Other Content

Location of Controls
1. 4 Super Bright LEDs
2. ON/OFF Switch with Selectable Dimmer
3. Folding Neck
4. Dual Adjustable Light Heads
5. EZ Mount Bracket
6. Built-In Bubble Level
7. Battery Compartment*
*behind EZ Mount Bracket
Installation
EZ Mount Bracket
1. First remove printed paper mounting template from back of unit.
2. Drill two (2) pilot holes in the location where you want to mount the picture light. Place screws
(included) in pre-drilled holes. Tighten slightly until secure, but do not tighten all the way.
Slide EZ Mount Bracket keyhole slots over screw heads and into position.
3. Use the built-in bubble level to make sure the mounting bracket is level before securing it to the wall.
4. Once you confi rm that the bracket is level, tighten the screws to secure it to the wall. Take care to not over
tighten.
5. To hang the picture light on the mounting bracket, align the picture light with the mounting bracket and
slide the unit down. Light will lock into position.
6. To remove the picture light from the mounting bracket;
A) Hold the picture light by the base (not light head).
B) Slide the unit up.
C) Once the body releases from mounting bracket, pull the unit towards you.
Operating Directions
Light Positioning
Fold the neck out to desired position. Pivot each light head independently to desired angle.
NOTE: Each light head can only be turned 180° up or down (Fig 1). To prevent damage to the unit, do NOT
overturn the light heads. Doing so may damage the unit and will void the warranty.
ON/OFF Operation with Selectable Dimmer
• Press once for full brightness.
• Press and hold until the LEDs reach the desired brightness then release the button.
• Press a third time to turn the light OFF.
Inserting/Replacing the Batteries
If the LEDs appear to be dim this is an indication that your batteries need to be replaced.
Installing Batteries for the First Time:
1. Remove the mounting bracket from the unit by sliding it down.
2. Open the battery compartment cover.
3. Insert 3 AA batteries.
4. Make sure to follow battery polarity guide when installing new batteries.
5. Replace battery compartment cover.
To Replace Batteries Once Mounted:
1. To remove the picture light from the mounting bracket;
A) Hold the picture light by the base (not light head).
B) Slide the unit up.
C) Once the body releases from mounting bracket, pull the unit towards you.
2. Open the battery compartment cover.
3. Remove old batteries and replace with 3 new AA batteries.
4. Make sure to follow battery polarity guide when installing new batteries.
5. Replace battery compartment cover and remount the light.
Battery Precautions:
1. Use only the size and type of batteries specifi ed.
2. Always purchase the correct size and grade of battery most suitable for the intended use.
3. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment.
Reversed batteries may cause damage to the device.
4. Do not mix alkaline, standard (Carbon-Zinc), or rechargeable (Nickel Cadmium) batteries.
5. Replace all batteries of a set at the same time. Do not mix old and new batteries.
6. Clean the battery contacts and also those of the device prior to battery installation.
7. Do not dispose of batteries in fi re.
8. Remove batteries if consumed or if product is to be left unused for an extended period of time.
LPL601XL/LPL601XLB/LPL601XLG Owner’s Manual
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: Modifi cations to this product not approved by the party responsible for compliance could void the user’s authority to operate the product.
One-Year Limited Warranty
AmerTac warrants to the original purchaser that this product will be free from defects in materials
and workmanship for a period of one year from the date of purchase. Additional details are
available at www.amertac.com. PROP. 65 WARNING: This product contains chemicals known to
the State of California to cause cancer and/or birth defects or other reproductive harm.
©2016 AmerTac™
250 Boulder Drive
Breinigsville, PA 18031
www.amertac.com
Made in China / Fabriqué en Chine / Hecho en China
I16-0002-A
WIRELESS LED
PICTURE LIGHT
screws
a
y.
g it to the wall.
1
2
3
4
5
7
6
Unit Back
Fig 1
MOUNTING
SURFACE
UNIT
Picture Frame
Mounting Bracket
Unit Slides Down
Onto Mounting Bracket
Screw
Mounting Bracket
Keyhole Slots
UNIT BACK
Built-In
Bubble Level
1.5V AA / UM3
X3