Rimage DL5200/DLN5200 User Guide
Corporate Headquarters: Rimage Corporation 7725 Washington Avenue South Minneapolis, MN 55439 USA 800-553-8312 (toll free US) Service: +1 952-946-0004 (International) Fax: +1 952-944-6956 European Headquarters: Rimage Europe GmbH Albert-Einstein-Str. 26 63128 Dietzenbach Germany Tel: +49-(0) 6074-8521-0 Fax: +49-(0) 6074-8521-21 Rimage Corporation reserves the right to make improvements to the equipment and software described in this document at any time without any prior notice.
Contents Introduction .............................................................................................................. 1 Important Information.............................................................................................. 2 Support Information.......................................................................................................................... 2 Learn More Online .................................................................................................
Introduction Introduction This manual provides the information needed to operate the DL5200/DLN5200 and identify the parts. To set up and install your DL5200/DLN5200, refer to the Setup and Installation Guide included with your product. The Rimage DLN5200 and DL5200 are robotic-controlled autoloaders containing two recorders, a two-line display panel, and an Everest™ printer.
Rimage DL5200/DLN5200 User Guide Important Information This section provides support contact information, cautions and warnings, and product specifications for the DL5200/DLN5200. Support Information US, Asia/Pacific, Mexico/Latin America Europe Rimage Corporation 7725 Washington Avenue South Minneapolis, MN 55439 USA Attn: Rimage Services Rimage Europe GmbH Albert-Einstein-Str. 26 63128 Dietzenbach Germany Contact Rimage Services: www.rimage.com/support.html Email: http://www.rimage.com/support_form.
Important Information Technical Support and Product Updates Support for the DL5200/DLN5200 is available through your authorized reseller. - Important! Be sure to register your DL5200/DLN5200 so Rimage can notify you of upgrades as they become available. CD and DVD Recording Software Disclaimer This Product, Software, or Documentation may be designed to assist you in reproducing material in which you own the copyright or have obtained permission to copy from the copyright owner.
Rimage DL5200/DLN5200 User Guide Compliance Information Product name: DL5200/DLN5200 Model: DLN5200: RAS15E DL5200: RAS15 Notice for USA NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when this equipment is operated in a commercial environment.
Important Information DL5200/DLN5200 Specifications Note: For printer specifications, refer to your Printer User Guide. Standard system Rimage DL5200 autoloader, an Everest printer, and Rimage software. Rimage DLN5200 autoloader, an Everest printer, a network-ready embedded PC, and Rimage software. Rimage DL5200 Rimage DLN5200 2 2 Number of Recorders Software requirements DL5200: Pentium 4 2.
Rimage DL5200/DLN5200 User Guide Specifications cont: Ribbon requirements Label design requirements 6 Refer to your printer user guide for the correct printer ribbons. Rimage Media Kits™ include the required print ribbons. Refer to your printer user guide for label design requirements.
Identify the Parts of the Rimage DL5200/DLN5200 Identify the Parts of the Rimage DL5200/DLN5200 This section describes the Rimage DL5200/DLN5200 hardware and its features.
Rimage DL5200/DLN5200 User Guide Rear View - Rimage DLN5200 Printer USB Cable Printer Cable Printer Power Cord PC Power Cord Serial Cable Mouse Cable (if using) Network Connection Keyboard Cable (if using) USB cable Power Switch Power Cord Monitor Cable (if using) Rear View - Rimage DL5200 Printer Cable Printer USB Cable Printer Power Cord Printer Cable USB Cable FireWire Cable Power Switch Power Cord Note: The 9-Pin serial connector is not used.
Identify the Parts of the Rimage DL5200/DLN5200 Description of Parts Operator panel The operator panel has a two-line display that informs you of operations or any conditions that require operator intervention. Operator Panel The Rimage DLN5200 displays the name of the embedded PC or product name after it initializes. The computer name is displayed by default. This is helpful in identifying the embedded PC on the network. Refer to the Operate Gemini Utilities section on page 18 to see other options.
Rimage DL5200/DLN5200 User Guide Output bin Output Bin The output bin receives completed and/or failed discs. The output bin holds up to 75 discs. • To remove discs from the output bin, hold the output bin with one hand while moving the bin latch up and then lower the bin. Note: Each time you fill the input bin, • n remove the completed discs from the output bin so the output bin does not become full.
Operate the Rimage DL5200/DLN5200 Operate the Rimage DL5200/DLN5200 Power On Before you begin: Set up the Everest printer. For more information, refer to the Rimage Everest Printer™ setup guide. Power on the Rimage DLN5200 1. Ensure the PC power switch is in the on position. 2. Press the main power switch on the rear of the autoloader to power on the autoloader. Note: After powering on the autoloader, the printer initializes. 3.
Rimage DL5200/DLN5200 User Guide Power Off Power off the Rimage DLN5200 1. Close all open applications. 2. Briefly press the PC power button to shut down the software, Windows, and the embedded PC. n Caution: Do not press and hold the PC power button. If you press and hold the PC power button, the embedded PC will not shut down properly. This may cause data loss or corruption. Note: Powering off the DLN5200 takes approximately 30 3. PC Power Button seconds.
Operate the Rimage DL5200/DLN5200 3. Place the discs in the input bin with the recording side facing down. Input Bin - Important! Hold the discs by the edge. Fingerprints affect print quality. 4. Place the input bin on the base plate. 5. Rotate the input bin until it drops into the notches. 6. Close the supply door. Notch Base Plate Remove or Install the Front Panel Remove the front panel Front Panel Grasp the sides of the front panel and pull out.
Maintain the DL5200/DLN5200 Maintain the DL5200/DLN5200 The procedures in this section will help keep your DL5200/DLN5200 in optimum operating condition. Preventive Maintenance Schedule Maintenance Procedure Schedule Cleaning the Rimage DL5200/DLN5200 Once a week. Using a damp, lint free cloth, remove dust from the autoloader and surrounding work area. Aligning the Everest printer On installation and as needed. Refer to the instructions below.
Rimage DL5200/DLN5200 User Guide c. Manually rotate the lead screw counterclockwise to move the lift arm down to the print pad. Print Pad Lead Screw 3. Check the disc alignment. To see if the disc is centered, observe the gap between the edge of the disc and the raised edges as shown by the arrows. If the disc requires side to side alignment, continue to step 4. If the disc requires front to back alignment, continue to step 5. 4. If necessary, perform a side to side alignment. a.
Maintain the DL5200/DLN5200 b. When the printer is aligned, rotate the lead screw to raise the lift arm up about 1.0” (2.5 cm). Lift Arm Print Pad Lead Screw 6. Exit the diagnostic test. a. Press and hold the operator button to exit diagnostic test 4. The disc is lifted up to the top output tray and released. b. Press the operator button fourteen times and hold on the last press to exit diagnostics. c. 110768_F Press the operator button one time to close the printer tray.
Rimage DL5200/DLN5200 User Guide Operate Gemini Utilities The Rimage Producer Software Suite includes an application called Gemini Utilities, which is used to update the autoloader firmware. It may also be used to change the display name of the Rimage DL5200/DLN5200 and to enable the beeper. The Rimage DLN5200 displays the computer name on the operator panel. The computer name is helpful when identifying the computer on the network.