Owner's Manual
Table Of Contents
Verify
that
the
supply
voltage
is
correct.
Connect
fixture
to
a
100
VAC-240
VAC
50/60
Hz
power
source.
Properly
ground
fixture.
Al
ways
install wiring
connec
t
ions
in
accor-
dance
with l
ocal
code
standards.
Product Specifications
Device
Name
:
Ring
Flood
light
Cam
Wired
Plus
Model
Number:
5AT3T2
Electrical
Rating:
Hardwired
(110
to
240V)
Temperature
Rating:
5°F
to
120°F
(-20.5°(
to
48.5°()
RECYCLING
YOUR
DEVICE
PROPERLY
In
some
ar
eas,
the
disposal
of
certain electronic
devices
is
regulated.
Make
sure
you
dispose
of,
or
recycle,
your
device
in
accordance
with
your
local
laws
and
regulations.
For
information
abou
t
recycling
your
device,
go
to
amazon
.
com
/devicesupport.
Terms
of
Service
and
Warranty
Use
of
the
product
1s
subject
to
your registration with
Ring
and
your
agreement
with
the
Terms
of
Service
found
at
ring.com/terms
To
review
your
warranty
coverage,
please
refer
to
the
enclosure
inside
this
box or visit
ri
ng
.
com
/ warranty
For
Consumers
in
the
USA
This
device
complies with
Part
15
of
the
FCC
Rules.
Operation
is
subject
to
the
follow-
ing two conditions: (1) this
device
may
not
cause
harmful interference,
and
(2)
this
device
must
accept
any
interference
received,
including interference that
may
cause
undesired
operation.
NOTE:
This
equipment
has
been
tested
and
found
to
comply
with
the
limits
fo
r a
Class
B digital
device,
pursuant
to
Part
15
of
t
he
FCC
Rules.
These
limits
are
designed to
provide
reasonable
protection
against
harmful
interf
erence
in
a
residential
installation.
This
equipment
generates,
uses
and
can
radiate radio frequency
energy
and,
if
not
i
nstalled
and
used
in
accordance
with
the
instructions,
may
cause
harmful
interference
to
radio
communicati
ons.
However,
there
is
no
guarantee
that interference will not
occur
in
a particular
installa-
tion. If
this
equipment
does
cause
harmful
interference
to
radio
or
television
reception,
which
can
be
determined
by
turning
the
equipment off
and
on,
the
user
is
encouraged
to
try
to
correct
the
interference
by
one
or
more
of
the
following
measures:
•
Reorient
or
relocate
the
receiving
antenna.
•
Increase
the
separation
between
the
equipment
and
receiver.
•
Connect
the
equipment into
an
outlet
on
a circuit different
from
that
to
which
the
receiver
is
connected.
•
Consult
the
dealer or
an
experienced
radio/TV
technician for
help.
Pursuant
to
Section
15.21
of
the
FCC
rules,
changes
or modifications
to
a
Product
by
the
user
that
are
not
expressly
approved
by
the
party
responsible
for
compliance
could
void
the
user's
au
thority to
operate
the
equipment.
The
devi
ce
meets
the
FCC
Radio
Frequency
Emission
Guidelines. Information
on
the product
is
on
file with the
FCC
and
can
be
found
by
inputting
such
Product's
FCC
ID
(which
can
be
found
on
the
device) into
the
FCC
ID
Search
form available at
fcc.gov/
oe
t/
ea
/
fccid.
The
party
responsible
for
FCC
compliance
is:
Ring
LLC,
1523
26th
St.
Santa
M
onica,
CA
USA,
90404