Instructions
Table Of Contents
- Guaranty and Declaration
- Safety Requirement
- MSO5000-E Series Overview
- Document Overview
- Quick Start
- General Inspection
- Appearance and Dimensions
- To Prepare for Use
- Front Panel Overview
- Rear Panel Overview
- Front Panel Function Overview
- User Interface
- Touch Screen Controls
- Parameter Setting Method
- To Use the Kensington Security Lock
- To Use the Built-in Help System
- To View the Option Information and the Option Installation
- To Set the Vertical System
- To Set the Horizontal System
- To Set the Sample System
- To Trigger the Oscilloscope
- Trigger Source
- Trigger LEVEL/Threshold Level
- Trigger Mode
- Trigger Coupling
- Trigger Holdoff
- Noise Rejection
- Trigger Type
- Edge Trigger
- Pulse Trigger
- Slope Trigger
- Video Trigger
- Pattern Trigger
- Duration Trigger
- Timeout Trigger
- Runt Trigger
- Window Trigger
- Delay Trigger
- Setup/Hold Trigger
- Nth Edge Trigger
- RS232 Trigger (Option)
- I2C Trigger (Option)
- SPI Trigger (Option)
- CAN Trigger (Option)
- FlexRay Trigger (Option)
- LIN Trigger (Option)
- I2S Trigger (Option)
- MIL-STD-1553 Trigger (Option)
- Zone Trigger
- Trigger Output Connector
- Operations and Measurements
- Digital Voltmeter (DVM) and Frequency Counter
- Power Analysis (Option)
- Histogram Analysis
- Digital Channel
- Protocol Decoding
- Reference Waveform
- To Enable Ref Function
- To Select the Reference Channel
- To Select the Ref Source
- To Adjust the Ref Waveform Display
- To Save to Internal Memory
- To Clear the Display of the Reference Waveform
- To View Details of the Reference Waveform
- To Reset the Reference Waveform
- Color Setting
- Label Setting
- To Export to Internal or External Memory
- To Import from Internal or External Memory
- Pass/Fail Test
- Waveform Recording & Playing
- Search and Navigation Function
- Display Control
- Function/Arbitrary Waveform Generator (Option)
- Store and Load
- System Utility Function Setting
- Remote Control
- Troubleshooting
- Appendix
- Index
RIGOL Chapter 19 System Utility Function Setting
19-14 MSO5000-E User Guide
Data Source
Press Data Source continuously to select "Memory" or "Screen" as the
source of the saved waveform.
Format
Press Format and then rotate the multifunction knob to select the
waveform format. Press down the knob to select it. You can also press
Format continuously to select or enable the touch screen to tap the format.
When Data Source is "Screen", the available formats are "*.bin" and "*.csv".
When Data Source is "Memory", the available formats are "*.bin", "*.csv",
and "*.wfm".
Storage Channel
If "Memory" is selected under Data Source, you need to set the storage
channel. Press Channel and then rotate the multifunction knob to select
the storage channel. You can also press Channel continuously to select the
channel or enable the touch screen to tap the desired channel. The available
storage channels include CH1-CH2 and D0-D15.
3. Setup Saving
When the Quick shortcut key is set to "Save Setup", press Quick on the front
panel to save the setup of the oscilloscope.
Press Operation and then rotate the multifunction knob to select "Save
Setup". Press down the knob to select it. You can also press Operation
continuously to select among the options, or enable the touch screen to tap the
desired operation type. You do not need to set relevant parameters.
4. All Measurement
When the Quick shortcut key is set to "All Measure", press Quick on the front
panel to measure all the parameters of the current measurement source.
Operation Type
Press Operation and then rotate the multifunction knob to select "All
Measure". Press down the knob to select it. You can also press Operation
continuously to select among the options, or enable the touch screen to tap
the desired operation type.
All Measurement
Press All Measure, then rotate the multifunction knob to select the
desired measurement channel. You can also press All Measure continuously
to select or enable the touch screen to tap the desired channel. The available
measurement channels include OFF and CH1-CH2.