Instructions

ManualsBrandsRigol ManualsLaboratory EquipmentRigol MSO5152-E Digital 150 MHz 2-channel 4 GS/s 100 KP 8 Bit

Table Of Contents

Guaranty and Declaration
Safety Requirement
- General Safety Summary
- Safety Notices and Symbols
- Measurement Category
- Ventilation Requirement
- Working Environment
- Care and Cleaning
- Environmental Considerations
MSO5000-E Series Overview
Document Overview
Quick Start
- General Inspection
- Appearance and Dimensions
- To Prepare for Use
- Front Panel Overview
- Rear Panel Overview
- Front Panel Function Overview
- User Interface
- Touch Screen Controls
- Parameter Setting Method
- To Use the Kensington Security Lock
- To Use the Built-in Help System
- To View the Option Information and the Option Installation
To Set the Vertical System
- To Enable or Disable the Analog Channel
- To Adjust the Vertical Scale
- Vertical Expansion
- To Adjust the Vertical Offset
- Channel Coupling
- Bandwidth Limit
- Probe Ratio
- Input Impedance
- Waveform Invert
- Amplitude Unit
- Channel Delay
- Offset Cal
- Channel Label
To Set the Horizontal System
- To Adjust the Horizontal Timebase
- To Adjust the Horizontal Position
- Delayed Sweep
To Set the Sample System
- Timebase Mode
- Acquisition Mode
- Sampling Mode
- Sample Rate
- LA Sample Rate
- Memory Depth
- LA Memory Depth
- Anti-Aliasing
- Horizontal Expansion
To Trigger the Oscilloscope
- Trigger Source
- Trigger LEVEL/Threshold Level
- Trigger Mode
- Trigger Coupling
- Trigger Holdoff
- Noise Rejection
- Trigger Type
- Zone Trigger
- Trigger Output Connector
Operations and Measurements
- Math Operation
- Auto Measurement
- Cursor Measurement
Digital Voltmeter (DVM) and Frequency Counter
- Digital Voltmeter (DVM)
- Frequency Counter
Power Analysis (Option)
- Power Quality
- Ripple
Histogram Analysis
- To Enable or Disable the Histogram Function
- To Select the Histogram Type
- To Select the Histogram Source
- To Set the Histogram Height
- To Set the Histogram Range
- To Enable or Disable the Statistical Function
- To Reset
Digital Channel
- To Select the Digital Channel
- To Enable/Disable the Digital Channel
- To Set the Threshold and Calibrate Probe
- Auto Arrangement Setting
- To Set the Waveform Display Size
- To Set the Label
- Group Setting
- Waveform Color of the Digital Channel
Protocol Decoding
- Parallel Decoding
- RS232 Decoding (Option)
- I2C Decoding (Option)
- SPI Decoding (Option)
- LIN Decoding (Option)
- CAN Decoding (Option)
- FlexRay Decoding (Option)
- I2S Decoding (Option)
- 1553B Decoding (Option)
Reference Waveform
- To Enable Ref Function
- To Select the Reference Channel
- To Select the Ref Source
- To Adjust the Ref Waveform Display
- To Save to Internal Memory
- To Clear the Display of the Reference Waveform
- To View Details of the Reference Waveform
- To Reset the Reference Waveform
- Color Setting
- Label Setting
- To Export to Internal or External Memory
- To Import from Internal or External Memory
Pass/Fail Test
- To Enable or Disable the Pass/Fail Test Function
- To Start or Stop the Pass/Fail Test Operation
- To Select the Source
- To Create a Mask
- To Save the Mask
- To Load a Mask
- To Set the Output Form of the Test Results
- To Enable or Disable the Display of the Statistics of the Test Results
- Statistics Reset
Waveform Recording & Playing
- Common Settings
- Record Options
- Play Options
Search and Navigation Function
- Search Function
- Navigation Function
Display Control
- To Select the Display Type
- To Set the Persistence Time
- To Set the Waveform Intensity
- To Set the Screen Grid
- To Set the Grid Brightness
- Scale
- Color Grade
- Waveform Freeze
Function/Arbitrary Waveform Generator (Option)
- To Output Basic Waveforms
- To Output the Arbitrary Waveform
- Modulation
  - AM
  - FM
  - FSK
- Sweep
- Burst
Store and Load
- Storage System
- Storage Type
- Load Type
- Internal Storage and Load
- External Storage and Load
- Disk Management
- Factory Settings
System Utility Function Setting
- Remote Interface Configuration
- System-related
Remote Control
- Remote Control via USB
- Remote Control via LAN
- Remote Control via GPIB
Troubleshooting
Appendix
- Appendix A: Accessories and Options
- Appendix B: Warranty
Index

RIGOL Chapter 3 To Set the Horizontal System

3-2 MSO5000-E User Guide

To Adjust the Horizontal Timebase

Horizontal timebase, also called the horizontal scale, refers to the time of each grid in

the horizontal direction of the screen. It is usually expressed in s/div. The adjustable

range of the horizontal timebase is related to the model type.

While you change the horizontal timebase, the displayed waveforms of all channels

are expanded or compressed horizontally relative to the current selected horizontal

reference baseline (refer to "Horizontal Expansion"). The horizontal timebase at

the upper-left corner of the screen will be changed accordingly, as shown in the

figure below.

You can adjust the horizontal timebase with the following three methods:

 Rotate Horizontal

SCALE to adjust the horizontal timebase within the

available range (clockwise to reduce the horizontal timebase and

counterclockwise to increase).

 Enable the touch screen function and adjust the horizontal timebase with the

pinch & stretch gesture on the touch screen. For details, refer to the "Pinch &

Stretch" section.

 Enable the touch screen function, and tap the horizontal timebase label

at the top of the screen. The following window is displayed. Tap the

icon at the right side of the Scale input field to decrease or increase the

horizontal scale. You can also tap the Scale input field to input a specific value

with the displayed numeric keypad.

In the Horizontal control area (Horizontal), rotate the Horizontal

SCALE knob

to switch the adjustment mode between "Coarse" and "Fine" (by default, it is Coarse).

You can also press Acquire  Fine to enable or disable the fine adjustment of the

horizontal timebase.

 Coarse adjustment: Rotate the Horizontal SCALE knob will adjust the

horizontal timebase of the waveforms of all channels at 1-2-5 step within the

adjustable range. Rotate it clockwise to reduce the horizontal timebase, and

counterclockwise to increase the horizontal timebase.

 Fine adjustment: Rotate the Horizontal SCALE knob will adjust the

horizontal timebase of the waveforms of all channels with a minor step value

within the adjustable range. Rotate it clockwise to reduce the horizontal

Decrease the timebase Increase the timebase