25-130H 13” Thickness Planer with Helical Cutterhead 262149 Operator’s Manual Record the serial number and date of purchase in your manual for future reference. Serial Number: _________________________ Date of purchase: _________________________ For technical support or parts questions, email techsupport@rikontools.com or call toll free at (877)884-5167 25-130HM1 www.rikontools.
TABLE OF CONTENTS Specifications.....................................................................................................................2 Safety Instructions ........................................................................................................3 - 6 Getting To Know Your Machine ..............................................................................................7 Contents of Package ......................................................................................
SAFETY INSTRUCTIONS IMPORTANT! Safety is the single most important consideration in the operation of this equipment. The following instructions must be followed at all times. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious personal injury. There are certain applications for which this tool was designed. We strongly recommend that this tool not be modified and/or used for any other application other than that for which it was designed.
SAFETY INSTRUCTIONS 12. KEEP PROTECTIVE GUARDS IN PLACE AND IN WORKING ORDER. 25. ALWAYS WEAR A DUST MASK TO PREVENT INHALING DANGEROUS DUST OR AIRBORNE PARTICLES, including wood dust, crystalline silica dust and asbestos dust. Direct particles away from face and body. Always operate tool in well ventilated area and provide for proper dust removal. Use dust collection system wherever possible.
SAFETY INSTRUCTIONS ELECTRICAL SAFETY EXTENSION CORDS THIS TOOL MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM ELECTRIC SHOCK. THE USE OF AN EXTENSION CORD WITH THIS MACHINE IS NOT RECOMMENDED. For best power and safety, plug the machine directly into a dedicated, grounded electrical outlet that is within the supplied cord length of the machine.
SAFETY INSTRUCTIONS SPECIFIC SAFETY INSTRUCTIONS FOR PLANERS This machine is intended for the surfacing of natural, solid woods. The permissible workpiece dimensions must be observed (see Technical Specifications). Any other use not as specified, including modification of the machine or use of parts not tested and approved by the equipment manufacturer, can cause unforeseen damage and invalidate the warranty. ATTENTION: Use of this planer still presents risks that cannot be eliminated by the manufacturer.
GETTING TO KNOW YOUR MACHINE A On / Off Safety Switch with Reset Button B Depth Gauge C Infeed Extension Table D Thickness Scale E Repeat Cut Indicator F Thickness Adjusting Handwheel G Lifting Handle H Flat Top for Stock Returning H G J A F B E H G C M D L F E I Outfeed Extension Table K J Planer Table J K Dust Chute with End Cover L Tool Storage Holders M Motor & Cutterhead G I SEE PAGES 18 - 21 FOR THE PARTS DIAGRAMS AND PARTS LISTS CONTENTS OF PACKAGE Model 25-130H
CONTENTS OF PACKAGE LIST OF LOOSE PARTS B C D A. B. C. D. E. F. G. H. I. A E F G H Planer Dust Hood & Chute ON/Off Switch Safety Key Lock Handwheel Knob & Screw Hex Wrench 4mm Star T25 Screwdriver Storage Case (empty) for Inserts Dust Chute Cap Manual & Warranty Card (not shown) INSTALLATION MOVING & INSTALLING THE PLANER For portability and secure clamping of the planer to a workbench, the planer can be first permanently bolted to a piece of plywood.
ASSEMBLY INSTALLING THE HANDWHEEL KNOB for Height Setting of the Thickness Table 1. Remove the depth adjustment handwheel by loosening the screw (A), with the supplied 4mm hex wrench. FIG. 1. 2. Install the knob (B) onto the handwheel with the supplied screw (C). 3. Re-attach the handwheel to the planer side and tighten it back in place with the screw (A). FIG. 1 C B A INSTALLING THE DUST PORT 1. From the back of the machine, locate the dust port on the cutterhead assembly.
ADJUSTMENTS LEVELING THE TABLE EXTENSIONS 1. The infeed and outfeed table extensions are attached to the planer. Shipped in a folded, upright position, the table extensions must be in the down position before planing can begin. For accurate planing, the table extensions must be level with the planer table. NOTE: For optimum performance, always check to make sure that the table extensions are level before beginning planing operations. To level: 1.
ADJUSTMENTS REPLANING using the REPEAT CUT 1. Remove the screws to take off the handwheel (1 screw), right side panel (4 screws) and top cover (4 screws). FIG. 5. LOCK NUT STEP BLOCK 2. Lower the cutterhead assembly until the stop screw stops on the step block. STOP SCREW 3. Plane a scrap piece of wood, then measure the thickness of the finished piece. It should be the same as the thickness scale and repeat cut indicator. HANDWHEEL 4.
