Rimage DLN5200/DL5200™ User Guide This manual provides the information needed to operate the DLN5200/DL5200 and identify the parts. To set up and install your DLN5200/DL5200, refer to the Setup and Installation Guide.
Corporate Headquarters: Rimage Corporation 7725 Washington Avenue South Minneapolis, MN 55439 USA 800 553 8312 (toll free US) Service: +1 952 946 0004 (International) Fax: +1 952 944 6956 European Headquarters: Rimage Europe GmbH Hans-Böckler-Straße 7 63128 Dietzenbach, Germany Tel: +49-(0) 6074-8521-0 Fax: +49-(0) 6074-8521-21 CD and DVD Recording Software Disclaimer This Product, Software, or Documentation may be designed to assist you in reproducing material in which you own the copyright or have obtaine
Rimage DLN5200/DL5200 Support information US, Asia/Pacific, Mexico/Latin America Europe Rimage Corporation 7725 Washington Avenue South Minneapolis, MN 55439 USA Attn: Rimage Services Rimage Europe GmbH Hans-Böckler-Straße 7 63128 Dietzenbach, Germany Service: FAX: +49-(0) 6074-8521-21 Tel: +49-(0) 6074-8521-0 Rimage Europe Technical Website North America: 800-553-8312 Asia/Pacific, Mexico/ Latin America: 952-946-0004 FAX: 952-946-6956 When you contact Rimage Services, please provide: • Unit seria
Contents Contents Introduction ...................................................................................... 1 Requirements ..................................................................................................1 Software requirements .......................................................................................... 1 Operating system requirements ............................................................................ 1 Media requirements....................................
Rimage DLN5200/DL5200 ii
Introduction Introduction This manual provides the information needed to operate the DLN5200/DL5200 and identify the parts. To set up and install your DLN5200/DL5200, refer to the Setup and Installation Guide included with your product. The Rimage DLN5200 and DL5200 are robotic-controlled autoloaders containing two recorders, a two-line display panel, and an Everest Printer.
Rimage DLN5200/DL5200 Ribbon requirements For ribbon requirements, refer to the Everest Printer User Guide. Label design requirements For label design requirements, refer to the Everest Printer User Guide. Networking ability Using the Rimage Producer Software Suite, you can submit orders to the Rimage DL/DLN5200 from a networked PC or Macintosh. For more information, refer to the Rimage Advanced Setup Guide at http://www.rimage.com.
Identify the parts of the Rimage DLN5200/DL5200 Identify the parts of the Rimage DLN5200/DL5200 This section describes the Rimage DLN5200/DL5200 hardware and its features. Front view Printer Operator Button Transfer Slides Operator Panel Everest Output Trays Lift Arm Recorders PC Power Button Supply Bin Output Note: The PC power button is on only the Rimage DLN5200.
Rimage DLN5200/DL5200 Operator panel Operator Panel The operator panel has a two-line LCD display that informs you of operations or any conditions that require resolution. The Rimage DLN5200 displays the name of the embedded PC or product name after it initializes. The computer name is displayed by default. This is helpful in identifying the embedded PC on the network. Refer to the Gemini Utilities section on page 15 to see other options.
Identify the parts of the Rimage DLN5200/DL5200 Output trays The Rimage DLN5200/DL5200 is configured with five output trays and an output bin. When a disc is recorded and printed, the lift arm moves the disc to the output bin or one of the output trays. The disc slides out to the end of the tray. The sensor located on each output tray detects if a disc is in the output tray. The output trays are numbered 1 - 5, with 1 located at the top.
Rimage DLN5200/DL5200 Rear view - Rimage DLN5200 Printer USB Cable Printer Control Cable Printer Power Cord PC Power Cord Serial Cable Mouse Cable Network Connection Keyboard Cable USB cable Power Cord Monitor Cable 6 110768_D
Identify the parts of the Rimage DLN5200/DL5200 Rear view - Rimage DL5200 Printer Control Cable Printer USB Cable Printer Power Cord Printer Control Cable USB Cable FireWire Cable AC Power Cord Note: The 9-Pin serial connector is not used.
Rimage DLN5200/DL5200 PC power switch The PC power switch supplies power to the embedded PC and autoloader. Note: The PC power switch is on only the Rimage DLN5200. Main power switch The main power switch is used to apply power to the entire system (printer, embedded PC, and the autoloader) The Rimage DLN5200 requires both power switches to be switched to the ‘on’ position.
Operate the Rimage DLN5200/DL5200 Operate the Rimage DLN5200/DL5200 Powering on Before you begin: Set up the Everest printer. For more information, refer to the Everest Printer Unpacking and Setup Guide. Powering on the Rimage DLN5200 1. Press the PC power switch to the ‘on’ position. PC Power Switch 2. Press the main power switch to the ‘on’ position. Note: After pressing the main power Main Power Switch switch to the ‘on’ position, the Everest printer initializes. 3.
