Rimage DL5200/DLN5200 User Guide
Corporate Headquarters: Rimage Corporation 7725 Washington Avenue South Minneapolis, MN 55439 USA 800 553 8312 (toll free US) Service: +1 952 946 0004 (International) Fax: +1 952 944 6956 European Headquarters: Rimage Europe GmbH Albert-Einstein-Str. 26 63128 Dietzenbach Germany Rimage Corporation reserves the right to make improvements to the equipment and software described in this document at any time without any prior notice.
Rimage DL5200/DLN5200 User Guide Support information US, Asia/Pacific, Mexico/Latin America Europe Rimage Corporation Rimage Europe GmbH Albert-Einstein-Str. 26 63128 Dietzenbach Germany 7725 Washington Avenue South Minneapolis, MN 55439 USA Attn: Rimage Services Tel: +49-(0) 6074-8521-0 Fax: +49-(0) 6074-8521-21 Service: Rimage Europe Technical Website: Email: http://www.rimage.com/support_form.cfm North America: 800-553-8312 Asia/Pacific, Mexico/ Latin America: 952-946-0004 http://www.rimage.
Contents Contents Introduction ...................................................................................... 1 Requirements ..................................................................................................1 Software requirements .......................................................................................... 1 Operating system requirements ............................................................................ 1 Media requirements....................................
Rimage DL5200/DLN5200 User Guide Starting Gemini Utilities ....................................................................................... 15 Changing the autoloader display name............................................................... 15 Enabling the beeper ............................................................................................ 15 Stopping Gemini Utilities ..................................................................................... 15 Learn More ................
Introduction Introduction This manual provides the information needed to operate the DLN5200/DL5200 and identify the parts. To set up and install your DLN5200/DL5200, refer to the Setup and Installation Guide included with your product. The Rimage DLN5200 and DL5200 are robotic-controlled autoloaders containing two recorders, a two-line display panel, and an Everest™ printer.
Rimage DL5200/DLN5200 User Guide Label design requirements For label design requirements, refer to the Everest Printer User Guide. Networking ability To submit orders from a networked PC, refer to the Rimage Advanced Setup Guide (110721).
Identify the parts of the Rimage DLN5200/DL5200 Identify the parts of the Rimage DLN5200/DL5200 This section describes the Rimage DLN5200/DL5200 hardware and its features.
Rimage DL5200/DLN5200 User Guide Rear view - Rimage DLN5200 Printer USB Cable Printer Cable Printer Power Cord PC Power Cord Serial Cable Mouse Cable (if using) Network Connection Keyboard Cable (if using) USB cable Power Switch Power Cord Monitor Cable (if using) Rear view - Rimage DL5200 Printer Cable Printer USB Cable Printer Power Cord Printer Cable USB Cable FireWire Cable Power Switch Power Cord Note: The 9-Pin serial connector is not used.
Identify the parts of the Rimage DLN5200/DL5200 Description of Parts Operator panel Operator Panel The operator panel has a two-line display that informs you of operations or any conditions that require operator intervention. The Rimage DLN5200 displays the name of the embedded PC or product name after it initializes. The computer name is displayed by default. This is helpful in identifying the embedded PC on the network. Refer to the Operate Gemini Utilities section on page 15 to see other options.
Rimage DL5200/DLN5200 User Guide Output trays The Rimage DLN5200/DL5200 is configured with five output trays and an output bin. When a disc is recorded and printed, the lift arm moves the disc to the output bin or one of the output trays. The disc slides out to the end of the tray. The sensor located on each output tray detects if a disc is in the output tray. The output trays are numbered 1 - 5, with 1 located at the top.
Operate the Rimage DLN5200/DL5200 Operate the Rimage DLN5200/DL5200 Powering on Before you begin: Set up the Everest printer. For more information, refer to the Rimage Everest Printer™ setup guide. Powering on the Rimage DLN5200 PC Power Switch 1. Ensure the PC power switch is in the on position. 2. Press the main power switch on the rear of the autoloader to power on the autoloader. Power Switch Note: After powering on the autoloader, the printer initializes. 3.
Rimage DL5200/DLN5200 User Guide Powering off Powering off the Rimage DLN5200 1. Close all open applications. 2. Briefly press the PC power button to shut down the software, Windows, and the embedded PC. p Caution: Do not press and hold the PC power button. If you press and hold the PC power button, the embedded PC will not shut down properly. This may cause data loss or corruption. PC Power Button Note: Powering off the DLN5200 takes approximately 30 seconds. 3.
Operate the Rimage DLN5200/DL5200 Input Bin 3. Place the discs in the input bin with the recording side facing down. - Important! Hold the discs by the edge. Fingerprints affect print quality. 4. Place the input bin on the base plate. 5. Rotate the input bin until it drops into the notches. 6. Close the supply door. Notch Base Plate Removing or installing the front panel Removing the front panel Front Panel Grasp the sides of the front panel and pull out.
Maintain the DLN5200/DL5200 Maintain the DLN5200/DL5200 The procedures in this section will help keep your DLN5200/DL5200 in optimum operating condition. Preventive maintenance schedule Maintenance Procedure Schedule Cleaning the Rimage DLN5200/DL5200 Once a week. Using a damp, lint free cloth, remove dust from the autoloader and surrounding work area. Aligning the Everest printer On installation and as needed. Refer to the instructions below.
Rimage DL5200/DLN5200 User Guide c. Manually rotate the lead screw counterclockwise to move the lift arm down to the print pad. Print Pad Lead Screw 3. Check the disc alignment. To see if the disc is centered, observe the gap between the edge of the disc and the raised edges as shown by the arrows. If the disc requires side to side alignment, continue to step 4. If the disc requires front to back alignment, continue to step 5. 4. If necessary, perform a side to side alignment.
Maintain the DLN5200/DL5200 5. If necessary, perform a front to back alignment. Disc Retainer a. Turn the front to back alignment screw until there is a 1/16” (1.5mm) gap between the front edge of the disc and the raised edge of the disc retainer. # Tip: You can use the Torx T25 driver, or 5/32” Allen wrench, to turn the front to back alignment screw. Gap Distance b. When the printer is aligned, rotate the lead screw to raise the lift arm up about 1.0” (2.5 cm). Lift Arm Print Pad Lead Screw 6.
Maintain the DLN5200/DL5200 Operating Gemini Utilities The Rimage Producer Software Suite includes an application called Gemini Utilities, which is used to update the autoloader firmware. It may also be used to change the display name of the Rimage DLN5200/DL5200 and to enable the beeper. The Rimage DLN5200 displays the computer name on the operator panel. The computer name is helpful when identifying the computer on the network.
Rimage DL5200/DLN5200 User Guide Learn More Rimage DLN5200/DL5200 specifications Note: For printer specifications, refer to your Everest Printer User Guide or PrismPlus! Printer User Guide. Rimage DLN5200 Two disc recorders, Rimage DLN5200 autoloader, an Everest printer, a network-ready embedded PC, and Rimage software. Rimage DL5200 Two disc recorders, Rimage DL5200 autoloader, an Everest printer, and Rimage software. Input Bin Capacity One removable 50-disc bin.
Rimage DL5200/DLN5200 User Guide Technical support and product updates Support for the DLN5200/DL5200 autoloader is available through your authorized reseller. - Important: Be sure to register your Rimage DLN5200/DL5200 autoloader online or complete and return the registration card so we can notify you of upgrades as they become available. Safety information This manual and the indications on the product allow proper and safe operation.
Learn More Safety testing Product name: Rimage DLN5200/DL5200 Model: • DLN5200: RAS15E • DL5200: RAS15 Notice for USA Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
