manual

STEP 4
Apply a generous amount of
Q10creamtothearmwherethe
wristbandwillbelocated.Slip
on the elasticated wrist band
and position where the cream
hasbeenapplied.
STEP 5
Apply a generous amount of
Q10 cream to each hand and
putontheglove.
Ensurethereisagapbetween
thewristbandandgloveatall
times.
STEP 6
Presstheon/offbuttontoswitch
on.Theunitwillselftestandthe
statuslightwillilluminategreen.
STEP 7
Turn the output dial clockwise
to start the treatment. Further
clockwise movement will
increase the intensity. The
treatment light will flash to
indicate the treatment is in
progress. Reduce the intensity
by turning the output dial
anti-clockwise.
STEP 8
Thetreatmentlasts20minutes.
Attheendofthetreatmentthe
statuslightwillflashredandthe
unit will beep for 20 seconds
beforeturningitselfoff.
Note The unit can be turned off at any time by
pressing and holding the on/off button until
the unit beeps 4 times.
(+)
(–)
(+)
(–)
+– –+
7
HANDREJUVENATION
Hand Rejuvenation uses microcurrent ion
technology to pump smoothing and softening
agents deep into the skin. The treatment is
completedinjust20minutes.
SETUP
The gloves must be connected to the positive
(+)socket of the connectorlead and the wrist
bandsto the negative (–)socket to ensure the
active ions in the Q10 treatment cream are
pumpedintotheskin.
PATCHTEST
24hoursbeforeusingyourHandRejuvenation,it
is essential to do a patch test. Choose a small
areaontheinsideofyourwristandapplyasmall
amountofQ10treatmentcream.Ifdiscomfortor
allergic reaction occurs within 24 hours,
discontinueuse.
CONTENTS
1 ControlUnit
2 On/OffButton
3 Statuslight
4 Outputdial
5 Treatmentlight
6 Gloveswithleads
7 WristBandswithleads
8 Connectorleads
9 Q10treatmentcream
10 PP3Battery
+ - + -
3
6
7
9
10
8
1
5
4
2
6
IMPORTANT
• Ion pump technology uses gentle
microcurrents which on higher levels can be
felt as a gentle tingling sensation. During
treatment, as the active ingredients are
pumped into the skin, the tingling sensation
willbecomelessnoticeable.Thisoccursover
the first 10–15 minutes depending on how
muchcreamisapplied.
• For best results initially use daily. Thereafter
useasrequired.
• Alwaysensurethereisagapbetweenthewrist
bandandglove.
• Removeallpiercingsandjewelleryfromhands
andwrists.
• Washhandsanddrybeforeuse.
TREATMENT
Tip: Start by setting up just one glove to treat
one hand. You will then be able to appreciate
the difference a single treatment can make.
STEP 1
Plugeachgloveintothepositive
(+) socket of the connector
lead.
STEP 2
Plug each wrist band into the
corresponding negative (–)
socketoftheconnectorlead.
STEP 3
Check the unit is off with the
outputcontrolsetto0.Plugthe
two connector leads into the
bottomofthecontrolunit.
Ensurebothleadsarepushed
firmlyandfullyin.
4
5
– + –+
1
– + –+
2
3
8
STEP 4
Apply a generous amount of
Q10creamtothearmwherethe
wristbandwillbelocated.Slip
on the elasticated wrist band
and position where the cream
hasbeenapplied.
STEP 5
Apply a generous amount of
Q10 cream to each hand and
putontheglove.
Ensurethereisagapbetween
thewristbandandgloveatall
times.
STEP 6
Presstheon/offbuttontoswitch
on.Theunitwillselftestandthe
statuslightwillilluminategreen.
STEP 7
Turn the output dial clockwise
to start the treatment. Further
clockwise movement will
increase the intensity. The
treatment light will flash to
indicate the treatment is in
progress. Reduce the intensity
by turning the output dial
anti-clockwise.
STEP 8
Thetreatmentlasts20minutes.
Attheendofthetreatmentthe
statuslightwillflashredandthe
unit will beep for 20 seconds
beforeturningitselfoff.
Note The unit can be turned off at any time by
pressing and holding the on/off button until
the unit beeps 4 times.
(+)
(–)
(+)
(–)
+– –+
7
HANDREJUVENATION
Hand Rejuvenation uses microcurrent ion
technology to pump smoothing and softening
agents deep into the skin. The treatment is
completedinjust20minutes.
SETUP
The gloves must be connected to the positive
(+)socket of the connectorlead and the wrist
bandsto the negative (–)socket to ensure the
active ions in the Q10 treatment cream are
pumpedintotheskin.
PATCHTEST
24hoursbeforeusingyourHandRejuvenation,it
is essential to do a patch test. Choose a small
areaontheinsideofyourwristandapplyasmall
amountofQ10treatmentcream.Ifdiscomfortor
allergic reaction occurs within 24 hours,
discontinueuse.
CONTENTS
1 ControlUnit
2 On/OffButton
3 Statuslight
4 Outputdial
5 Treatmentlight
6 Gloveswithleads
7 WristBandswithleads
8 Connectorleads
9 Q10treatmentcream
10 PP3Battery
+ - + -
3
6
7
9
10
8
1
5
4
2
6
IMPORTANT
• Ion pump technology uses gentle
microcurrents which on higher levels can be
felt as a gentle tingling sensation. During
treatment, as the active ingredients are
pumped into the skin, the tingling sensation
willbecomelessnoticeable.Thisoccursover
the first 10–15 minutes depending on how
muchcreamisapplied.
• For best results initially use daily. Thereafter
useasrequired.
• Alwaysensurethereisagapbetweenthewrist
bandandglove.
• Removeallpiercingsandjewelleryfromhands
andwrists.
• Washhandsanddrybeforeuse.
TREATMENT
Tip: Start by setting up just one glove to treat
one hand. You will then be able to appreciate
the difference a single treatment can make.
STEP 1
Plugeachgloveintothepositive
(+) socket of the connector
lead.
STEP 2
Plug each wrist band into the
corresponding negative (–)
socketoftheconnectorlead.
STEP 3
Check the unit is off with the
outputcontrolsetto0.Plugthe
two connector leads into the
bottomofthecontrolunit.
Ensurebothleadsarepushed
firmlyandfullyin.
4
5
– + –+
1
– + –+
2
3
8