Rimage DLN5200/DL5200 Powering off Powering off the Rimage DLN5200 1. Close all open applications. 2. To shut down the software, Windows, and the embedded PC, briefly press the PC power button. p Caution: Do not press and hold the PC power button. If you press and hold the PC power button, the embedded PC will not shut down properly. This may cause data loss or corruption. PC Power Button Note: Power down takes approximately 30 seconds. 3.
Operate the Rimage DLN5200/DL5200 Loading discs The supply bin can be loaded with 50 discs. Use thermal printable discs compatible with the Everest printer. 1. Open the supply door. 2. Remove the supply bin. Supply Door 3. Place the discs in the supply bin with the recording side facing down. - Important! Hold the discs by the edge. Fingerprints affect print quality. Supply Bin 4. Place the supply bin on the base plate. 5. Rotate the supply bin until it drops into the notches. 6.
Rimage DLN5200/DL5200 Maintain the DLN5200/DL5200 The procedures in this section will help keep your DLN5200/DL5200 in optimum operating condition. Preventive maintenance schedule Maintenance Procedure Schedule Cleaning the Rimage DLN5200/DL5200 Once a week. Using a damp, lint free cloth, remove dust from the autoloader and surrounding work area. Aligning the Everest printer On installation and as needed. Refer to the instructions below.
Maintain the DLN5200/DL5200 3. Check the disc alignment. To see if the disc is centered, observe the gap between the edge of the disc and the raised edges as shown by the arrows. If the disc is not centered side to side on the print pad, continue to step 4. Print Pad If the side to side alignment is correct, go to step 5. Lead Screw 4. If necessary, perform a side to side alignment. Front to back Alignment Screw a. Loosen the two side to side alignment screws. b.
Rimage DLN5200/DL5200 5. If necessary, perform a front to back alignment. Disc Retainer a. Turn the front to back alignment screw until there is a 1/16” (1.5mm) gap between the front edge of the disc and the raised edge of the disc retainer. # Tip: You can use the T25 Torx driver, or 5/32” Allen wrench, to turn the front to back alignment screw. b. When the printer is aligned, rotate the lead screw to raise the lift arm up about 1.0” (2.5 cm). Gap Distance 6. Exit diagnostics. a.
Operate Gemini Utilities Operate Gemini Utilities The Rimage Producer Software Suite includes an application called Gemini Utilities, which is used to update the autoloader firmware. It may also be used to change the display name of the Rimage DLN5200/DL5200 and to enable the beeper. The Rimage DLN5200 displays the computer name on the operator panel, which is helpful to identify the computer on the network.
Rimage DLN5200/DL5200 Learn More Rimage DLN5200/DL5200 specifications Note: For printer specifications, refer to your Everest Printer User Guide or PrismPlus! Printer User Guide. Rimage DLN5200 Two disc recorders, Rimage DLN5200 autoloader, an Everest printer, a network-ready embedded PC, and Rimage software. Rimage DL5200 Two disc recorders, Rimage DL5200 autoloader, an Everest printer, and Rimage software. Input Bin Capacity One removable 50-disc bin.
Learn More Operator panel error messages These messages may display on the operator panel. CLAMP FAILURE – The Everest printer tried to clamp a disc but it failed. Check the alignment of the printer to the gripper fingers. Refer to Aligning the Everest printer on page 12. Also, check the discs to ensure they are not warped. SYSTEM PAUSED CHECK DOOR/BIN – The Rimage DLN5200/DL5200 stopped all movement because the door is open.
Rimage DLN5200/DL5200 EVEREST PRINTER OPENING ERROR – The print drawer may be obstructed. Ensure that the printer is seated properly on the printer mounting plate and ensure that the printer is aligned. EVEREST PRINTER RAISE P.H. ERR. – Contact Rimage support. EVEREST PRINTER RETRANSFER OUT – The retransfer ribbon is at the end of the roll and a new retransfer ribbon must be installed. EVEREST PRINTER RETRANSFER GONE – The retransfer ribbon is not installed. Install a retransfer ribbon.
Learn More Technical support and product updates Support for the DLN5200/DL5200 autoloader is available through your authorized reseller. - Important Be sure to register your Rimage DLN5200/DL5200 autoloader online or complete and return the registration card so we can notify you of upgrades as they become available. Safety information This manual and the indications on the product allow proper and safe operation.
Rimage DLN5200/DL5200 Safety Testing Product name: Rimage DLN5200/DL5200 Model: • DLN5200: RAS15E • DL5200: RAS15 Notice for USA Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Learn More Rimage DLN5200/DL5200 Limited 1 Year Warranty/Guarantee Rimage warrants, to the original end user only, that all non-consumable parts of the Rimage DLN5200/DL5200 of automated products will be free from defects in material or workmanship for 12 months, according to the following terms: • Rimage will replace or repair, at Rimage's discretion, any non-consumable parts found defective within the Warranty period. • Valid from the date Rimage ships the product to you.
