Install on a table or shelf You're all set! Just plug in your Stick Up Cam to power it up, and then set up in the Ring App. Install on a wall Go to page 10 in the included manual for more instructions. - "-~ ...... ....'-,- -Install on a ceiling • Go to page 12 in the included manual for more instructions.
• ring .
Download the Ring app. The app walks you through setting up and managing your Stick Up Cam Elite. Search for "Ring" in one of the app stores below1 or visit: ring.
1 Let s get your Stick Up Cam ready. First 1 slide off the bottom cover. Do not reattach this cover until setup is complete! When you plug your Ethernet cable into your Stick Up Cam, be sure to feed it through the hole in this bottom cover first. You'll reattach the cover to your Stick Up Cam in a later step.
Powering your Stick Up Cam Stick Up Cam connects using Power over Ethernet (or PoE). This lets you use one cable for both power and internet. Most Ethernet equipment does not provide PoE) so we)ve included a PoE Adapter. You connect it to your network and a power outlet, then connect it to your Stick Up Cam. If your home is already equipped with a PoE system, you can connect Stick Up Cam directly to a PoE-enabled Ethernet port. • If using an existing PoE hub or switch, ,t must meet the IEEE 802.
Connect your Stick Up Cam . Use the included Ethernet cable to connect the PoE Adapter to you r internet modem or Ethernet switch . Purchase a 2nd Ethernet cable to connect Stick Up Cam to the PoE Adapter. Internet Modem, Ethernet Switch 1 or Hub ••• • Power Outlet I I • PoE Adapter 0 For outdoor use1 install your PoE Adapter indoors, then run an Ethernet cable outdoors to your Stick Up Cam.
Set up your Stick Up Cam in the Ring app. In the Ring app, select Set Up a Device . I 0 i--- --.:;-;;:- When prompted) select Security Cams and foll o w the i n-app instructions. Try it out! After setup, tap the Live View button in the Ring app to see live video from your Sti ck Up Cam. Blue light flashing? If the light on the front of your Stick Up Cam is flashing after setup, it's updating its software.
Choose a location . Stick Up Cam is happy just about anywhere, indoors or out. It comes ready to sit on a flat surface like a table or shelf, but can also be mounted to a wall or ceiling. Choose a spot where it can provide the view you want, within reach of the Ethernet port you 1ve connected to the included Ring PoE Adapter.
Make sure that your Ethernet cable has been routed through the hole in the bottom cover. Then, slide the cover into place on your Stick Up Cam. Secure the cover with the attached screw, using the star-shaped end of the screwdriver bit. Finally, place Stick Up Cam in your chosen position. Your Stick Up Cam is now ready to use.
Remove the plastic cover and rubber pad from the base. You'll put the cover back on once you've mounted your Stick Up Cam . Fl ip the base to the rear. The base of the stand is hinged. Before wall-mounting, flip the base down and behind your Stick Up Cam.
Push the rubber pad back into the base. The rubber pad should sit between your wall and the base of your Stick Up Cam. ... Drive the screws. Hold the round part of the base against your wall, rubberside down. Use the integrated level to ensure ifs straight. Finally1 mount it with the included screws. Then 1 head to page 14 for the final steps.
Remove the plastic cover from the base. You'll put the cover back on once you've mounled your Stick Up Cam. Rotate the stand above the camera: The whole stand can rotate on its axis. Before ceilingmounting, rotate the stand 180 degrees so the base is positioned above your Stick Up Cam.
Drive the screws. Hold the round part of the base against your ceiling) rubber-side down . Then mount it with the included screws. Then) head to page 14 for the final steps.
Close it up. Make sure that your Ethernet cable has been routed through the hole in the bottom cover and is plugged into your Stick Up Cam. Then, slide the cover back into place and secure it with the attached screw, using the star-shaped end of the included screwdriver bit.
Snap the cover back onto the base. Then} secure it with the included security screw, using the star-shaped end of the included screwdriver bit. Now your Stick Up Cam is installed and ready to use.
For add itional help, visit: ring .com/help O r give us a call ... us 1 800 656 1918 Canada 1 855 300 7289 Worldwide + 1 310 929 7085 For a list of all our customer support numbers, visit: nng.com/callus To review your warranty covorage1 plea~ visit www ,, g.
Get the most from your Ring. Your Ring Stick Up Cam comes with a free 30 day trial of our Protect video recording service. It's great for keeping track of what happens at your property. Sign up today. Your first 30 days are still free. To extend your subscription and save your videos, visit: ring .
Q: What is Protect? Protect is a subscription service that stores videos of every event your Ring products capture. Videos are stored for up to 60 days and can be downloaded for long-term storage. Q: Why do I want it? Out of the box1 your Ring lets you interact with visitors and monitor your property in real time. If you 1 d like to be able to review your Ring videos anytime and share them with anyone1 Protect is for you.
Setup Steps ... 1. Download the Rinq app. Search for "Ring)} in the App Store or Google Play Store. Open the app, create an account, tap Set Up a Device, then select Security Cams. 2. Scan this code. This identifies your Ring to make setup fast and easy. 083A88045E11 3. Complete your setup. Continue setup in the Ring app, then install your Stick Up Cam following the supplied instructions.
1523 26th St. Santa Monica, CA 90404 This dev,ce complies w,th Part I 5 o f the FCC Rules. Operation ,s subject to the following two conditions: (I) this device may not cause harmful interference.
