• ring Smoke/CO l_istener For Ring Alarn1 0
Smoke and CO protection for Ring Alarm. Ring Smoke/CO Listener is a smart sound sensor for Ring Alarm. It does not sense smoke or CO directly. Instead, it adds smart functionality to your existing smoke or CO alarm (or smoke/CO combo). When your smoke or CO alarm begins to sound, the Smoke/CO Listener activates and Ring Alarm notifies you of the issue, wherever you are. If your system is professionally monitored, our monitoring center is also notified. Before you i nstal I. ..
Contents 1. Diagram 2. ln-app Setup 3. Physical Installation 4.
Diagram < ::> ••.,.___......._<:; ____ LED ring c::: > ...... .
2. Setup your Ring Smoke/ co Listener in the Ring app.
Begin the setup process near your Ring Alar111 Base Station . In the Ring app, tap Set Up a Device. Choose Security Devices, then Sensors, then Ring Smoke/ CO Listener, then tap Add Device. To complete the setup process, follow the in-app instructions. 0 --- -- ·••~· r -- ' -- ......
When prompted) scan the QR Code or er1ter tl1e Pl N. This begins the pairing process. The QR Code and PIN are on the back of your Listener and in the product packaging. I l ( ~11!1 'l; (!I .
When prompted, fJull out the clear tab. This tLJrns the Listener on. Your Alarm Base Station then finds it automatically. As the Listener pairs to your Alar111 Base Station, its LED ring blinks slowly, then quickly. Once it pairs, the LED glows blue for three seconds. 0 If the Listener does not pair successfully, the LED ring glows red.
I'ls tall your Listener· fir-st. Th0n, test it Lirie up the mountinq bracket. Secure the mounting bracket and mount the Listener. Find a place for the bracket within six inches (1 5.25 cm) of your smoke or CO alarm. You can use the ruler below to make sure. During the setup process, the Ring app will prompt you to test your new Smoke/ CO Listener. Once you've decided on a location, secure the bracket to your ceiling or wall with the included screws.
Test yoLJr Listener. Now, it's time to head back to the Ring app and go through the testing process. When prompted, press the test button on your smoke or CO alarm. If you're not sure where it is, check the instructions. The Ring app will tell you when your Listener has detected the smoke or CO signal from your alarm. If your alarm is a smoke/CO combo, both smoke and CO signals should be detected. If your Listener is unable to detect the signal, your Ring Alarm cannot monitor your smoke or CO alarm.
How to replace the battery: Twist the lid on your Listener counterclockwise and lift to remove. Replace the battery with a fresh CR 123A cell. The Listener then reconnects to your Alarm Base Station automatically. Place the lid back on the Listener, taking care to line up the semi-circle on the rim of the lid with the "open" semi-circle on the base. Twist the lid clockwise to lock it in.
How to remove Ring Smok.e/CO L;stener from your system: Open the side menu in the Ring app and tap Devices1 then Base Station . Next select your Listener and tap the gearshaped icon. Then tap Remove Device. 1 When prompted 1 open the Listener and remove and reinstall the battery to complete the removal. Having troub1e with your Listener? If your Listener stops working or will not connect (even with a good battery)1 try a factory reset. To do this) press and hold the Setup button for 10 seconds.
LED status patterr1s: SmokeorCO alert sound detected Sensor tampered o 1 Blue Blink 3 Red Blinks For info on other LED patterns, visit ring.cor111 ne lp . Do not paint tl1is device! Painting your Listener can prevent it from functioning correctly. Painting smoke or CO alarms can degrade their performance as well) and is strongly discouraged. 2018 Ring LLC or its affiliates RING, ALWAYS HOME, and all related logos are trademarks of Ring LLC or its affiliates.
• 1523 26th St. Santa Monica, CA 90404 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device complies with Industry Canada's licence-exempt RSSs.
However, there is no guarantee that interference w ill not occur in a p articular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the followi ng measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver.
Ring Smoke/CO Listener Z-Wave Device Specifac Key (OS OSK: 5 -172 10
