2HP Dust Collector Owner’s Manual Model: 60-200 Record the serial number and date of purchase in your manual for future reference. Serial number: Date of purchase: For more information: www.rikontools.com or info@rikontools.com For Parts or Questions: Part # 60-200M2 techsupport@rikontools.
Operator Safety: Required Reading IMPORTANT! Safety is the single most important consideration in the operation of this equipment. The following instructions must be followed at all times. There are certain applications for which this tool was designed. We strongly recommend that this tool not be modified and/or used for any other application other than that for which it was designed. If you have any questions about its application, do not use the tool until you have contacted us and we have advised you.
ALWAYS DISCONNECT TOOLS. Disconnect tools before servicing and when changing accessories such as blades, bits, and cutters. ALWAYS AVOID ACCIDENTAL STARTING. Make sure switch is in “OFF” position before plugging in cord. NEVER LEAVE TOOLS RUNNING UNATTENDED. ALWAYS CHECK FOR DAMAGED PARTS. Before initial or continual use of the tool, a guard or other part that is damaged should be checked to assure that it will operate properly and perform its intended function.
Table of Contents Safety Warnings.............................................................................................................................................2-3 Dust Collector Safety Rules .......................................................................................................................3 Specifications ........................................................................................................................................4 Contents of Package ............
Contents of Package When unpacking, check to make sure the following parts are included. If any parts are missing or broken, please call RIKON Power Tools at the number on the cover of this manual as soon as possible.
Assembly Installing Casters to Base Plate Locate the four swivel casters, four 12MM hex nuts and four 12MM hex cap nuts from hardware pack. 1. Insert the threaded stud from swivel caster through one of the four holes in the corner of the base plate. 2. Place 12MM hex nut and 12MM hex cap nut onto threaded stud of swivel caster and tighten (Fig. 01). 3. Repeat steps 1 and 2 for the remaining three swivel caster assemblies. Attaching Motor Base to Base Plate Fig.
Installing the 5” Outlet and Rubber Gasket Locate the 5” plastic outlet, rubber gasket, six M6X20MM hex bolts and six 6MM washers. 1. Place the rubber gasket on the flange of the fan housing (A--Fig. 04). 2. Align the holes of the mounting flange on the fan housing for the holes of the 5” outlet (B--Fig. 04). A 3. Secure the assembly with the six M6X20MM hex bolts and 6MM washers. B Fig.
Assembly Continued Installing the 5” Hose Locate the 5” hose and two hose clamps. A 1. Slip a hose clamp over both ends of the hose (A--Fig. 08). A 3.) Place one end of the hose over the 5” outlet on the fan housing and the other end on the collector. (Fig. 08). Fig. 08 4.) Tighten the clamps with a slotted screwdriver or wrench. Threading Band Straps in Filter Bags 1.) Unfold both bags and lay on a flat surface. 2.) Locate the slit on the right side of the top lip of each bag. 3.
Operation On/Off Locking Switch Caution: Make sure that the On/Off locking switch is in the “Off” position before plugging the dust collector into a power source. The On/Off Locking Switch has a center key that can be used to prevent unauthorized use of the dust collector. The switch needs to have the center key inserted before the machine can be used. (Fig. 11) Fig.
Electrical Requirements In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances. Do not modify the plug provided.
Troubleshooting Wiring Diagram 11
Parts List Key No. 1 3 4 5 6 7 8 9 10 13 14 15 16 17 18 20 Description Caster Base plate Flat washer Motor base Hex bolt Motor cable Motor Switch body Center key Upper bag support Collector support Hex bolt Hex nut Key Fan washer Flat washer Key No.
Parts Explosion 13
Warranty 2-Year Limited Warranty RIKON Power Tools Inc. (“Seller”) warrants to only the original retail consumer/purchaser of our products that each product be free from defects in materials and workmanship for a period of two (2) years from the date the product was purchased at retail. This warranty may not be transferred. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs, alterations, lack of maintenance or normal wear and tear.
Notes
For more information: 16 Progress Rd. Billerica, MA 01821 877-884-5167/978-528-5380 techsupport@rikontools.com www.rikontools.com Copyright RIKON Power Toos Inc.
