Datasheet

19
RIGOL
RS232/UART
DS7000-COMP option
Decode the RS232/UART (up to 20 Mb/s) bus's TX/RX data (5-9 bits), parity (Odd, Even, or None), and stop bits (1-2
bits)
Source channel: CH1 ~ CH4, D0 ~ D15
I2C
DS7000-EMBD option
Decode the address (with or without the R/W bit) of the I2C bus, data, and ACK
Source channel: CH1 ~ CH4, D0 ~ D15
SPI
DS7000-EMBD option
Decode the MISO/MOSI data (4-32 bits) of the SPI bus. The available mode includes "Timeout" and "CS"
Source channel: CH1 ~ CH4, D0 ~ D15
LIN
DS7000-AUTO option
Decode the protocol version (1.X or 2.X) of the LIN bus(up to 20 Mb/s). The decoding displays sync, ID, data, and check
sum
Source channel: CH1 ~ CH4, D0 ~ D15
CAN
DS7000-AUTO option
Decode the remote frame (ID, byte number, CRC), overload frame, and data frame (standard/extended ID, control
domain, data domain, CRC, and ACK) of the CAN bus(up to 5Mb/s). The supported CAN bus signal types include CAN_H,
CAN_L, TX/RX, and DIFF
Source channel: CH1 ~ CH4, D0 ~ D15
FlexRay
DS7000-FLEX option
Decode the frame ID, PL (payload), Header CRC, Cycle Count, Data, Tail CRC, and DTS of the FlexRay bus (up to 10
Mb/s). The supported signal types include BP, BM, and RX/TX
Source channel: CH1 ~ CH4, D0 ~ D15
I2S
DS7000-AUDIO option
Decode I2S audio bus left channel data and right channel data, supporting 4-32 bits. The alignment modes include I2S,
LJ, and RJ
Source channel: CH1 ~ CH4, D0 ~ D15
MIL-STD-1553
DS7000-AERO option
Decode the MIL-STD-1553 bus signal's data word, command word, and status word (address+last 11 bits)
Source channel: CH1 ~ CH4
Auto
Auto
AutoScale Min voltage greater than 5 mVpp, duty cycle 1%, frequency over 35 Hz
Arbitrary Waveform Generator
Arbitrary Waveform Generator (technical specifications are typical values) (option, only for the MSO model)
Number of Channels 2
Output Mode normal (2-channel output)
Sample Rate 200 MSa/s
Vertical Resolution 14 bits
Max. Frequency 25 MHz
Standard Waveform Sine, Square, Ramp, Pulse, DC, Noise
Built-in Waveform Sinc, Exp.Rise, Exp.Fall, ECG, Gauss, Lorentz, and Haversine
Sine
Frequency Range 100 mHz to 25 MHz
Flatness ±0.5 dB (relative to 1 kHz)
Harmonic Distortion -40 dBc
Spurious (non-harmonics) -40 dBc
Total Harmonic Distortion 1%
S/N Ratio 40 dB
Square/Pulse
Frequency Range
Square: 100 mHz to 15 MHz
Pulse: 100 mHz to 1 MHz
Rise/Fall Time <15 ns
Overshoot <5%
Duty
Square: always be 50%
Pulse: 10% to 90%, adjustable
Duty Cycle Resolution 1% or 10 ns (whichever is greater)
Min. Pulse Width 20 ns
Pulse Width Resolution 10 ns or 5 bits (whichever is greater)
Jitter 500 ps