Instructions
Table Of Contents
- Guaranty and Declaration
- Safety Requirement
- MSO5000-E Series Overview
- Document Overview
- Quick Start
- General Inspection
- Appearance and Dimensions
- To Prepare for Use
- Front Panel Overview
- Rear Panel Overview
- Front Panel Function Overview
- User Interface
- Touch Screen Controls
- Parameter Setting Method
- To Use the Kensington Security Lock
- To Use the Built-in Help System
- To View the Option Information and the Option Installation
- To Set the Vertical System
- To Set the Horizontal System
- To Set the Sample System
- To Trigger the Oscilloscope
- Trigger Source
- Trigger LEVEL/Threshold Level
- Trigger Mode
- Trigger Coupling
- Trigger Holdoff
- Noise Rejection
- Trigger Type
- Edge Trigger
- Pulse Trigger
- Slope Trigger
- Video Trigger
- Pattern Trigger
- Duration Trigger
- Timeout Trigger
- Runt Trigger
- Window Trigger
- Delay Trigger
- Setup/Hold Trigger
- Nth Edge Trigger
- RS232 Trigger (Option)
- I2C Trigger (Option)
- SPI Trigger (Option)
- CAN Trigger (Option)
- FlexRay Trigger (Option)
- LIN Trigger (Option)
- I2S Trigger (Option)
- MIL-STD-1553 Trigger (Option)
- Zone Trigger
- Trigger Output Connector
- Operations and Measurements
- Digital Voltmeter (DVM) and Frequency Counter
- Power Analysis (Option)
- Histogram Analysis
- Digital Channel
- Protocol Decoding
- Reference Waveform
- To Enable Ref Function
- To Select the Reference Channel
- To Select the Ref Source
- To Adjust the Ref Waveform Display
- To Save to Internal Memory
- To Clear the Display of the Reference Waveform
- To View Details of the Reference Waveform
- To Reset the Reference Waveform
- Color Setting
- Label Setting
- To Export to Internal or External Memory
- To Import from Internal or External Memory
- Pass/Fail Test
- Waveform Recording & Playing
- Search and Navigation Function
- Display Control
- Function/Arbitrary Waveform Generator (Option)
- Store and Load
- System Utility Function Setting
- Remote Control
- Troubleshooting
- Appendix
- Index
RIGOL Chapter 11 Protocol Decoding
11-38 MSO5000-E User Guide
Set the WS source and the threshold
Press WS and rotate the multifunction knob to select the desired
channel, and then press down the knob to select it. You can also press
WS continuously or enable the touch screen to select it. The available
channels include CH1-CH2 and D0-D15.
When you select the analog channel (CH1-CH2), press WS Thre below
WS, then rotate the multifunction knob or use the pop-up numeric
keypad to set the threshold of the WS signal. When you modify the WS
threshold, a dotted line displaying the current threshold level is
displayed on the screen. The dotted line disappears in about 2 s after
you stop modifying the threshold.
Set the data channel source and the threshold
Press Data and rotate the multifunction knob to select the desired
data channel source, and then press down the knob to select it. You
can also press Data continuously or enable the touch screen to select
it. The available channels include CH1-CH2 and D0-D15.
When you select the analog channel (CH1-CH2), press Data Thre
below Data, then rotate the multifunction knob or use the pop-up
numeric keypad to set the threshold of the data signal. When you
modify the threshold of the data signal, a dotted line displaying the
current threshold level is displayed on the screen. The dotted line
disappears in about 2 s after you stop modifying the threshold.
4. Bus Setting
Press Settings to enter the bus setting menu.
Set the word size
Press Word Size, then rotate the multifunction knob or use the
pop-up numeric keypad to set the word size. Its range is from 4 to 32.
Set the receiver word size
Press Receive, then rotate the multifunction knob or use the pop-up
numeric keypad to set the receiver word size. Its range is from 4 to 32.
Alignment
Press Alignment and rotate the multifunction knob to select the
alignment way for data signal. Then press down the knob to select it. You
can also press Alignment continuously or enable the touch screen to
select it. The available alignment ways include I2S, LJ, and RJ.
Set the WS Low
Press WS Low continuously to select "Left" or "Right".