Instructions
Table Of Contents
- Guaranty and Declaration
- Safety Requirement
- MSO5000-E Series Overview
- Document Overview
- Quick Start
- General Inspection
- Appearance and Dimensions
- To Prepare for Use
- Front Panel Overview
- Rear Panel Overview
- Front Panel Function Overview
- User Interface
- Touch Screen Controls
- Parameter Setting Method
- To Use the Kensington Security Lock
- To Use the Built-in Help System
- To View the Option Information and the Option Installation
- To Set the Vertical System
- To Set the Horizontal System
- To Set the Sample System
- To Trigger the Oscilloscope
- Trigger Source
- Trigger LEVEL/Threshold Level
- Trigger Mode
- Trigger Coupling
- Trigger Holdoff
- Noise Rejection
- Trigger Type
- Edge Trigger
- Pulse Trigger
- Slope Trigger
- Video Trigger
- Pattern Trigger
- Duration Trigger
- Timeout Trigger
- Runt Trigger
- Window Trigger
- Delay Trigger
- Setup/Hold Trigger
- Nth Edge Trigger
- RS232 Trigger (Option)
- I2C Trigger (Option)
- SPI Trigger (Option)
- CAN Trigger (Option)
- FlexRay Trigger (Option)
- LIN Trigger (Option)
- I2S Trigger (Option)
- MIL-STD-1553 Trigger (Option)
- Zone Trigger
- Trigger Output Connector
- Operations and Measurements
- Digital Voltmeter (DVM) and Frequency Counter
- Power Analysis (Option)
- Histogram Analysis
- Digital Channel
- Protocol Decoding
- Reference Waveform
- To Enable Ref Function
- To Select the Reference Channel
- To Select the Ref Source
- To Adjust the Ref Waveform Display
- To Save to Internal Memory
- To Clear the Display of the Reference Waveform
- To View Details of the Reference Waveform
- To Reset the Reference Waveform
- Color Setting
- Label Setting
- To Export to Internal or External Memory
- To Import from Internal or External Memory
- Pass/Fail Test
- Waveform Recording & Playing
- Search and Navigation Function
- Display Control
- Function/Arbitrary Waveform Generator (Option)
- Store and Load
- System Utility Function Setting
- Remote Control
- Troubleshooting
- Appendix
- Index
Chapter 18 Store and Load RIGOL
MSO5000-E User Guide 18-5
overwritten and asking you whether to continue or not.
6) Press Save to save the set setup file to the selected folder in "*.stp" format.
Tip
1. After saving the reference waveform, press Ref More Export to enter
the disk management interface of reference waveform file storage.
2. Press Utility PassFail to enable the pass/fail test function. Then press
Mask Save to enter the disk management interface of pass/fail test mask
file storage.
2. Load the Setup File from the Internal Memory (Take Load Setup as an
Example)
1) Press Storage Load Setup to enter the setup load interface. The disk
management interface is displayed automatically. By default, "Local Disk(C)"
is selected.
2) Rotate the multifunction knob or enable the touch screen to open the
internal memory storage interface.
3) Rotate the multifunction knob
to select the desired storage location,
and then press down the knob to open it. You can also enable the touch
screen to select the storage location. Rotate the multifunction knob
to
select
, then press down the knob or enable the touch screen to tap
to go to the previous location.
4) Rotate the multifunction knob
to select the file to be loaded (the default
file type is in "*.stp" format). Then, the Load menu is enabled. Press Load
to load the selected file. You can also enable the touch screen to operate.
Tip
Press Ref More Import to enter the disk management interface of
reference waveform file load.
Press Utility PassFail
to enable the pass/fail test function. Then press
Mask Load
to enter the disk management interface of pass/fail test mask
file load.