Quick Start Doorbell Wired Chime
Doorbell Wired Chime 1. Open the Ring app and select Set Up Device. Then follow the in-app instructions. 1. Plug in your Chime 2 . Scan th is code. This identifies your Ring device to make setup fast and easy. 2. Open the Ring app and select Set Up Device. Then follow the in-app instructions. 3. Scan this code. This identifies your Ring Chime device to make setup fast and easy. 73613 For additional help, v1s1t ring .
User Guide Doorbell Wired
Included hardware. Bag Hardware -~ ( ... , , Mounting Screws ~ (2) Wall Anchors @})ml ,2., 3/16" Security Screws e =w=-::i:•======::c:.c_=~ 1x Jumper Cable 0 2 Don't have an existing doorbell?You can power your Door bell Wired directly using our Plug-in Adapter. Visit ring.com / accessories to learn more.
Download the Ring App. The Ring App walks you through setting up and 111anaging your Ring Doorbell. 11 Search for "Ring in one of the app stores below, or visit ring.com/app I • Dcn,r,_laad en lhtl App Store - GETlrOtf J "" Google Play Set up your Ring Doorbell. In the Ring app, select Set Up a Device and follow the in-app instructions. Find your doorbell chime. Your Doorbell Wired is designed lo replace an existing doorbell button, and gets its power from the doorbell system.
Turn off power at the breaker. This is essential to keeping you and your new Ring Doorbell safe. If you're not sure which breaker controls your doorbell chin1e, turn off the master breaker for your home, or contact an electrician. CAUTION! You'll be working with electrical wires during the instaJI process. If you are uncomfortable or inexperienced with doing so, consult with a licensed electrician.
Grab the included Jumper Cable. The Jumper Cable bypasses and disables your existing doorbell chime, and n1ust be installed before you install your Ring Doorbell. Your Doorbell Wired is compatible with doorbell systems supplying 10-24 volts AC, at 50 or 60Hz, 40VA max. The AC connector is the class 2 energy source.
Remove the cover from your doorbell chime. After you've located your doorbell chime and turned off power at the breaker, remove the cover from your chime and set it aside for now. Loosen the "Front" and "Trans" terminal screws. Make sure to keep the existing doorbell wires in place.
Connect the Jumper Cable. Connect one end of the Jumper Cable to Lhe "Front)) terminal, and the other to the nTrans" terminal. It doesn't matter which wire you connect to which terminal. Then re~tighten the terminal screws.
Uninstall your existing doorbell button . Remove your doorbell fro111 the wall. Disconnect the wires. Make sure they don't fall back inside your wall so you can access them later. Remove the faceplate. Grasp the bottom of the faceplate and pull to remove . .
Mark the screw holes. Using your Ring Doorbell as a template 1 mark the location of the two n1ounting holes on your wall. (.
Install the anchors. (optional) On stucco, brick, or concrete, use a ¼ 11 masonry bit to drill holes in your wall, then insert the included wall anchors. (Ifyou're installing on wood or siding, you can skip this step.
Connect the doorbell wires. Loop one doorbell wire around each of the screw terrninaJs on the rear of your Ring Doorbell then tighten the tern1inals to secure.
Screw in your Ring Doorbell . Mount your Ring Doorbell with the two included mounting screws. Be sure to feed any excess wiring back into the wall first. DO NOT USE any screw other than the included mounting screws when securing your Ring Doorbell. ✓ o l 0, / \ 12 l ~ 1" Mounting screw X (IDm1lJ 3/ 16" Security screw
Restore power at the breaker. .,lt may take a n,oment for your Ring Doorbell to power on. You'll know it's ready once it lights up and speaks to you.
Secure your Ring Doorbell. Re-attach the faceplate, then use the included screwdriver to drive the small security screw into the bottom of your Ring Doorbell. CAUTION! If you use the wrong screws to secure the Video Doorbell, you could damage the battery during installation, create a fire hazard, and be seriously injured.
Set up your Chime. Open the Ring App and select Set Up Device. Tap Chimes and scan the code on the back of your device. Plug your Chime into a power outlet and wait for it to power up. Follow the in-app instructions to complete selup.
Review, share and download . Your new device comes with a free 30-day trial of Ring Protect video recording service. To continue your subscription and save your videos, please visit ring.
What is Ring Protect? Ring Protect is a subscription service that stores videos f ron1 your Ring devices. Why do I want it? Ring lets you interact with visitors and monitor your property in real time, while Ring Protect allows you review and share those videos onytirne. How much does it cost? Ring Protect Basic covers one Ring device for $3 USD/ month or- $30 USO/year.* Ring Protect Plus covers all Ring devices at one property, and cosls $10 USD/rnonlh or $100 USO/year.
For additional he'lp, visit ring.com/ help Or give us a call: us 1 800 656 191 8 Canada 1 855 300 7289 Worldwide + 1 31 0 929 7085 For a list of all our customer support numbers, visit ring.com/callus For lnfo~matior, on our warranty, theft protec.tiori, and Ring Protect Plan'i, see rang.
it• 2021 Ring l LC or its affiltates . Ring and all related marks are uademarks of Rrng LLC or ,ts affiliates.
Important Product Information DOORBELL WIRED & SAFETY INFORMATION: FAILURE TO FOLLOW THESESAFETY INSTRUCTIONS COULD RESULT IN FIRE, ELECTRIC SHOCK, OR OTHER INJURY OR DAMAGE. Your device can withstand outdoor use and has been tested to withstand water projected through a 6.3mm nozzle at a volume of 12.5 liters per minute and a pressure of 30 kPa at a distance of 3 meters for at least 3 minutes. However, your device is not intended for underwater use.
The party responsible for FCC compliance is: Ring LLC, 1523 26th St, Santa Monica, CA USA, 90404 FCC Radiation Exposure Statement This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules.
