REN/PLUS Versión: 3.0 Instruction manual More information go to www.rilo.com.
Welcome to RILO Instruction manual NOTE TO THE INSTALLER: READ CAREFULLY. ENG The worksurface should have the apropiate size to place both the coffee machine and grinder. It should also have enough space underneath the worksurface to acommodate the pump – in case that is is not a built-in pump- comfortably, the dechlorinating filter or water softener and the and the knock boxes.
Welcome to RILO Instruction manual B: MACHINE DEPTH: 510mm (51cm) C: MACHINE HEIGHT: 480mm (48cm) D: ROOM FOR GRINDER: 300mm (30cm) E: MAXIMUM HEIGHT OF THE WORKSPACE: 950mm (95cm) F: MINIMUM HEIGHT OF THE WORKSPACE: 850mm (85cm) REN PLUS MACHINE A: MACHINE WIDTH : 2 gr. 670mm (67cm) 3 gr.
Welcome to RILO ENG Instruction manual INSTALLATION A. WATER DRAINING A lead or plastic pipe of 1½” at least, should be attached to a ½” hose coming from the drain box of the machine. B. WATER SUPPLY It Should end with a water valve with a screw top or a thread of ½”.If the machine has a built-in pump connect to the valve an 8 mm rubber hose.In case the engine should be separated, connect the hose to the pump entry.
Instruction manual Welcome to RILO C. GAS SUPPLY It should be of a galvanized iron pipe, finished with a valve with a screw top or thread of ½”. The connection from the gas main valve to the machine gas valve has to be done with a 5/16” copper pipe and a female ¼” coupling. ATTENTION: In every case you should let run plenty of water, before you start operating the machine in order to dispose the pipes from any residue that could have been left during the contruction. D.
Instruction manual Welcome to RILO This system was programed to cutt off the filling process at 90 seconds. Hence, the technician who makes the installation, while doing the first load has to take into account , that he should turn on and off the coffee machine as many times as the boiler reaches its proper level. NOTE: Take notice that the size of the boilers vary with each different model.
Welcome to RILO Instruction manual GET TO KNOW YOUR RILO COFFEE MACHINE 1. Coffee groups. 2. Coffee filter-holders 3. Boiler manomenter 4. Electropump manometer 5. Hot water tap 6. Steam wand 7. Group switch 8. Red light boiler resistance (**) 9. On/off Switch 10. Gas knob (*) 11. Switch on button(*) 12.
Instruction manual Welcome to RILO Verify that the water leve is always on the middle of the glass tube(12). Before start the daily operation of the machine, let hot water run through the groups (1) with the filter holders (2) on to promote the warming of the set and the rinsing of them. Verify that the grinding it’s just right and that the amount of ground coffee is the correct one. One stroke for the simple coffee filter and two for the double.
Welcome to RILO Instruction manual INSTRUCTIONS FOR THE TECHNICIAN ON THE GAS REGULATION + TEMPERA- - PILOT + PI LOT - TEMPERATURE 8
Welcome to RILO Instruction manual MAXIMUM TEMPERATURE CALIBRATION. ENG 1. Cut off the electricity between the coffee machine and the main electricity supply. 2. Remove the lid of the pressure switch pulling from the superior edge of the lid. 3. Connect again the machine to the main electricity supply. At this point and after some time the machine will start raising steam pressure in the boiler until it stops. 4.
Welcome to RILO Instruction manual Important: The pressure switches are delivered already calibrated, nevertheless, if you want to regultae it yourself, please follow the previous steps. CALIBRATION OF THE DIFFERENTIAL OF THE SYSTEMS OF MAXIMUM IGNITION (disconnection) AND MINIMUM (re-connection) . To modify the differential pressure handle the 5/16” nut. Turning to the right the difference increases (greater fall of preassure before the re-connection).
Welcome to RILO Instruction manual From the electric point of view the pressure switch it’s a tri-polar interruptor –which uses only 2 poles- that allows the controlling of the connection and disconnection of the resistance that heats the boiler. To replace a faulty pressure switch follow these next steps: Cutt off the electric supply from the machine. Remove the lid pulling from the superior edge.
Instruction manual Welcome to RILO To take note: The central pole of the pressure switch it’s not connected. If the fault is verified in one of the two poles in use, you have the possibility to change the positions of the wires from the faulty pole connecting them to the central pole. IMPORTANT: DO NOT BYPASS OR TRY TO JUMPER NEITHER OF THE POLES OF THE PRESSURE SWITCH IN ORDER NOT TO COMPROMISE THE ELECTRIC SAFETYOF THE MACHINE.
Concordia 1178/86 (C1487DIX) Cuidad Autonoma de Buenos Aires Tel. (54 11) 46710852 (rotativas) Fax. (5411) 4636 1072 e-mail: rilo@dd.com.ar www.rilo.com.
