Instructions
Table Of Contents
- Guaranty and Declaration
- Safety Requirement
- MSO5000-E Series Overview
- Document Overview
- Quick Start
- General Inspection
- Appearance and Dimensions
- To Prepare for Use
- Front Panel Overview
- Rear Panel Overview
- Front Panel Function Overview
- User Interface
- Touch Screen Controls
- Parameter Setting Method
- To Use the Kensington Security Lock
- To Use the Built-in Help System
- To View the Option Information and the Option Installation
- To Set the Vertical System
- To Set the Horizontal System
- To Set the Sample System
- To Trigger the Oscilloscope
- Trigger Source
- Trigger LEVEL/Threshold Level
- Trigger Mode
- Trigger Coupling
- Trigger Holdoff
- Noise Rejection
- Trigger Type
- Edge Trigger
- Pulse Trigger
- Slope Trigger
- Video Trigger
- Pattern Trigger
- Duration Trigger
- Timeout Trigger
- Runt Trigger
- Window Trigger
- Delay Trigger
- Setup/Hold Trigger
- Nth Edge Trigger
- RS232 Trigger (Option)
- I2C Trigger (Option)
- SPI Trigger (Option)
- CAN Trigger (Option)
- FlexRay Trigger (Option)
- LIN Trigger (Option)
- I2S Trigger (Option)
- MIL-STD-1553 Trigger (Option)
- Zone Trigger
- Trigger Output Connector
- Operations and Measurements
- Digital Voltmeter (DVM) and Frequency Counter
- Power Analysis (Option)
- Histogram Analysis
- Digital Channel
- Protocol Decoding
- Reference Waveform
- To Enable Ref Function
- To Select the Reference Channel
- To Select the Ref Source
- To Adjust the Ref Waveform Display
- To Save to Internal Memory
- To Clear the Display of the Reference Waveform
- To View Details of the Reference Waveform
- To Reset the Reference Waveform
- Color Setting
- Label Setting
- To Export to Internal or External Memory
- To Import from Internal or External Memory
- Pass/Fail Test
- Waveform Recording & Playing
- Search and Navigation Function
- Display Control
- Function/Arbitrary Waveform Generator (Option)
- Store and Load
- System Utility Function Setting
- Remote Control
- Troubleshooting
- Appendix
- Index
RIGOL Chapter 11 Protocol Decoding
11-20 MSO5000-E User Guide
You can also press MISO continuously or enable the touch screen to
select it. The available channels include OFF, analog channels
(CH1-CH2), and digital channels (D0-D15). When you select an analog
channel (CH1-CH2), press Threshold below the MISO menu, then
rotate the multifunction knob
or use the pop-up numeric keypad to
set the threshold of the MISO data channel.
Press MOSI and rotate the multifunction knob to select the
desired MOSI data channel, and then press down the knob to select it.
You can also press MOSI continuously or enable the touch screen to
select it. The available channels include OFF, analog channels
(CH1-CH2), and digital channels (D0-D15). When you select an analog
channel (CH1-CH2), press Threshold below the MOSI menu, then
rotate the multifunction knob
or use the pop-up numeric keypad to
set the threshold of the MOSI data channel.
Note: MISO and MOSI source channels cannot be both set to "OFF" at
the same time.
5． Data setting
Press Settings to enter the data setting menu.
Endian setting
Press Endian to select "LSB" or "MSB". By default, it is "MSB".
LSB: indicates Least Significant Bit transmission sequence, i.g. the lowest
bit of the data is transmitted first.
MSB: indicates Most Significant Bit transmission sequence, i.g. the highest
bit of the data is transmitted first.
Polarity setting
Press Polarity continuously to select Positive or Negative as the
polarity for data decoding.
Width setting
Press Width, then rotate the multifunction knob or use the pop-up
numeric keypad to set the bits of each frame of data. The available range is
from 4 to 32. By default, it is 8.
6． Display-related setting
Press Display to enter the display setting menu.
Set the display format
Press Format, rotate the multifunction knob to select the display
format of the bus data. Then, press down the knob to select it. You can also
press Format continuously or enable the touch screen to select it. The
available display formats of the bus data are "Hex", "Dec", "Bin", and
"ASCII".