User manual

Warranty
We accept no responsibility for the use, installation, application,
or maintenance of this product. No liability shall be assumed
nor accepted for any damages, losses, injury or costs resulting
from the use of the product. As far as is legally permitted, the
obligation for compensation is limited to the invoice amount of
the product in question.
WEEE
Electrical equipment marked with the crossed wheelie
bin symbol must not be discarded in the standard
household waste; instead it should be taken to a
suitable specialist disposal location or your dealer.
Company Information
Please contact your place of purchase first in regards to any
enquiries/warranty claims.
Address:
Ripmax Ltd,
241 Green Street,
Enfield,
EN37SJ
United Kingdom
Website: http://www.ripmax.com
Phone: [phone]
Please fit wire or oleo legs to suit your model. The pivot blocks
have recessed grub screws to pinch the wire. They will be in the
face or side of the block itself or in the brass bush in the side of
the main body. It varies from unit to unit. Make sure you have
flats on the wire for the grubs screws to bite against. They will not
stop the leg rotating if only pinching on the circumference.
Mount your retract unit on beams that are flat/parallel so that
the unit is not twisted in any way when screwed down. A twisted
body will draw more current.
Each unit has over-current protection. If the leg is stopped in any
way during movement, or the load is too high, it will stop at that
point of the movement cycle to prevent burning the motor. Cycle
the gear in the opposite direction to reset. Bear in mind this will
happen to an individual leg only, not all at the same time. The
sensing is on each unit and independent.
Ripmax
Part No. Description
Dimensions
(L x W x H)
Mount
Plate
L x W
Maximum
Model
Weight
Weight
Each
Operating
Voltage
Speed
4.8v(Secs)
Speed
6.0v(Secs)
Speed
7.4v(Secs)
Torque
4.8v
(Kg.cm)
Torque
6.0v
(Kg.cm)
Torque
7.4v
(Kg.cm)
Stall
Current Amplifier Gears
Leg Wire/
Stub
Diameter
F-RMXER010M Mains Micro 54 x 32 x 21 24.5 x 32 2Kg 24.5g 4.8 - 6.0v 0.50 0.45 N/A 1.70 2.60 N/A 0.9 to 1A Digital Metal 3mm
F-RMXER010N Nose Micro 54 x 32 x 21 24.5 x 32 2Kg (Trike) 22.5g 4.8 - 6.0v 0.50 0.45 N/A 1.70 2.60 N/A 0.9 to 1A Digital Metal 3mm
F-RMXER020M Mains Small 66 x 35 x 25 33 x 35 3Kg 43.5g 4.8 - 6.0v 0.70 0.55 N/A 2.30 3.00 N/A 0.9 to 1A Digital Metal 4mm
F-RMXER020MS Mains Small (Stub) 66 x 35 x 25 33 x 35 3Kg 46g 4.8 - 6.0v 0.70 0.55 N/A 2.30 3.00 N/A 0.9 to 1A Digital Metal 4mm
F-RMXER020N Nose Small 66 x 35 x 25 33 x 35 3Kg (Trike) 50g 4.8 - 6.0v 0.70 0.55 N/A 2.30 3.00 N/A 0.9 to 1A Digital Metal 4mm
F-RMXER030M Mains Medium 74 x 44 x 28 43 x 44 5Kg 67.6g 4.8 - 6.0v 0.80 0.60 N/A 2.90 3.10 N/A 1.2 to 1.4A Digital Metal 5mm
F-RMXER030MS Mains Medium (Stub) 74 x 44 x 28 43 x 44 5Kg 74g 4.8 - 6.0v 0.80 0.60 N/A 2.90 3.10 N/A 1.2 to 1.4A Digital Metal 5mm
F-RMXER030N Nose Medium 74 x 44 x 28 43 x 44 5Kg (Trike) 80g 4.8 - 6.0v 0.80 0.60 N/A 2.90 3.10 N/A 1.2 to 1.4A Digital Metal 5mm
F-RMXER040M Mains Large 92 x 51 x 31 44 x 51 10Kg 89g 4.8 - 7.4v 6.00 5.00 4.00 15.50 18.60 20.60 2.1 to 3A Digital Metal 5mm
F-RMXER040MS Mains Large (Stub) 92 x 51 x 31 44 x 51 10Kg 92g 4.8 - 7.4v 6.00 5.00 4.00 15.50 18.60 20.60 2.1 to 3A Digital Metal 5mm
F-RMXER040N Nose Large 92 x 51 x 31 44 x 51 10Kg (Trike) 96g 4.8 - 7.4v 6.00 5.00 4.00 15.50 18.60 20.60 2.1 to 3A Digital Metal 5mm
F-RMXER050M Mains Metal Large 92 x 51 x 31 43 x 51 20Kg 186g 4.8 - 7.4v 6.00 5.00 4.00 15.50 18.60 20.60 2.1 to 3A Digital Metal 10mm
F-RMXER050N Nose Metal Large 92 x 51 x 31 43 x 51 20Kg (Trike) 172g 4.8 - 7.4v 6.00 5.00 4.00 15.50 18.60 20.60 2.1 to 3A Digital Metal 8mm