Quick Start 1. Open the Ring app and select Set Up Device. Then fol low t e in-app instructions. 2. Scan this code. This 1dent1~1es your Ring device to make setup fast and easy. 15559 For additional help, v1s1t ring.
User Guide Doorbell Wired
Included hardware. Find your doorbell chime. Bag Your Doorbell Wired is designed to replace an existing doorbell button, and gets its power from the doorbell system. Hardware A (2) 1" Mounting Screws (2) Wall Anchors B (2) 3/16" Security Screws C 1x Jumper Cable Ring your existing doorbell and listen for the chime. If it rings, we know your existing doorbell system is working. Follow the sound to find your chime and make a mental note of the location. We’ll return to your chime soon.
Turn off power at the breaker. Grab the included Jumper Cable. This is essential to keeping you and your new Ring Doorbell safe. The Jumper Cable bypasses and disables your existing doorbell chime, and must be installed before you install your Ring Doorbell. If you’re not sure which breaker controls your doorbell chime, turn off the master breaker for your home, or contact an electrician. Your Doorbell Wired is compatible with doorbell systems supplying 10–24 volts AC, at 50 or 60Hz, 40VA max.
Remove the cover from your doorbell chime. After you’ve located your doorbell chime and turned off power at the breaker, remove the cover from your chime and set it aside for now. Loosen the “Front” and “Trans” terminal screws. Connect the Jumper Cable. Connect one end of the Jumper Cable to the “Front” terminal, and the other to the “Trans” terminal. It doesn’t matter which wire you connect to which terminal. Then re-tighten the terminal screws. Make sure to keep the existing doorbell wires in place.
Uninstall your existing doorbell button. Remove your doorbell from the wall. Disconnect the wires. Make sure they don’t fall back inside your wall so you can access them later. Mark the screw holes. Using your Ring Doorbell as a template, mark the location of the two mounting holes on your wall. Remove the faceplate. Grasp the bottom of the faceplate and pull to remove.
Install the anchors. (optional) On stucco, brick, or concrete, use a ¼" masonry bit to drill holes in your wall, then insert the included wall anchors. Connect the doorbell wires. Loop one doorbell wire around each of the screw terminals on the rear of your Ring Doorbell then tighten the terminals to secure. (If you’re installing on wood or siding, you can skip this step.
Screw in your Ring Doorbell. Restore power at the breaker. Mount your Ring Doorbell with the two included mounting screws. It may take a moment for your Ring Doorbell to power on. You’ll know it’s ready once it lights up and speaks to you. Be sure to feed any excess wiring back into the wall first. DO NOT USE any screw other than the included mounting screws when securing your Ring Doorbell.
Download the Ring App. Secure your Ring Doorbell. The Ring App walks you through setting up and managing your Ring Doorbell. Re-attach the faceplate, then use the included screwdriver to drive the small security screw into the bottom of your Ring Doorbell. Search for “Ring” in one of the app stores below, or visit ring.com/app CAUTION! If you use the wrong screws to secure the Video Doorbell, you could damage the battery during installation, create a fire hazard, and be seriously injured.
For additional help, visit ring.com/help Or give us a call: US 1 800 656 1918 Canada 1 855 300 7289 Worldwide +1 310 929 7085 For a list of all our customer support numbers, visit ring.com/callus For information on our warranty, theft © 2020 Ring LLC or its affiliates. protection, and Ring Protect Plans, see Ring and all related marks are trademarks ring.com/legal of Ring LLC or its affiliates.
Important Product Information & & SAFETY INFORMATION: FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS COULD RESULT IN FIRE, ELECTRIC SHOCK, OR OTHER INJURY OR DAMAGE. SAFELY CONNECTING YOUR RING VIDEO DOORBELL WIRED TO YOUR HOME'S ELECTRICAL WIRING Your device can withstand outdoor use and has been tested to withstand water proJected through a 6.3mm nozzle at a volume of 12.5 liters per minute and a pressure of 30 kPa at a distance of 3 meters for at least 3 minutes.
For information on our warranty, theft protection, and Ring Protect Plans, see ring.com/ legal For Consumers in the USA This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
