Rimage Amigo IITM User Guide
Corporate Headquarters: Rimage Corporation 7725 Washington Avenue South Minneapolis, MN 55439 USA 800 553 8312 (toll free US) Service: +1 952 946 0004 (International) Fax: +1 952 944 6956 European Headquarters: Rimage Europe GmbH Hans-Böckler-Straße 7 63128 Dietzenbach, Germany Tel: +49-(0) 6074-8521-0 Fax: +49-(0) 6074-8521-21 CD and DVD Recording Software Disclaimer This Product, Software, or Documentation may be designed to assist you in reproducing material in which you own the copyright or have obtaine
Rimage Amigo II Support information US, Asia/Pacific, Mexico/Latin America Europe Rimage Corporation 7725 Washington Avenue South Minneapolis, MN 55439 USA Attn: Rimage Services Rimage Europe GmbH Hans-Böckler-Straße 7 63128 Dietzenbach, Germany Tel: +49-(0) 6074-8521-0 FAX: +49-(0) 6074-8521-21 Service: North America: 800-553-8312 Asia/Pacific, Mexico/ Latin America: 952-946-0004 FAX: 952-946-6956 Rimage Europe Technical Website Rimage Support Website http://www.rimage.de/support.
Contents Contents Introduction ...................................................................................... 1 Requirements ..................................................................................................1 Software requirements .......................................................................................... 1 Operating System requirements............................................................................ 1 Media requirements.....................................
Rimage Amigo II .
Introduction Introduction This manual provides the information needed to operate the Amigo II and identify the parts. To set up and install your Amigo II, refer to the Amigo II Setup and Installation Guide. The Amigo II is available with either the Everest Printer or the PrismPlus Printer. Amigo II with Everest Printer Amigo II with PrismPlus Printer Requirements Software requirements The Amigo II will operate only with the Rimage Producer Software.
Rimage Amigo II Identify the parts of the Amigo II Front view Printer Lift Arm Control Panel Door Recorder Disc Dispenser Operator Panel Carousel Operator Panel There are four LEDs and an operator button on the operator panel. The operator panel is located inside the Amigo II door. Carousel Present LED Active LED Power LED Operator Button Fault LED Operator Button Each time you press the operator button, the carousel rotates to the next bin.
Identify the parts of the Amigo II Status LEDs The following status LEDs provide Amigo II operational information. Image Name Functionality Carousel Present The yellow Carousel Present LED illuminates when the carousel is absent. Active The yellow Active LED illuminates when there is traffic through the control port. It flashes with the carousel present LED to indicate a paused state. Power The green Power LED illuminates when the Amigo II is powered on.
Rimage Amigo II Operate the Amigo II This section provides information that you need to produce CDs or DVDs with the Amigo II. Powering on the Amigo II 1. To power on the Amigo II, press the power switch on the rear of the Amigo II. The Amigo II initializes. Power Switch 2. To power off the Amigo II, press the power switch again. Pausing the system 1. To pause the Amigo II, open the door. 2. To resume operation, close the door. Loading and unloading discs 1. Load the discs. a. Open the door. b.
Operate the Amigo II Setting up your printing preferences Printing Preferences allows you to set up and run your Amigo II to produce the best possible label on your discs. Please refer to your Everest Printer User Guide or PrismPlus! Printer User Guide for specific printing preferences instructions.
Rimage Amigo II Maintain the Amigo II Maintenance schedule Task Frequency Clean the Amigo II Once a week. Remove dust from Amigo II and surrounding work area using a lint-free cloth. Align the printer Upon installation and again if the printed label is not centered on the disc. Refer to the procedures below for more information. Note: For information on cleaning and maintaining your printer, refer to your Everest Printer User Guide or PrismPlus! Printer User Guide.
Maintain the Amigo II 4. Align the printer. a. Slowly move the lift arm down until the disc just touches the print pad. Printer Button Lift Arm Side to Side Alignment Print Pad Holding Pins b. If the disc is not centered side to side on the print pad, align the printer side to side. i. ii. Loosen the side to side screws. Slide the printer, not the print drawer, until the side edges of the disc and printer pad are aligned. iii. Tighten the side to side screws. Side to Side Screws Front to Back Screw c.
Rimage Amigo II PrismPlus printer To align your PrismPlus printer, refer to the following instructions. Required tools: • T 25 Torx screwdriver • 5/32” Allen wrench 1. To power on the Amigo II, press the PrismPlus power switch and the Amigo II power switch. 2. Wait for the unit to complete the initialization. 3. Prepare the unit for alignment. a. Manually move the lift arm to the top of the Amigo II. b.
Maintain the Amigo II b. If the disc is not centered side-to-side on the print pad, align the printer side to side. i. Loosen the side to side screws. ii. Slide the printer, not the drawer, until the side edges of the disc and printer pad are aligned. iii. Tighten the side to side screws. Side to Side Screws Front to Back Alignment Screw c. Using either the T25 Torx driver or the 5/32” Allen wrench, turn the front-to-back alignment screw until the disc hangs over the edge of the print pad by 0.010” – 0.
Rimage Amigo II Learn more Amigo II Specifications Standard System One disc recorder, Rimage Amigo II autoloader, Everest printer or PrismPlus printer, and software. Software requirements Rimage Producer Software Input bin capacity 300 Discs Output capacity 300 Discs Physical size Width – 15.75 inches (40.6 cm) Height – 22.5 inches (57 cm) Depth – 24.5 inches (62.
Learn more Technical support and product updates Support for the Amigo II is available through your authorized reseller. - Important! Register your Amigo II online or complete and return the registration card so Rimage can notify you of upgrades as they become available. Safety information This manual and the indications on the product allow proper and safe operation. The indication marks below help protect you and other persons from injury, and equipment from damage.
Rimage Amigo II Safety testing Product name: Amigo II Model: RAS9 Notice for USA Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Learn more Rimage Producer II Limited One Year Warranty Rimage warrants, to the original end user only, that all non-consumable parts of the Producer II family of automated products will be free from defects in material or workmanship for 12 months, according to the following terms: • Rimage will replace or repair, at Rimage's discretion, any non-consumable parts found defective within the Warranty period. • Valid from the date Rimage ships the product to you.
