User Manual

ManualsBrandsRinnai ManualsAppliance AccessoriesFlue Pipe 1000mm Long

INFINITY 26i – REU-VR2632FFUG

HD 200i – REU-VRM2632FFUC

Rinnai FF coaxial flue system, suitable

for use with the following Rinnai internal

continous flow water heater models:

FF Flue

Installation

Manual

These components shall be installed in accordance with:

• Manufacturer’s Installation Instructions

• Current AS/NZS 3000, AS/NZS 3500 & AS 5601

• Local Regulations and Municipal Building Codes

These components must be installed, serviced and removed by an Authorised Person.

Summary of content (12 pages)

PAGE 1
FF Flue Installation Manual Rinnai FF coaxial flue system, suitable for use with the following Rinnai internal continous flow water heater models: INFINITY 26i HD 200i UP These components shall be installed in accordance with: • Manufacturer’s Installation Instructions • Current AS/NZS 3000, AS/NZS 3500 & AS 5601 • Local Regulations and Municipal Building Codes These components must be installed, serviced and removed by an Authorised Person.
PAGE 2
PAGE 3
INSTALLATION GENERAL This flue must be installed by an authorised person. The Installation must conform to local regulations. Installation must comply with the instructions supplied by Rinnai. Service and removal must be carried out by an authorised person. TABLE OF CONTENTS CERTIFICATION ....................................................................................... 1 GENERAL .................................................................................................. 1 FF FLUEING OPTIONS ...
PAGE 4
FF FLUEING OPTIONS FFSBEND FFWPLATE or FFWSEAL (Optional) FFWPLATE or FFWSEAL (Optional) FFSBEND 127mm Hole DIRECT HORIZONTAL (FIG. 1) 127mm Hole 2° fall to terminal 2° fall to terminal FFWPLATE FFWPLATE FFWALLTERM Drain Tube Cap FFWALLTERM Drain Tube Cap 45 minimum FFPIPE1000 VERTICAL (FIG. 3) A vertical installation that consists of flue pipe(s) (FFPIPE1000) and a roof terminal (FFROOFCOWL). See page 5 for details. FFWALLTERM VERTICAL / HORIZONTAL (FIG. 4) 2° fall to terminal Fig.
PAGE 5
GENERAL INSTALLATION METHODS Lubricating Components A container of "O ring" grease is provided with the flue terminal components (FFWALLTERM and FFROOFCOWL). To ease assembly, lubricate the “O” ring on the inner pipes of each flue component prior to assembly. Use only a silicone based "O" ring seal lubricant. DO NOT use petroleum based lubricants such as petroleum jelly, as such products may cause deterioration.
PAGE 6
DIRECT HORIZONTAL FLUE The Rinnai water heater 'direct' flueing components (FFSBEND, FFWALLTERM, FFWSEAL and FFWPLATE) must be used for this purpose. Mount the water heater in an appropriate location ensuring that there is enough space to install the flue assembly and pipe work. Also ensure that positioning of the flue terminal complies with the requirements of AS5601 (Fig.5.3 on page 9). Ø127 Wall penetration FFSBEND 2.
PAGE 7
VERTICAL FLUE This option can be used when the water heater is to be flued vertically through the roof. The Rinnai water heater 'Vertical Flueing Components' (FFROOFCOWL and FFPIPE1000) with extension pieces (FFPIPE1000) and optional roof seal (FFSEAL) must be used for this purpose. With vertical flue systems the condensate drain pipe will require connection if the total length of the flue system exceeds 2 metres. Refer to the section “CONDENSATE DRAIN” on page 6 for details.
PAGE 8
CONDENSATE DRAIN The condensate trap and associated drain connection are integral with the appliance flue spigot. The condensate trap collects any condensate from the flue system, thereby preventing condensate from entering the water heater and causing damage. A condensate drain tube kit is supplied with the terminals (FFWALLTERM and FFROOFCOWL) and will require connection to the condensate drain connection in flue systems where the total length exceeds 1.
PAGE 9
CONDENSATE DRAIN (b) The point of discharge from each drain line shall be located so that the release of condensate does not cause a nuisance, is readily discernible and incurs no risk of damage to the building. In view of (a) and (b), suitable points of discharge are deemed to be drains, sewers or pits. (c) There shall be no tap, valve or other restrictions in any line. (d) Each line shall fall continuously from the valve to the approved point of discharge.
PAGE 10
DIMENSIONS 64.5 165 85 5 176 66 80 85 FFBEND (2x 45° Bends) 114 85 FFSBEND 15 80 15 15 92 5 5 166 130 66 64.
PAGE 11
CLEARANCES Rinnai Australia 9 Installation Manual
PAGE 12
CONTACT INFORMATION Australia Pty. Ltd. Internet: www.rinnai.com.au E-mail: enquiry@rinnai.com.au ABN 74 005 138 769 Head Office National Help Lines 10-11 Walker Street, Braeside, Victoria 3195 P.O. Box 460 Tel: (03) 9271 6625 Fax: (03) 9271 6622 Sales & Service Tel: 1300 555 545* Fax: 1300 555 655* Spare Parts & Technical Info Tel: 1300 366 388* Fax: 1300 300 141* *Cost of a local call Higher from mobile or public phones.