OPERATION This machine is intended for surface thickness planing of natural, solid woods to a desired thickness, while creating a smooth, level surface. Thickness of each cut will depend on type of wood (hardwood versus softwood), width of workpiece, straightness, dryness, and grain composition. Whenever working with a new type of wood, make thin test cuts on a scrap piece of wood first to determine potential problems with the workpiece. The permissible workpiece dimensions must be observed.
OPERATION POWER SWITCH The planer is turned on by flipping the switch into the up position and it is turned off by flipping the switch in the down position. This planer is also equipped with a special lockout toggle switch that prevents unauthorized use. To prevent unauthorized use of the planer, simply pull out the yellow key located on the face of the switch. See illustration on page 7. • TURN ON THE PLANER: Insert the switch key into the switch, lift the switch to ON.
MAINTENANCE THE MACHINE MUST NOT BE PLUGGED IN AND THE POWER SWITCH MUST BE IN THE 'OFF' POSITION UNTIL ADJUSTMENTS ARE COMPLETE. ROTATING OR REPLACING KNIFE INSERTS This machine has a helical cutterhead with rows of High Speed Steel knife inserts. Each of the 26 inserts on the cutterhead are indexed and have two sharpened sides.
MAINTENANCE POSITIONING BAR SHARP EDGE (S) F F S S FLAT EDGE (F) STAR SCREW F S INDICATOR MARK S FIG. 11 S F S ROTATE INSERT TO INSTALL A NEW SHARPENED EDGE THE MACHINE MUST NOT BE PLUGGED IN AND THE POWER SWITCH MUST BE IN THE 'OFF' POSITION UNTIL ADJUSTMENTS ARE COMPLETE. BRUSH REPLACEMENT Brush life will vary depending on the load placed on the motor. The brushes should be inspected every 10-15 hours of use. To inspect the brushes: 1.
MAINTENANCE Turn the power switch “OFF” and disconnect the plug from the outlet prior to adjusting or maintaining the machine. DO NOT attempt to repair or maintain the electrical components of the motor. Contact a qualified service technician for this type of maintenance. 5. Clean the planer bed columns on a regular basis to prevent the build-up of wood chips and dust. Treat the posts with a dry lubricant spray. Do not use ordinary oil which will collect dust and hamper the operation of the machine. 1.
TROUBLESHOOTING FOR YOUR OWN SAFETY, ALWAYS TURN OFF AND UNPLUG THE MACHINE BEFORE CARRYING OUT ANY TROUBLESHOOTING. SYMPTOM Planer will not start. POSSIBLE CAUSES SOLUTIONS 1. No power 1. Check power source, plug and wiring. 2. Blown shop fuse 2. Check fuse, replace if it is blown. 3. Main on/off switch is not working or the safety key is not inserted 3. Check position of the switches. Contact local dealer for repair or replacement. 4. Motor failure 4. Inspect motor for failed components.
NOTE: Please reference the Manufacturer’s Part Number when calling for Replacement Parts. For Parts under Warranty, the Serial Number of your machine is required.
PARTS LIST KEY NO. 1 2 2-1 3 4 6 7 8 9 10 10-1 11 11-1 13 14 15 16 17 19 20 21 22 25 26 27 28 32 33 34 36 37 38 41 43 44 45 46 47 48 49 50 51 54 55 61 63 65 66 67 68 69 70 71 72 73 74 75 76 77 78 DESCRIPTION Top cover Hex socket button screw M6xP1.0x8L Hex socket button screw M6xP1.0x10L Retainer bearing for top cover Elevation nut 19.85mm Upper frame Left side panel Right side panel Knob Handwheel Screw with washer M5XP0.8X20L Knob Hex socket cap screw M5XP0.
NOTE: Please reference the Part Number when calling for Replacement Parts. For Parts under Warranty, the Serial Number of your machine is required.
197 P25-130H-167 P25-130H-168 P25-130H-170 P25-130H-171 P25-130H-172 P25-130H-173 P25-130H-174 P25-130H-175 Windbreak Screw Electrical protector 20A, A-0701 Switch paddle Switch safety key On/Off switch Motor pin Tap screw Grounding wire 1015#14AWG, 300mm+5R P25-130H-176 External tooth washer Tap screw 167 168 170 171 172 173 174 175 176 177 178 M4.2X20mm 193 192 190 189 188 187 185 184 183 182 6201LLB M4.
ACCESSORIES ADDITIONAL PLANER ACCESSORIES For addtional accessories for use with the 25-130H thickness planer, contact your local RIKON distributor, or visit the RIKON website at www.rikontools.com. 25-499 There you will find Dust Collectors, Dust Hose, Stands, Mobile Bases and other parts and accessories for the RIKON machinery in your shop.
WARRANTY 23
25-130H For more information: 16 Progress Road Billerica, MA 01821 877-884-5167 / 978-528-5380 techsupport@rikontools.com 25-130HM1 www.rikontools.
