Rimage AutoPrinter™ User Guide This manual provides the information needed to operate the AutoPrinter and identify the parts. To setup and install your AutoPrinter, refer to the Setup and Installation Guide included with your This manual provides the information needed to operate the AutoPrinter and identify the parts. To setup and install your AutoPrinter, refer to the user guide included with your printer. Note: The term AutoPrinter applies to both the AutoEverest™ and the AutoPrism.
Corporate Headquarters: Rimage Corporation 7725 Washington Avenue South Minneapolis, MN 55439 USA 800-553-8312 (toll free US) Service: +1 952-946-0004 (Asia/Pacific, Mexico/Latin America) Fax: +1 952-944-6956 European Headquarters: Rimage Europe GmbH Albert-Einstein-Str. 26 63128 Dietzenbach Germany Tel: +49-(0) 6074-8521-0 Fax: +49-(0) 6074-8521-100 Rimage Corporation reserves the right to make improvements to the equipment and software described in this document at any time without any prior notice.
Contents Introduction .............................................................................................................. 1 About this User Guide ...................................................................................................................... 1 About your Product .......................................................................................................................... 1 Optical Disc Recording Software Disclaimer ...............................................
Introduction Introduction This manual provides the information needed to operate and identify the parts of the AutoEverest and AutoPrism AutoPrinter. To set up your AutoPrinter and install the CD Designer™ Software Suite, refer to the set up and installation guide included with your product. About this User Guide • While we try to maintain all versions of our manuals and documentations, please note that the English version found on our web site always contains the most up-to-date information.
Rimage AutoPrinter™ User Guide Important Information This section provides support contact information, safety and compliance information, and product specifications for the Rimage AutoPrinter. Support Information 5B US, Asia/Pacific, Mexico/Latin America Europe Rimage Corporation 7725 Washington Avenue South Minneapolis, MN 55439 USA Attn: Rimage Services Rimage Europe GmbH Albert-Einstein-Str. 26 63128 Dietzenbach Germany Contact Rimage Support: Contact Rimage Europe Support: Website: www.rimage.
Important Information Safety and Compliance Information Safety Precautions 20B This manual and the indications on the product allow proper and safe operation. The indication marks below help protect you and other persons from injury, and equipment from damage. I Warning! According to ANSI (American National Standards Institute) standards, a warning is used to indicate situations that could result in bodily injury to personnel operating or maintaining the equipment.
Rimage AutoPrinter™ User Guide Compliance Information 21B Product Name AutoPrinter II AutoPrinter III Model RAS10 RAS25 Notice for USA NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when this equipment is operated in a commercial environment.
Important Information Rimage AutoPrinter Specifications 9B . Notes: • The most up-to-date technical specifications for the AutoPrinter are located at www.rimage.com/support. From the Support menu select: Printer Series > AutoPrinter > User Manuals tab. • For printer specifications, refer to you Everest or Prism printer user guide or www.rimage.com/support. AutoEverest Standard system Minimum PC requirements Windows PC Macintosh AutoPrinter autoloader, Everest printer and CD Designer™ software suite.
Rimage AutoPrinter™ User Guide AutoEverest AutoPrism Physical size Height 22.5 in (57.2 cm) 22.5 in (57.2 cm) 15 in (38.1 cm) 15 in (38.1 cm) Depth* 23.5 in (59.7 cm) 23.5 in (59.7 cm) Weight 82 lb (37.2 kg) 57 lb (25.9 kg) Width *Leave an additional 3.5 in (9 cm) for cabling. Prints per hour Up to 60 Power 100 – 240 VAC, 1.
Identify the Parts of the AutoPrinter Identify the Parts of the AutoPrinter This section identifies the different parts of the AutoPrinter. For detailed information about the parts of the Everest or Prism printer, refer the printer user guide that shipped with your product.
Rimage AutoPrinter™ User Guide Rear View 12B AutoEverest II AutoPrism II Printer Control Cable USB Cable Printer Control Cable USB Cable Power Cord Power Cord Prism Power Switch Serial Cable* AutoPrinter Power Switch AutoPrinter Power Switch AutoEverest III AutoPrism III Printer Control Cable USB Cable Printer Control Cable USB Cable Power Cord Power Cord Serial Cable* AutoPrinter Power Switch Prism Power Switch AutoPrinter Power Switch * The serial cable is used only for updating th
Operate the AutoPrinter Operate the AutoPrinter This section provides the information needed to operate your Rimage AutoPrinter. Install the Carousel 13B J Important! To prevent errors, install the carousel before operating the software or powering on the AutoPrinter. Bearing Guide 1. 2. 3. Slide the carousel into the AutoPrinter so that the shaft slides into the opening of the bearing guide. Refer to the Front View section on page 7 for proper carousel placement.
Rimage AutoPrinter™ User Guide Load and Unload Discs 15B You can load up to 100 discs per carousel bin. You may load discs in the bins before installing the carousel. When the carousel is installed in the AutoPrinter, discs can be installed one bin at a time by using the following procedure. . Note: Use carousel bins 1, 2, and 3 to load blank discs. Bin 4 is used only for outputting completed discs. Load the Discs 2B 1. 2.
Maintain the AutoPrinter Maintain the AutoPrinter Use the information in this section to keep your AutoPrinter in optimal operating condition. Install the Ribbons 17B & Tips: • • • Before installing ribbons in the Everest or Prism printer, stop any operations. To change ribbons in a Prism printer, refer to the Rimage PrismPlus! Printer User Guide. To change ribbons in an Everest printer, refer to the Rimage Everest Printer User Guide.
Rimage AutoPrinter™ User Guide 4. Align the printer. a. Slowly slide the lift arm down until the disc just touches the print pad. b. If the disc is not centered side-to-side on the print pad, adjust the alignment. Printer Operator Button Lift Arm Side-to-Side Alignment Disc Print Pad Holding Pins Front-to-back Alignment Screw i. ii. Use the Torx T25 screwdriver to loosen the side-to-side alignment screws (Qty. 2). Slide the printer until the side edges of the disc and print pad are aligned.
Maintain the AutoPrinter PrismPlus! Printer @ Required Tools: 26B • • 1. Torx T25 screwdriver 5/32″ Allen wrench Power on the AutoPrinter. & Tip: If the Prism power switch is in the On position, you can power on both the printer and the AutoPrinter by pressing the AutoPrinter power switch. 2. Wait for the system to complete initialization. 3. Prepare the system for alignment. a. Manually slide the lift arm to the top of the AutoPrinter. b.
Rimage AutoPrinter™ User Guide b. Side-to-Side Alignment Screws If the disc is not centered side-to-side on the print pad, adjust the alignment. i. Use the Torx T25 screwdriver to loosen the side-to-side alignment screws (Qty. 2). ii. Slide the printer until the side edges of the disc and print pad are aligned. J Important! Slide the printer only. iii. Do not slide the printer tray. Tighten the side-to-side alignment screws (Qty. 2). & Tip: Tighten each screw in increments to prevent shifting.
