change and show a hyphen,
you will also hear a short low tone.
4. Press and release the On/Volume Up to SAVE your
programming entry. The radio will sound a triple beep
to indicate that programming was successful.
5. Turn the radio OFF and then ON againthe radio is
now ready to use.
Turn Channel Scan ON 1
Turn Channel Scan OFF 2
Turn Weather Channel ON 3
Turn Weather Channel OFF 4
Turn Weather Alert ON 5
Turn Weather Alert OFF 6
Turn Speaker Beep ON 7
Turn Speaker Beep OFF 8
TABLE 4: RADIO OPTION CODES
OPTION CODE NO.