Instructions
Table Of Contents
- Guaranty and Declaration
- Safety Requirement
- MSO5000-E Series Overview
- Document Overview
- Quick Start
- General Inspection
- Appearance and Dimensions
- To Prepare for Use
- Front Panel Overview
- Rear Panel Overview
- Front Panel Function Overview
- User Interface
- Touch Screen Controls
- Parameter Setting Method
- To Use the Kensington Security Lock
- To Use the Built-in Help System
- To View the Option Information and the Option Installation
- To Set the Vertical System
- To Set the Horizontal System
- To Set the Sample System
- To Trigger the Oscilloscope
- Trigger Source
- Trigger LEVEL/Threshold Level
- Trigger Mode
- Trigger Coupling
- Trigger Holdoff
- Noise Rejection
- Trigger Type
- Edge Trigger
- Pulse Trigger
- Slope Trigger
- Video Trigger
- Pattern Trigger
- Duration Trigger
- Timeout Trigger
- Runt Trigger
- Window Trigger
- Delay Trigger
- Setup/Hold Trigger
- Nth Edge Trigger
- RS232 Trigger (Option)
- I2C Trigger (Option)
- SPI Trigger (Option)
- CAN Trigger (Option)
- FlexRay Trigger (Option)
- LIN Trigger (Option)
- I2S Trigger (Option)
- MIL-STD-1553 Trigger (Option)
- Zone Trigger
- Trigger Output Connector
- Operations and Measurements
- Digital Voltmeter (DVM) and Frequency Counter
- Power Analysis (Option)
- Histogram Analysis
- Digital Channel
- Protocol Decoding
- Reference Waveform
- To Enable Ref Function
- To Select the Reference Channel
- To Select the Ref Source
- To Adjust the Ref Waveform Display
- To Save to Internal Memory
- To Clear the Display of the Reference Waveform
- To View Details of the Reference Waveform
- To Reset the Reference Waveform
- Color Setting
- Label Setting
- To Export to Internal or External Memory
- To Import from Internal or External Memory
- Pass/Fail Test
- Waveform Recording & Playing
- Search and Navigation Function
- Display Control
- Function/Arbitrary Waveform Generator (Option)
- Store and Load
- System Utility Function Setting
- Remote Control
- Troubleshooting
- Appendix
- Index
Chapter 18 Store and Load RIGOL
MSO5000-E User Guide 18-11
then "文" is input in the "Name Input Area". If the Chinese character is not
found in the current page, press
to go to the next page until you find
the desired character.
4. Input the Other Characters
Refer to Step 3 and use the same method to input the remaining Chinese
characters "件名" in sequence.
5. Modify or Delete the Unwanted Characters that Have Been Entered.
When inputting the filename, you can modify or delete the filename characters
input in the "Name Input Area" as well as delete the pinyin characters input in
the "Pinyin Input Area". To delete the input characters, rotate the multifunction
knob
in the virtual keypad to select the delete key . Press down the key
to delete the characters. To modify the input characters, delete the unwanted
characters and input the desired characters again. If the character to be
modified is in the middle, press the delete key
to delete the characters
starting from the last one to the character to be modified, then input the new
character again.
If the touch screen is enabled, tap to directly move the cursor to the character
required to be modified or deleted, and then input the desired character again
or delete the character.
6. After finishing the input, rotate the multifunction knob
and press OK. The
oscilloscope will create a folder or a specified type of file with this name under
the current directory.
To Delete a File or Folder
1. Delete a File or Folder from the Internal Memory
1) Press Storage Disk and rotate the multifunction knob to select the
internal memory "Local Disk(C)". Press down the knob to open it.
2) Rotate the multifunction knob to select the file or the folder to be
deleted.
3) Press Delete, and then a confirmation dialog box is displayed. Tap to select
"Yes" to delete the file or the folder.
Tip
If characters already exist in the Pinyin input area, when you rotate the
multifunction knob
to delete the characters in the name input area, the
characters in the Pinyin input area will be deleted first.